23.040.15 有色金属管 标准查询与下载

18/30377460 DC BS EN 13480-9 金属工业管道 第 9 部分：镍和镍合金管道的附加要求

BS EN 13480-9. Metallic industrial piping - Part 9. Additional requirements for nickel and nickel alloys piping

ASTM B111/B111M-18a 铜和铜合金无缝冷凝器管和套圈的标准规范

1.1 This specification2 establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31⁄8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified:3 Copper or Copper Alloy UNS No. Previously Used Designation Description C10100 OFE Oxygen-free electronic C10200 OFA Oxygen-free without residual deoxidants C10300 . . . Oxygen-free, extra low phosphorus C10800 . . . Oxygen-free, low phosphorus C12000 DLPA Phosphorized, low residual phosphorus C12200 DHPA Phosphorized, high residual phosphorus C14200 DPAA Phosphorized, arsenical C15630 . . . Nickel Phosphorus C19200 . . . Phosphorized, 1 % iron C23000 . . . Red Brass C28000 . . . Muntz Metal C44300 . . . Admiralty Metals, B, C, and D C44400 . . . . . . C44500 . . . . . . C60800 . . . Aluminum Bronze C61300 . . . . . . C61400 . . . Aluminum Bronze, D C68700 . . . Aluminum Brass, B C70400 . . . 95-5 Copper-Nickel C70600 . . . 90-10 Copper-Nickel C70620 . . . 90-10 Copper-Nickel—Welding Grade C71000 . . . 80-20 Copper-Nickel C71500 . . . 70-30 Copper-Nickel C71520 . . . 70-30 Copper-Nickel—Welding Grade Copper or Copper Alloy UNS No. Previously Used Designation Description C71640 . . . Copper-nickel-iron-manganese C72200 . . . . . . A Designations listed in Classification B224. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.) 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

ASTM B523/B523M-18 无缝和焊接的锆和锆合金管的标准规范

1.1 This specification2 covers two grades of zirconium and zirconium alloy seamless and welded tubes. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes

ASTM B359/B359M-18 铜和铜合金无缝冷凝器和整体式热交换器管的标准规范

1.1 This specification2 establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a coldforming process to produce an integral enhanced surface for improved heat transfer. 1.2 The tubes are typically used in surface condensers, evaporators, and heat exchangers. 1.3 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information. Copper or Copper Alloy UNS No. Type of Metal C10100 Oxygen-free electronic C10200 Oxygen-free without residual deoxidants C10300 Oxygen-free, extra low phosphorus C10800 Oxygen-free, low phosphorus C12000 DLP Phosphorized, low residual phosphorus (See Note 1) C12200 DHP, Phosphorized, high residual phosphorus (See Note 1) C14200 DPA Phosphorized arsenical (See Note 1) C15630 Nickel Phosphorus C19200 Phosphorized, 1 % iron C23000 Red Brass C44300 Admiralty Metal Types B, C44400 C, and C44550 D C60800 Aluminum Bronze C68700 Aluminum Brass Type B C70400 95-5 Copper-Nickel C70600 90-10 Copper-Nickel C70620 90-10 Copper-Nickel (Modified for Welding) Copper or Copper Alloy UNS No. Type of Metal C71000 80-20 Copper-Nickel Type A C71500 70-30 Copper-Nickel C71520 70-30 Copper-Nickel (Modified for Welding) C72200 Copper-Nickel NOTE 1—Designations listed in Classification B224. 1.4 Units—The values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification. 1.5 Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification. 1.6 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Sections 1, 12 and 18. 1.7 (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.) 1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipe and Tube. Current edition approved Oct. 1, 2018. Published November 2018. Originally approved in 1960. Last previous edition approved in 2015 as B359/B359M–15. DOI: 10.1520/B0359_B0359M–18. 2 For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-359 in Section II of that Code. *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

ASTM E243-18 电磁（涡流）检验铜和铜合金管的标准实施规程

1.1 This practice2 covers the procedures that shall be followed in eddy current examination of copper and copperalloy tubes for detecting discontinuities of a severity likely to cause failure of the tube. These procedures are applicable for tubes with outside diameters to 31⁄8 in. (79.4 mm), inclusive, and wall thicknesses from 0.017 in. (0.432 mm) to 0.120 in. (3.04 mm), inclusive, or as otherwise stated in ASTM product specifications; or by other users of this practice. These procedures may be used for tubes beyond the size range recommended, upon contractual agreement between the purchaser and the manufacturer. 1.2 The procedures described in this practice are based on methods making use of encircling annular examination coil systems. 1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 1—This practice may be used as a guideline for the examination, by means of internal probe examination coil systems, of installations using tubular products where the outer surface of the tube is not accessible. For such applications, the technical differences associated with the use of internal probe coils should be recognized and accommodated. The effect of foreign materials on the tube surface and signals due to tube supports are typical of the factors that must be considered. See E690 for additional details regarding the in-situ examinations using internal probes. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes

