23.040.15 有色金属管 标准查询与下载

GSO ASTM B447:2015 焊接铜管标准规范

This specification establishes the requirements for welded copper tube with a longitudinal seam free of filler metal produced from sheet or strip of one of the Copper UNS Nos. C10100, C10200, C10300, C10800, C11000, C12000, C12200, and C14200. Copper C11000 welded tube shall not be used in applications where hydrogen embrittlement during heating is a concern. Tempers of the welded tube types are as follows: as-welded: WM50, WM02, or WM04, welded and annealed: W060 and W050, welded and cold drawn: WH00, WH02, and WH04, and fully finished: O60, O50, H55, H58, and H80. The product shall be manufactured by forming the material into a tubular shape on a suitable forming mill and welding shall be accomplished by any process that produces forge or fusion welds. The external flash of forge welded tube shall be removed by scarfing and the internal flash shall be treated by IFI (to remain in the as-welded condition), IFR (scarfing) or IFD (rolling or drawing) technique. The material shall conform to the chemical composition requirements prescribed for copper, phosphorus, and arsenic, as determined by chemical analysis. The welded tubes shall meet the requirements specified for grain size, electrical mass resistivity, mechanical properties such as tensile strength and Rockwell hardness, dimensions, and mass. Performance requirements includes microscopical examination, hydrogen embrittlement susceptibility test, and expansion test. Requirements for tensile, electromagnetic (eddy-current), hydrostatic, and pneumatic tests are detailed. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Standard Specification for Welded Copper Tube

DIN EN 13480-8/A2:2015 工业用金属管道.第8部分:铝及铝合金管的附加要求;德文版本EN 13480-8-2012/A2-2015

Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping; German version EN 13480-8:2012/A2:2015

GSO ISO 6207:2015 无缝镍及镍合金管

1.1 This International Standard specifies requirements for round seamless nickel and nickel alloy tube for general purposes as well as for condenser and heat-exchanger applications in the following size ranges. 1.1.1 Tube for general purposes Cold worked: outside diameter 4 mm to 240 mm Hot worked: outside diameter 38 mm to 240 mm 1.1.2 Tube for condenser and heat-exchanger applications Cold worked: maximum outside diameter 80 mm with wall thickness up to and including 5 mm. 1.2 Dimensional requirements and limiting bend radii are also specified for U-bent heat-exchanger tubes of outside diameter up to and including 26 mm.

Seamless nickel and nickel alloy tube

GSO ISO 7773:2015 镁合金圆棒和管材尺寸公差

This International Standard specifies dimensional tolerances for round bars and tubes made from magnesium alloys. The products may be manufactured from any wrought magnesium alloys, especially the magnesium-aluminium-zinc alloys and the magnesium-zirconium-zinc alloys specified in ISO 31161).

Magnesium alloys -- Round bars and tubes -- Dimensional tolerances

EN 13480-8:2012/A2:2015 工业金属管道.第8部分:铝和铝合金管道的附加要求

Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping

GOST 16774-2015 矩形和方形型材的铜管. 规格

Copper tubes of rectangular and square sections. Specifications

ASTM B626-15 焊接镍和镍钴合金管的标准规格

1.1 This specification covers welded tubes made from the nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10629, UNS N10624, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N06975, UNS N08320, UNS N06985, UNS N06002, UNS N06022, UNS N06030, UNS N06035, UNS N06058, UNS N06059, UNS N06200, UNS N06617, UNS N10362, UNS N06210, UNS N08031, UNS R30556, UNS N06230, UNS N06686, and UNS R20033)2 listed in Table 1 intended for heat exchanger and condenser tubes and tubes for general corrosive service for heat-resisting applications. 1.2 This specification covers tube 1/8 to 31/2 in. (3.2 to 88.9 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive, in wall thickness. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Tube

