21.120.40 平衡和平衡机 标准查询与下载

GOST R 53578-2009 振动.平衡.平衡标准的使用与应用准则

Vibration. Balancing. Guidance on the use and application of balancing standards

BS ISO 19499:2007 机械振动.平衡.平衡标准的使用和应用指南

ISO 19499:2007 provides an introduction to balancing and directs the user through the available International Standards associated with rotor balancing. It gives guidance on which of these standards should be used. Individual procedures are not included as these will be found in the appropriate International Standards.

Mechanical vibration - Balancing - Guidance on the use and application of balancing standards

ISO 19499:2007 机械振动.平衡.使用和应用平衡标准的指南

This International Standard provides an introduction to banlancing and directs the user through the available International Standards associated with rotor banlancing.It gives guidance in which of these standards should be used.Individual procedures are not included here as here will be found in the appropriate International Standards.

Mechanical vibration - Balancing - Guidance on the use and application of balancing standards

GOST ISO 1940-1-2007 振动.连续(刚性)状态下,转子的平衡品质要求.第1部分:平衡允差规范和验证

Vibration. Balance quality requirements for rotors in a constant (rigid) state. Part 1. Specification and verification of balance tolerances

GOST 20076-2007 平衡机.基本参数及尺寸.精度规范

Vibration. Balancing machines. Description and evaluation methods

GOST R ISO 20806-2007 振动.原位中型和大型轮子平衡.准则和安全保护

Vibration. Balancing of medium and large rotors in situ. Criteria and safeguards

GOST 31322-2006 振动.连接配键的转子元平衡要求

Vibration. Requirements for balancing of rotor elements to be jointed with fitment key

GOST 31321-2006 振动.平衡机.护罩及其他保护措施

Vibration. Balancing machines. Enclosures and other protective measures

GOST 31320-2006 振动.挠性转子机械平衡方法和标准

Vibration. Methods and criteria for the mechanical balancing of flexible rotors

BS ISO 1940-1:2005 机械振动.在恒定(刚性)状态下转子的平衡质量要求.平衡公差的规范和检定

This part of ISO 1940 gives specifications for rotors in a constant (rigid) state. It specifies a) balance tolerances, b) the necessary number of correction planes, and c) methods for verifying the residual unbalance. Recommendations are also given concerning the balance quality requirements for rotors in a constant (rigid) state, according to their machinery type and maximum service speed. These recommendations are based on worldwide experience. This part of ISO 1940 is also intended to facilitate the relationship between the manufacturer and user of rotating machines, by stating acceptance criteria for the verification of residual unbalances. Detailed consideration of errors associated with balancing and verification of residual unbalance are given in ISO 1940-2. This part of ISO 1940 does not cover rotors in a flexible state. The balance quality requirements for rotors in a flexible state are covered by ISO 11342.

Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state - Specification and verification of balance tolerances

DIN ISO 1940-1 Berichtigung 1:2005 对DIN ISO 1940-1-2004的勘误

Corrigendum to DIN ISO 1940-1

Corrigenda to DIN ISO 1940-1:2004-04 (ISO 1940-1:2003/Cor. 1:2005)

DIN ISO 1940-1 Corrigendum 1:2005 机械振动. 恒定（僵状态下化）转子平衡精度要求. 第1部分: 平衡公差规范及核实（ISO 1940-1: 2003）; 英文版本DIN ISO 1940-1: 2004年4月勘误表1

Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state - Part 1: Specification and verification of balance tolerances (ISO 1940-1:2003) Corrigendum 1 to English version of DIN ISO 1940-1:2004-04

ISO 1940-1:2003/cor 1:2005 机械振动.在恒速(刚性)状态下转子的平衡质量要求.第1部分:平衡公差的规范和验证.技术勘误1

This is Technical Corrigendum 1 to ISO 1940-1-2003 (Mechanical vibration — Balance quality requirements for rotors in a constant (rigid) state — Parti: Specification and verification of balance tolerances )

Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state - Part 1: Specification and verification of balance tolerances; Technical Corrigendum 1

KS B ISO 7475-2004(2009) 机械振动平衡机测量站的外壳和其他保护措施

Mechanical vibration－Balancing machines－Enclosures and other protective measures for the measuring station

ISO 20806:2004 机械振动.中型和大型转子的现场平衡的标准和防护装置

This International Standard specifies procedures to be adopted when balancing medium and large rotors installed in their own bearings on site. It addresses the conditions under which it is appropriate to undertake in-situ balancing, the instrumentation required, the safety implications and the requirements for reporting and maintaining records. This International Standard can be used as a basis for a contract to undertake in-situ balancing. It does not provide guidance on the methods used to calculate the correction masses from measured vibration data. NOTE The procedures covered in this International Standard are suitable for medium and large machines. However, many of the principles will be equally applicable to machines of a smaller size, where it is necessary to maintain good records of the vibration behaviour and the correction mass configurations.

Mechanical vibration - Criteria and safeguards for the in-situ balancing of medium and large rotors

DIN ISO 1940-1:2004 机械振动.在恒定(刚性)状态下转子的平衡质量要求.第1部分:平衡公差的规范和检定

The document gives recommendations for determining and verifying unbalance and for specifying related quality requirements of rigid rotors.

Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state - Part 1: Specification and verification of balance tolerances (ISO 1940-1:2003)

ISO 1940-1:2003 机械振动.在恒定(刚性)状态下转子的平衡质量要求.第1部分:平衡公差的规范和检定

GB/T 9239的本部分给出了恒态(刚性)转子的规范并规定了： a) 平衡允差； b) 所需校正平面的数目； c) 检验剩余不平衡的方法。 根据恒态(刚性)转子的机械类型和最高工作转速， 对其平衡品质要求提出了建议。这些建议是以 国内外的经验为基础的。 GB/T 9239 的本部分规定了剩余不平衡检验的验收准则，以协调旋转机械的制造者和用户之间的关系。 GB/T 9239.2 详细探讨了有关平衡误差和剩余不平衡的检验。 GB/T 9239 的本部分不包括挠性状态转子， 对于挠性状态转子的平衡品质要求见GB/T 6557 。

Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state - Part 1: Specification and verification of balance tolerances

ASA S2.72 PART 4-2003 人体照射到全身振动机械评估,第4部分乘客及全体人员的舒适振动和转动评估

Mechanical Vibration and Shock ?Evaluation of Human Exposure to Whole Body Vibration ?Part 4: Guidelines for the Evaluation of the Effects of Vibration and Rotational Motion on Passenger and Crew Comfort in Fixed-Guideway Transport Systems Formerly ANSI

Mechanical Vibration and Shock ?Evaluation of Human Exposure to Whole Body Vibration ?Part 4: Guidelines for the Evaluation of the Effects of Vibration and Rotational Motion on Passenger and Crew Comfort in Fixed-Guideway Transport Systems Formerly ANSI

SAE ARP4163-2003 平衡试验机:工具作业设计准则

This document establishes general design criteria, tolerances, and limits of application for tooling, fixtures and accessories for mounting and driving gas turbine engine rotors on horizontal and vertical balancing machines. For your own safety, while using balancing tooling, regard the safety instructions of the individual supplier. The purpose of this document is to provide a set of tooling and fixture design parameters for balancing machine tooling that will facilitate the understanding of the high degree of readout accuracy and precision balance required for turbine engine rotors, and will assist in achieving compliance with the testing requirements as listed in applicable ARP specifications for balancing.

Balancing Machines: Tooling Design Criteria

JB/T 9390-2002 卧式硬支承平衡机.技术条件

　　本标准规定了通用卧式硬支承平衡机的术语、定义与符号、基本参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存等内容。　　本标准适用于通用卧式硬支承平衡机。

Specifications for horizontal hard-bearing balancing machines