ASTM B394-18 铌和铌合金无缝和焊接管的标准规范

1.1 This specification covers wrought niobium and niobium alloy seamless and welded tubes as follows: 1.1.1 R04200-Type 1—Reactor grade unalloyed niobium, 1.1.2 R04210-Type 2—Commercial grade unalloyed niobium, 1.1.3 R04251-Type 3—Reactor grade niobium alloy containing 1 % zirconium, and 1.1.4 R04261-Type 4—Commercial grade niobium alloy containing 1 % zirconium. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes

ASTM B395/B395M-18 U型无缝铜和铜合金热交换器和冷凝器管的标准规范

1.1 This specification2 establishes the requirements for condenser, evaporator, and heat exchanger U-bend tubes that are manufactured from seamless copper and copper alloy tube. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This specification is applicable to product 2 in. [50 mm] or less, inclusive, in diameter. 1.4 The product shall be produced from one of the following coppers or copper alloys, as specified in the ordering information: Copper or Copper Alloy UNS No. Previously Used Designation Type of Metal C10200 OFA oxygen-free without residual deoxidants C10300 ... oxygen-free, extra low phosphorus C10800 ... oxygen-free, low phosphorus C12000 DLPA phosphorized, low residual phosphorus C12200 DHPA phosphorized, high residual phosphorus C14200 DPAA phosphorized, arsenical C19200 ... phosphorized, 1 % iron C23000 ... red brass C44300 Type B admiralty metal C44400 Type C admiralty metal C44500 Type D admiralty metal C60800 ... aluminum bronze C68700 Type B aluminum brass Copper or Copper Alloy UNS No. Previously Used Designation Type of Metal C70400 ... 95-5 copper-nickel C70600 ... 90-10 copper-nickel C70620 ... 90-10 copper-nickel(modified for welding) C71000 ... 80-20 copper-nickel C71500 ... 70-30 copper-nickel C71520 ... 70-30 copper-nickel(modified for welding) C72200 ... copper-nickel A Designations listed in Classification B224. 1.5 The following safety hazard caveat pertains only to the test methods described in this specification. 1.5.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.) 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes

ASTM B280-18 空调和制冷现场用无缝铜管的标准规范

Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

ASTM C1863-18 连续纤维增强先进陶瓷复合材料管状试样在环境温度下的箍抗拉强度的标准试验方法

1.1 This test method covers the determination of the hoop tensile strength, including stress-strain response, of continuous fiber-reinforced advanced ceramic tubes subjected to direct internal pressurization that is applied monotonically at ambient temperature. This type of test configuration is sometimes referred to as “tube burst test.” This test method is specific to tube geometries, because flaw populations, fiber architecture, material fabrication, and test specimen geometry factors are often distinctly different in composite tubes, as compared to flat plates. 1.2 In the test method, a composite tube/cylinder with a defined gage section and a known wall thickness is loaded via internal pressurization from a pressurized fluid applied either directly to the material or through a secondary bladder inserted into the tube. The monotonically applied uniform radial pressure on the inside of the tube results in hoop stress-strain response of the composite tube that is recorded until failure of the tube. The hoop tensile strength and the hoop fracture strength are determined from the resulting maximum pressure and the pressure at fracture, respectively. The hoop tensile strains, the hoop proportional limit stress, and the modulus of elasticity in the hoop direction are determined from the stress-strain data. Note that hoop tensile strength as used in this test method refers to the tensile strength in the hoop direction from the introduction of a monotonically applied internal pressure where ‘monotonic’ refers to a continuous nonstop test rate without reversals from test initiation to final fracture. 1.3 This test method applies primarily to advanced ceramic matrix composite tubes with continuous fiber reinforcement: unidirectional (1D, filament wound and tape lay-up), bidirectional (2D, fabric/tape lay-up and weave), and tridirectional (3D, braid and weave). These types of ceramic matrix composites can be composed of a wide range of ceramic fibers (oxide, graphite, carbide, nitride, and other compositions) in a wide range of crystalline and amorphous ceramic matrix compositions (oxide, carbide, nitride, carbon, graphite, and other compositions). 1.4 This test method does not directly address discontinuous fiber-reinforced, whisker-reinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites. 1.5 The test method is applicable to a range of test specimen tube geometries based on the intended application that includes composite material property and tube radius. Lengths of the composite tube, length of the pressurized section, and length of tube overhang are determined so as to provide a gage length with uniform internal radial pressure. A wide range of combinations of material properties, tube radii, wall thicknesses, tube lengths, and lengths of pressurized section are possible. 1.5.1 This test method is specific to ambient temperature testing. Elevated temperature testing requires high-temperature furnaces and heating devices with temperature control and measurement systems and temperature-capable pressurization methods which are not addressed in this test method. 1.6 This test method addresses tubular test specimen geometries, test specimen preparation methods, testing rates (that is, induced pressure rate), and data collection and reporting procedures in the following sections: Scope Section 1 Referenced Documents Section 2 Terminology Section 3 Summary of Test Method Section 4 Significance and Use Section 5 Interferences Section 6 Apparatus Section 7 Hazards Section 8 Test Specimens Section 9 Test Procedure Section 10 Calculation of Results Section 11 Report Section 12 Precision and Bias Section 13 Keywords Section 14 Appendix References 1.7 Values expressed in this test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10. 1 This test method is under the jurisdiction of ASTM Committee C28 on Advanced Ceramics and is the direct responsibility of Subcommittee C28.07 on Ceramic Matrix Composites. Current edition approved Jan. 1, 2018. Published January 2018. Originally approved in 2018. DOI: 10.1520/C1863-18. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Hoop Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramic Composite Tubular Test Specimens at Ambient Temperature Using Direct Pressurization

ASTM B88M-18 无缝铜水管标准规范(公制)

16.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 8, an observed value or calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. 1.1 This specification covers seamless copper water tube suitable for general plumbing, similar applications for the conveyance of fluids, and commonly used with solder, flared, or compression-type fittings. The type of copper water tube suitable for any particular application is determined by the internal or external fluid pressure, by the installation and service conditions, and by local requirements. Means of joining or bending are also factors that affect the selection of the type of tube to be used.2 Note 1: Annealed tube is suitable for use with flared or compression fittings, and with solder-type fittings, provided rounding and sizing of the tube ends is performed where needed. Note 2: Drawn temper tube is suitable for use with solder-type fittings. Types A and B tube, in the drawn temper, are suitable for use with certain types and sizes of compression fittings. 1.2 The tube shall be produced from the following coppers, and the manufacturer has the option to supply any one of them, unless otherwise specified: Copper UNS No. Previously Used Designation Description  

Standard Specification for Seamless Copper Water Tube (Metric)

ASTM B626-17 焊接镍和镍钴合金管的标准规范

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Tube

ASTM B622-17 无缝镍和镍钴合金管和管的标准规范

Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

ASTM B619/B619M-17 焊接镍和镍钴合金管的标准规范

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ASTM B163-11(2017) 无缝镍和镍合金冷凝器和热交换器管的标准规范

1.1 This specification2 covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this specification are 3 in. (76.2 mm) and under in outside diameter with minimum wall thicknesses of 0.148 in. (3.76 mm) and under, and with average wall thicknesses of 0.165 in. (4.19 mm) and under. 1.3 Tube shall be furnished in the alloys and conditions as shown in Table 2. For small diameter and light wall tube (converter sizes), see Appendix X2. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes

ASTM B829-04a(2017) 镍和镍合金无缝管和管的一般要求的标准规范

1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications: Title of Specification ASTM Designation2 Nickel Seamless Pipe and Tube B161 Seamless Nickel and Nickel Alloy, Condenser and Heat Exchanger Tubes B163 Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube B165 Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and N06690) Seamless Pipe and Tube B167 Nickel-Iron-Chromium Alloy Seamless Pipe and Tube B407 Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 and N08221) Seamless Pipe and Tube B423 Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625) Pipe and Tube B444 Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy (UNS N06102) Seamless Pipe and Tube B445 Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS N08332) Seamless Pipe B535 Copper-Beryllium Alloy Forgings and Extrusion B570 Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B622 UNS N08028 Seamless Tubes B668 UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe and Tube B677 Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube B690 Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and Tube B722 Seamless UNS N08020, UNS N08026, and UNS N08024 Nickel-Alloy Pipe and Tube B729 1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

