23.020.35 标准查询与下载

GSO ISO 14456:2022 气瓶 气体特性和相关分类 (FTSC) 代码

ISO 14456:2015 gives a list of FTSC (fire potential, i.e. "oxidizing potential and flammability", toxicity, state of the gas, and corrosiveness) codes determined according to the relevant properties of gases and of some liquids that are transported under pressure.

Gas cylinders — Gas properties and associated classification (FTSC) codes

GSO ISO 10460:2022 气瓶 焊接铝合金、碳钢和不锈钢气瓶 定期检查和试验

This document specifies the requirements for the periodic inspection and testing of welded aluminium-alloy, carbon and stainless steel gas cylinders of water capacity from 0,5 l to 150 l intended for compressed and liquefied gas service under pressure and to verify the integrity of such gas cylinders for further service. It also applies, as far as is practical, to cylinders of less than 0,5 l water capacity and greater than 150 l up to 450 l. This document does not apply to the periodic inspection and testing of acetylene cylinders or composite (fully wrapped or hoop-wrapped) cylinders. It is primarily intended for use with cylinders containing industrial gases other than liquefied petroleum gas (LPG). This document may also be applicable to LPG. Requirements for LPG applications are also provided in ISO 10464.

Gas cylinders — Welded aluminium-alloy, carbon and stainless steel gas cylinders — Periodic inspection and testing

GSO ISO 13769:2022 气瓶 钢印标记

This document specifies stamp marking of transportable gas cylinders of volumes greater than 0,12 l and up to or equal to 150 l and tubes of volumes up to or equal to 3 000 l, including: - steel and aluminium-alloy gas cylinders; - composite gas cylinders; - acetylene cylinders; - liquefied petroleum gas (LPG) cylinders (see Annex A); and - small cylinders (see Annex B). Unless noted by exception, the use of "cylinder" in this document refers to the above types of cylinders. Non-refillable cylinders are addressed by this standard.

Gas cylinders — Stamp marking

EN ISO 22434:2022 气瓶.阀门的检查和维护

This document specifies requirements for the inspection and maintenance of valves [including ball valves and valves with integrated pressure regulator (VIPRs)] for: a) refillable transportable gas cylinders; b) cylinder bundles; c) pressure drums and tubes; which convey compressed, liquefied or dissolved gases. This document does not apply to valves for liquefied petroleum gas (LPG). NOTE Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are addressed with the collective term “gas cylinders” within this document. This document is applicable to valves reused at the time of the periodic inspection of gas cylinders, cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas service (see ISO 11621). This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas cylinder filling.

Gas cylinders - Inspection and maintenance of valves (ISO 22434:2022)

BS EN ISO 11114-5:2022 气瓶 气瓶和阀门材料与气体含量的相容性 评估塑料衬里的试验方法

What is ISO 11114-5 - Test methods for evaluating plastic liners about?    ISO 11114-5 is an international organisation for standardization that specifies some gas compatibility test methods to evaluate plastic materials suitable for use in the manufacture of composite gas cylinder liners. ISO 11114-5 is also applicable to the evaluation of the suitability of plastic matrix materials used for Type 5 cylinders.   Some fluids like water, used for cylinders testing, can react positively or negatively when in contact with plastic liners. This compatibility issue is not covered by ISO 11114-5 .

Gas cylinders. Compatibility of cylinder and valve materials with gas contents - Test methods for evaluating plastic liners

BS EN ISO 14246:2022 气瓶 气缸阀门 制造测试和检查

What is ISO 14246 – Manufacturing tests and examinations of gas cylinder valves about?   ISO 14246 is an International Standard that discusses gas cylinders.  The main objective of ISO 14246 is to demonstrate whether gas cylinder vales are fit for purpose.    ISO 14246 specifies the procedures and acceptance criteria for manufacturing tests and examinations (sometimes called "initial inspection and tests") of valves designed and type tested in accordance with ISO 10297.   ISO 14246 is applicable to:   Cylinder valves intended to be fitted to refillable transportable gas cylinders   Main valves (excluding ball valves) for cylinder bundles

Gas cylinders. Cylinder valves. Manufacturing tests and examinations

22/30385433 DC BS EN ISO 11623 气瓶 复合材料气缸和管 定期检查和测试

BS EN ISO 11623. Gas cylinders. Composite cylinders and tubes. Periodic inspection and testing

EN ISO 14246:2022 可运输气瓶.气瓶阀.生产试验和检验

This document specifies the procedures and acceptance criteria for manufacturing tests and examinations (sometimes called "initial inspection and tests") of valves designed and type tested in accordance with ISO 10297. This document is applicable to: a) cylinder valves intended to be fitted to refillable transportable gas cylinders; b) main valves (excluding ball valves) for cylinder bundles; c) cylinder valves or main valves with integrated pressure regulator (VIPR); d) valves for pressure drums and tubes. NOTE Where there is no risk of ambiguity, cylinder valves, main valves, VIPR and valves for pressure drums and tubes are addressed with the collective term “valves” within this document. The principles of these manufacturing tests and examinations can be beneficially applied to cylinder valves type tested to national or International Standards other than ISO 10297.

Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO 14246:2022)

EN 17476:2021+A1:2022 专用液化石油气器具规范 在底盘中装有水平气瓶的液化石油气蒸汽压力器具

This document specifies the construction characteristics, performances and marking related to safety and the rational use of energy of portable, flat gas appliances directly supplied at the LPG vapour pressure, incorporating a gas cartridge complying with EN 417:2012, inserted horizontally in the chassis. NOTE 1 These appliances are referred to in the body of the text as “appliances”. This document covers appliances for outdoor or in well ventilated areas uses only. This document does not cover appliances supplied by an external gas source. For example, the following types of appliances are covered: a) cooking appliances (stoves, barbecues); b) heating appliances. This document specifies the requirements applicable to these appliances or their functional sections whether or not the latter are independent or incorporated into an assembly. Appliances covered by this document are not connected to a flue for the discharge of products of combustion and are not connected to the mains electricity supply. This document covers neither appliances supplied with LPG in the liquid phase nor appliance with fixed integral container which could be refilled by the user. This document does not cover appliances of direct pressure propane category. Requirements for rational use of energy have been considered for stove burners. NOTE 2 However, such requirements have not been considered for the other types of appliances because: - for barbecues, this type of cooking varies according to the type of food and region where the appliance is used; - for heating appliances, all the heat produced is discharged into the environment.

Specifications for dedicated liquefied petroleum gas appliances - LPG vapour pressure appliances incorporating a horizontal cartridge in the chassis

EN ISO 11114-5:2022 气瓶.气瓶和阀门材料与气体含量的兼容性.第5部分:评估塑料衬里的试验方法

This document specifies some gas compatibility test methods to evaluate plastic materials suitable for use in the manufacture of composite gas cylinder liners. It is also applicable to the evaluation of the suitability of plastic matrix materials used for Type 5 cylinders. Some fluids like water, used for cylinders testing, can react positively or negatively when in contact with plastic liners. This compatibility issue is not covered by this document.

Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 5: Test methods for evaluating plastic liners (ISO 11114-5:2022)

EN 14894:2021 液化石油气设备及配件-汽缸和鼓标记

This document specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including: - Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognized by the Competent Authority. - LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognized by the Competent Authority. - Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognized by the Competent Authority. - LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognized by the Competent Authority. NOTE 1 All these types of receptacles are referred to throughout this document as “cylinders”. This document does not specify any requirements for product, hazard or safety-phrase labelling of packaging which can be required to meet ADR or other legislative requirements. NOTE 2 The marking of cylinders is regulated by RID/ADR which take precedence over any clause in this document. The European Directive on Transportable Pressure Equipment 2010/35/EU [8] includes additional marking requirements (π-marking). For countries that are not members of the European Union, the π marking is replaced by their relevant conformity mark.

LPG equipment and accessories - Cylinder and drum marking

BS EN 1439:2021 液化石油气设备及配件 充装前、充装期间和充装后检查可运输可再充装液化石油气钢瓶的程序

What is BS EN 1439 about?    BS EN 1439 on LPG equipment and accessories specifies the procedures to be adopted when checking transportable refillable LPG cylinders before, during and after filling. BS EN 1439 is applicable to transportable refillable LPG cylinders of water capacity not exceeding 150 l and deemed to be fitted with valves.   BS EN 1439 is applicable to cylinders complying with RID/ADR [6] [7] (including pi marked cylinders) and to existing non-RID/ADR cylinder populations.   BS EN 1439 is applicable to the following:   Welded and brazed steel LPG cylinders with a specified minimum wall thickness   Welded steel LPG cylinders without a specified minimum wall thickness

LPG equipment and accessories. Procedure for checking transportable refillable LPG cylinders before, during and after filling

EN ISO 11439:2013/A1:2021 气瓶.车上贮存机动车的天然气燃料用高压气瓶 包含修改件A1,2021

Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles - Amendment 1 (ISO 11439:2013/Amd 1:2021)

EN ISO 11114-2:2021 气瓶.气瓶和瓶阀材料与盛装气体的相容性.第2部分:非金属材料

This document gives guidance on the selection and evaluation of compatibility between non-metallic materials for gas cylinders and valves and the gas contents. It is also applicable to tubes, pressure drums and bundles of cylinders. This document covers composite and laminated materials used for gas cylinders. It does not include ceramics, glasses and adhesives. This document considers the influence of the gas in changing the material and mechanical properties (e.g. chemical reaction or change in physical state). The basic properties of the materials, such as mechanical properties required for design purposes (normally available from the materials supplier), are not considered. Other aspects, such as quality of delivered gas, are not considered. The compatibility data given are related to single component gases but can be applicable to gas mixtures. This document does not apply to cryogenic fluids (this is covered in ISO 21010).

Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2021)

21/30432349 DC BS EN 13322-1 可移动气瓶 可再充装焊接钢气瓶 设计和构造 第1部分：碳钢

BS EN 13322-1. Transportable gas cylinders. Refillable welded steel gas cylinders. Design and construction - Part 1. Carbon steel

KS B ISO 3807-2021 气瓶.乙炔气瓶.基本要求和型式试验

Gas cylinders - Acetylene cylinders - Basic requirements and type testing

KS B ISO 12209-2021 气瓶 压缩呼吸空气气瓶阀的出口连接

Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air

GSO ISO/TR 17329:2021 气瓶 气瓶制造商标记及其分配的射频识别（RFID）代码的识别

ISO/TR 17329:2015 provides an inventory, as far as known at time of publication, of manufacturer's identification marks and their assigned radio frequency identification (RFID) codes according to ISO 21007-1 and ISO 21007-2. The listing includes marks of existing gas cylinder manufacturers, as well as cylinder manufacturers which have ceased production in the past, but whose cylinders can still be in service today. NOTE It is intended to revise Annex A of this Technical Report from time to time in order to update the list of codes and identification marks of gas cylinder manufacturers in accordance with the progressing commercial and economic development in the cylinder manufacturing industry. Any request for inclusion or modification of these identifications is to be made to the ISO/TC 58/SC 4 Secretariat, who would update the information in Annex A after consultation with the committee leadership.

Gas cylinders — Identification of gas cylinder manufacturer marks and their assigned radio frequency identification (RFID) codes

GSO ISO 24431:2021 气瓶 压缩和液化气体（乙炔除外）用无缝、焊接和复合气瓶 充装时检查

ISO 24431:2016 specifies the inspection requirements at the time of filling, and applies to seamless or welded transportable gas cylinders made of steel or aluminium-alloy (Type 1), and for composite transportable gas cylinders (Types 2 to 5 inclusive) for liquefied or compressed gases of a water capacity up to 150 l. It may be applicable to cylinders and tubes with a water capacity between 150 l and 450 l, provided they are inspected and filled as individual cylinders and tubes. ISO 24431:2016 does not apply to acetylene cylinders, bundles of cylinders, tubes, multiple-element gas container (MEGCs) or battery vehicles. ISO 24431:2016 may also be applicable to LPG. For specific LPG applications, refer to ISO 10691. For cylinders manifolded in bundles, refer to ISO 11755.

Gas cylinders — Seamless, welded and composite cylinders for compressed and liquefied gases (excluding acetylene) — Inspection at time of filling

GSO ISO 11119-4:2021 气瓶 可再充装复合气瓶 设计、制造和测试 第4部分：150 升以下的全包裹纤维增强复合气瓶 带有负载共享焊接金属内衬

ISO 11119-4:2016 specifies requirements for composite gas cylinders with load-sharing welded liners between 0,5 l and 150 l water capacity and a maximum test pressure of 450 bar for the storage and conveyance of compressed or liquefied gases. NOTE 1 1 bar = 105Pa = 105N/m2. The cylinders are constructed in the form of a welded stainless steel liner or welded ferritic steel liner or welded aluminium alloy liner and overwrapped with carbon fibre or aramid fibre or glass fibre (or a mixture thereof) in a matrix to provide longitudinal and circumferential reinforcement. The cylinders in this part of ISO 11119 are type 3 fully wrapped cylinders with a load-sharing metal liner and composite reinforcement on both the cylindrical portion and the dome ends. Cylinders produced in accordance with this part of ISO 11119 have a minimum design life of 15 years. Cylinders with test pressure of up to 60 bar have an unlimited design life. ISO 11119-4:2016 does not address the design, fitting, and performance of removable protective sleeves. ISO 11119-4:2016 does not apply to cylinders with seamless liners. For seamless liners, ISO 11119‑2 applies. NOTE 2 ISO 11623 covers periodic inspection and re-testing of composite cylinders.

Gas cylinders — Refillable composite gas cylinders — Design, construction and testing — Part 4: Fully wrapped fibre reinforced composite gas cylinders up to 150 l with load-sharing welded metallic liners