ASTM B983-15 沉淀硬化或者冷加工无缝镍合金管的标准规格

1.1 This specification covers high strength, seamless pipe and tube of nickel alloys (UNS N07022, UNS N07725, UNS N07740, UNS N09945, UNS N09925, UNS N07718, UNS N10276, UNS N06985)2 as shown in Table 1. (A) Minimum: The element may be determined arithmetically by difference.(B) Remainder: The element may be determined arithmetically by difference. 1.2 Pipe and tube shall be supplied in the cold worked or cold worked and precipitations hardened or solution annealed plus precipitation hardened and descaled conditions. When atmosphere control is used, descaling is not necessary. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube

ASTM B903-15 内部增强型无缝铜制换热器管的标准规格

1.1 This specification establishes the requirements for seamless, internally enhanced copper tube, in straight lengths or coils, suitable for use in refrigeration and air-conditioning products or other heat exchangers. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 Tubes for this application are manufactured from the following copper: Copper UNS No. Type of Metal     C12200 Phosphorized, high residual phosphorus (DHP) 1.4 The following pertains to the test method described in 15.2.4 of this specification: This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless Copper Heat Exchanger Tubes With Internal Enhancement

ASTM B619/B619M-15 焊接镍和镍钴合金管的标准规格

1.1 This specification2 covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N10362; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)3 as shown in Table 1. (A) The composition of the remainder shall be determined arithmetically by difference. 1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2). (A) Schedules 5S and 10S wall thicknesses do not permit threading in accordance with ANSI B2.1-1960. 1.3 Two classes of pipe are covered as follows: 1.3.1 Class I—As welded and solution annealed or welded and sized and solution annealed. 1.3.2 Class II—Welded, cold worked, and solution annealed. 1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

ASTM B360-15 限制器应用使用冷拉铜毛细管的标准规格

1.1 This specification establishes the requirements for hard-drawn, seamless capillary tube made from Copper Alloy UNS Nos. C10800, C12000, or C12200. 1.2 This tube is commonly supplied in straight lengths intended for restrictor applications such as metering lines for liquids and gases where close control over smoothness and diameter of the bore is required to insure uniform flow characteristics between tubes. 1.3 Units—The values stated in inch pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Hard-Drawn Copper Capillary Tube for Restrictor Applications

ASTM B359/B359M-15 冷凝器及热交换器使用带整体翅片的无缝铜和铜合金管的标准规格

1.1 This specification2 establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer. 1.2 The tubes are typically used in surface condensers, evaporators, and heat exchangers. 1.3 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information. Copper or Copper Alloy UNS No. Type of Metal     C10100 Oxygen-free electronic C10200 Oxygen-free without residual deoxidants C10300 Oxygen-free, extra low phosphorus C10800 Oxygen-free, low phosphorus C12000 DLP Phosphorized, low residual phosphorus (See Note 1) C12200 DHP, Phosphorized, high residual phosphorus (See Note 1) C14200 DPA Phosphorized arsenical (See Note 1) C19200 Phosphorized, 18201;% iron C23000 Red Brass

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

ASTM B491/B491M-15 一般用途铝和铝合金模压圆管的标准规格

1.1 This specification covers aluminum and aluminum-alloy extruded round tubes either in coils or straight lengths, for general purpose applications such as refrigeration service, gas lines, oil lines, and instrument lines, in the alloys (Note 2) and tempers shown in Table 2 [Table 3], in outside diameters of 0.250 through 0.750 in. [6.00 through 20.008201;mm]. For diameters over 0.500 through 0.750 in. [over 12.50 through 20.008201;mm], the diameter and wall-thickness tolerances and eddy-current test parameters, if required, shall be agreed upon by the producer and the purchaser. Only tubes in aluminum 1200-H111 and 1235-H111 are sized after extrusion to minimize ovalness. (A) Limits are in percent maximum unless shown as a range or otherwise stated.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded off to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.0108201;% or more, rounded to the second decimal before determining the sum.(F) The aluminum content shall be calculated by subtracting from 100.008201;% the sum of all metallic elements present in amounts of 0.0108201;% or more each, rounded to the second decimal before determining the sum.(G) Vanadium 0.05%, maximum.

Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications

GSO ISO 6363-1:2014 锻造铝及铝合金 棒/柱、冷拔管及线材 第1部分：检验和交货技术条件

This part of ISO 6363 specifies the technical conditions for the inspection and delivery of wrought aluminium and aluminium alloys rods/bars, tubes and wires for general engineering applications. It applies to products which are extruded and then cold drawn. It does not apply to: — products which are rolled and then cold drawn, including seam-welded tubes; — forging stock, wire for drawing stock; — drawn wires for aeronautical application, electrical or welding purposes.

Wrought aluminium and aluminium alloys -- Cold-drawn rods/bars, tubes and wires -- Part 1: Technical conditions for inspection and delivery

GSO ISO 6362-2:2014 成型铝和铝合金棒材/柱材、管材和挤压型材 第2部分：机械性能

This part of ISO 6362 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded products.

Wrought aluminium and aluminium alloys -- Extruded rods/bars, tubes and profiles -- Part 2: Mechanical properties

GSO ISO 6362-1:2014 成型铝和铝合金棒材/柱材、管材和挤压型材 第1部分：检验和交货技术条件

This part of ISO 6362 specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy rods/bars, tubes and profiles for general engineering applications. It applies to extruded products, but does not apply to the following: — forging stock; — extruded precision profiles in alloys A6060 and A6063; — products delivered in coils; — coiled tubes cut to lengths

Wrought aluminium and aluminium alloys -- Extruded rods/bars, tubes and profiles -- Part 1: Technical conditions for inspection and delivery

GSO ISO 6363-2:2014 锻造铝和铝合金 冷拔棒/柱、管和线材 第2部分：机械性能

This part of ISO 6363 specifies the mechanical properties of wrought aluminium and aluminium alloy rods/bars, tubes and wires for general engineering applications (except aeronautical rivets). It applies to products which are extruded and then cold drawn. It does not apply to: — products which are rolled and then cold drawn, including seam-welded tubes; — forging stock, wire for drawing stock; — drawn wires for aeronautical application, electrical or welding purposes.

Wrought aluminium and aluminium alloys -- Cold-drawn rods/bars and tubes and wires -- Part 2: Mechanical properties

DIN EN 13480-8:2014 工业用金属管道. 第8部分:铝及铝合金管的附加要求; 德文版本EN 13480-8-2012

Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping; German version EN 13480-8:2012

NF E86-700-8/A1:2014 工业用金属管道. 第8部分: 铝和铝合金管的附加要求

Metallic industrial piping - Part 8 : additionnal requirements for aluminium and aluminium alloys piping

ASTM B88-14 无缝铜水管的标准规格

16.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 8, an observed value or calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. 1.1 This specification establishes the requirements for seamless copper water tube suitable for general plumbing, similar applications for the conveyance of fluids, and commonly used with solder, flared, or compression-type fittings. The type of copper water tube suitable for any particular application is determined by the internal or external fluid pressure, by the installation and service conditions, and by local requirements. Means of joining or bending are also factors which affect the selection of the type of tube to be used.2 Note 1: Annealed tube is suitable for use with flared or compression fittings, and with solder-type fittings, provided rounding and sizing of the tube ends is performed where needed. Note 2: Drawn temper tube is suitable for use with solder-type fittings. Types K and L tube, in the drawn temper, are suitable for use with certain types and sizes of compression fittings. Note 3: Fittings used for soldered or brazed connections in plumbing systems are described in ASME B16.18 and ASME B16.22. 1.2 The tube shall be produced from the following coppers, and the manufacturer has the option to supply any one of them, unless otherwise specified. Copper UNS No. Previously Used Designation Description  

Standard Specification for Seamless Copper Water Tube