ASTM B622-17b 镍和镍钴合金无缝管和管件的标准规格

1.1 This specification2 covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N06035, UNS N06044, UNS N08135, UNS N06255, UNS N06058, UNS N06059, UNS N06200, UNS N10362, UNS N06030, UNS N08031, UNS N08034, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, UNS N06210, UNS N10624, and UNS R20033)3 as shown in Table 1. (A) See 12.1. 1.2 Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. 1.3 This specification is limited to tubes up to and including 3.5 in. (88.9 mm) outside diameter. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

ASTM B834-17 压力强化粉末冶金铁镍铬钼(UNS N08367), 镍铬钼钶(Nb)(UNS N06625), 镍铬铁合金(UNS N06600和N06690)以及镍铬铁库仑的标准规格

1.1 This specification covers pressure consolidated powder metallurgy iron-nickel-chromium-molybdenum (UNS N08367) and nickel-chromium-molybdenumcolumbium (Nb) (UNS N06625), nickel-chromium-iron alloys (UNS N06600 and N06690), and nickel-chromium-iron-columbium (Nb)-molybdenum (UNS N07718) alloy pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service. 1.1.1 UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1 (annealed)—Material is normally employed in service temperatures up to 1100°F (593°C). 1.1.1.2 Grade 2 (solution annealed)—Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required. 1.2 UNS N08367 products are furnished in the solution annealed condition. 1.3 UNS N06600 products are furnished in the annealed condition. 1.4 UNS N06690 products are furnished in the annealed condition. 1.5 UNS N07718 products are furnished in the solution annealed + precipitation hardened condition. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 The following safety hazards caveat pertains only to test methods portions, Sections 7.3 and 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and to determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Colum

ASTM B619/B619M-17b 焊接镍和镍钴合金管的标准规格

1.1 This specification2 covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06044; UNS N06058; UNS N06059; UNS N06200; UNS N10362; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N08034; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)3 as shown in Table 1. (A) The composition of the remainder shall be determined arithmetically by difference. 1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2). (A) Schedules 5S and 10S wall thicknesses do not permit threading in accordance with ANSI B2.1-1960. 1.3 Two classes of pipe are covered as follows: 1.3.1 Class I—As welded and solution annealed or welded and sized and solution annealed. 1.3.2 Class II—Welded, cold worked, and solution annealed. 1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ASTM A807/A807M-17 下水道及其它类似用途用波纹结构钢涂覆管安装的标准实施规程

4.1 Structural plate structures function structurally as a flexible ring that is supported by and interacts with the compacted surrounding soil. The soil placed around the structure is thus an integral part of the structural system. It is therefore important to ensure that the soil structure is made up of acceptable material and is well constructed. Field verification of soil structure acceptability using Test Methods D1556, D2167, D6938, or D2937, as applicable, and comparing the results with either Test Methods D698 or D1557, in accordance with the specifications for each project, is the most common basis for installation of an acceptable structure. Depending on the backfill used, other qualitative or performance-based methods acceptable to the engineer may also be used. The required density and method of measurement are not specified by this practice, but must be established in the specifications for each project. 4.2 Structural plate structures are also occasionally used in alternative applications not requiring soil-structure interaction for support. Depending on the application the structure may provide temporary or permanent support, confinement, concealment, shielding, or other functions not related to soil-structure interaction. The nature of support required, design requirements, and proper sizing of the structure will be determined by a project design engineer and is not part of the scope of this standard. 1.1 This practice primarily covers procedures, soils, and soil placement for the proper installation of corrugated steel structural plate pipe, pipe-arches, arches, and underpasses produced to Specification A761/A761M, in either trench or embankment installations. This practice also covers installation of structural plate for alternative uses that do not involve backfilling or soil-structure interaction. 1.2 A typical trench installation and a typical embankment (projection) installation are shown in Figs. 1 and 2, respectively. Structural plate structures as described herein are those structures factory fabricated in plate form and bolted together on site to provide the required shape, size, and length of structure. This practice applies to structures designed in accordance with Practice A796/A796M. FIG. 1 Typical Trench Installation FIG. 2 Typical Embankment (Projection) Installation 1.3......

Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications

ASTM B135/B135M-17 无缝黄铜管的标准规格

1.1 This specification covers seamless round and rectangular including square copper alloy tube in straight lengths. Ten alloys are specified having the following nominal compositions: Copper Previously Nominal Composition, % Alloy Used         UNS No.2 DesignationA Copper Zinc Lead Tin           C22000 7 90.0 10.0 ... ... C23000 1

Standard Specification for Seamless Brass Tube