23.040.15 有色金属管 标准查询与下载

GOST 20900-2014 波导用铜管以及直角黄铜管. 规格

Copper tubing for waveguides and brass right angle tubes. Specifications

GOST 494-2014 黄铜管. 规格

Brass tubes. Specifications

GOST 1208-2014 压制青铜管. 规格

Pressed bronze tubes. Specifications

KS D ISO 6207:2013 无缝镍管和镍合金管

Seamless nickel and nickel alloy tube

DIN EN 13480-8:2013 工业用金属管道. 第8部分:铝及铝合金管的附加要求; 德文版本EN 13480-8-2012

Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping; German version EN 13480-8:2012

ASTM A807/A807M-13 用于下水道和其他应用安装波纹钢结构板管的标准实践

4.1 Structural plate structures function structurally as a flexible ring that is supported by and interacts with the compacted surrounding soil. The soil placed around the structure is thus an integral part of the structural system. It is therefore important to ensure that the soil structure is made up of acceptable material and is well constructed. Field verification of soil structure acceptability using Test Methods D1556, D2167, D6938, or D2937, as applicable, and comparing the results with either Test Methods D698 or D1557, in accordance with the specifications for each project, is the most common basis for installation of an acceptable structure. Depending on the backfill used, other qualitative or performance-based methods acceptable to the engineer may also be used. The required density and method of measurement are not specified by this practice, but must be established in the specifications for each project. 1.1 This practice covers procedures, soils, and soil placement for the proper installation of corrugated steel structural plate pipe, pipe-arches, arches, and underpasses produced to Specification A761/A761M, in either trench or embankment installations. A typical trench installation and a typical embankment (projection) installation are shown in Figs. 1 and 2, respectively. Structural plate structures as described herein are those structures factory fabricated in plate form and bolted together on site to provide the required shape, size, and length of structure. This practice applies to structures designed in accordance with Practice A796/A796M. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 The values stated in either inch-pound units or SI units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. SI units are shown in brackets in the text for clarity, but they are the applicable values when the installation is to be performed using SI units.

Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications

ASTM B834-13 压力固结粉末冶金铁镍 - 铬钼（UNS N08367）和镍 - 铬 - 钼 - 铌（Nb）（UNS N06625）合金管法兰 配件 阀门和部件的标准规范

1.1 This specification covers pressure consolidated powder metallurgy iron-nickel-chromium-molybdenum (UNS N08367) and nickel-chromium-molybdenumcolumbium (Nb) (UNS N06625) pipe flanges, fittings, valves, and parts intended for general corrosion or heat-resisting service. 1.1.1 UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1 (annealed)—Material is normally employed in service temperatures up to 1100°F (593°C). 1.1.1.2 Grade 2 (solution annealed)—Material is normally employed in service temperatures above 1100°F (593°C) when resistance to creep and rupture is required. 1.2 UNS N08367 products are furnished in the solution annealed condition. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to test methods portions, Sections 7.3 and 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and to determine the applicability of regulatory limitations prior to use.

Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367) and Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625) Alloy Pipe Flanges, Fittings,

GOST 32590-2013 铜管毛细管钎焊法或铜焊法用端头的铜和铜合金接头. 规格

Fittings of copper and copper alloys with ends for capillary soldering or capillary brazing to copper tubes. Specifications

ASTM B811-13(2017) 核反应堆燃料包壳用锻制锆合金无缝管的标准规格

1.1 This specification covers seamless wrought zirconium-alloy tubes for nuclear fuel cladding application, in the outside diameter (OD) size range of 0.200 in. (5.1 mm) to 0.650 in. (16.5 mm) and wall thickness range of 0.010 in. (0.25 mm) to 0.035 in. (0.89 mm). 1.2 Two grades of reactor grade zirconium alloys are described. 1.2.1 The present UNS numbers designated for the two grades are given in Table 1. 1.3 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.4 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Wrought Zirconium Alloy Seamless Tubes for Nuclear Reactor Fuel Cladding

ASTM B483/B483M-13e1 一般用途的铝和铝合金冷拔管和拉制管的标准规格

1.1 This specification covers aluminum and aluminum-alloy drawn tube and drawnpipe in straight lengths and tube in coils for general purpose applications in the alloys (Note 2), and tempers shown in Tables 1 and 2. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys.Note 1—For drawn seamless tubes, see Specifications B210 and B210M, for tubes to be used in condensers and heat exchangers, Specifications B234 and B234M, and for seamless pipe, Specification B241/B241M. For extruded structural tube and pipe, see Specification B429.Note 2—this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Number System alloy designations are those of Table 3 preceded by A9, for example A91060 for aluminum 1060 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications

GOST 32598-2013 水和气用管铜轮. 规格

Tubes copper tubes for water and gas. Specifications

GOST 32591-2013 用于铜管的压缩终端铜和铜合金接头. 规格

Fittings of copper and copper alloys with compression ends for use with copper tubes. Specifications

GOST 32585-2013 管道连接用铜和铜合金配件适配器. 规格

Fittings-adapters from copper and copper alloys for connecting of pipelines. Specifications

EN 13480-8:2012 金属工业管道.第8部分:铝及铝合金管道额外要求

This Part of this European Standard specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480:2012 and CEN/TR 13480-7:2002.

Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping

ASTM B359/B359M-12e1 具有整体散热叶片的冷凝器及热交换器用铜及铜合金无缝管标准规格

1.1 This specification2 establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer. 1.2 Units—The values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification. 1.3 The tubes are typically used in surface condensers, evaporators, and heat exchangers. 1.4 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information. Copper or Copper Alloy UNS No. Type of Metal     C10100 Oxygen-free electronic C10200 Oxygen-free without residual deoxidants C10300 Oxygen-free, extra low phosphorus C10800 Oxygen-free, low phosphorus C12000 DLP Phosphorized, low residual phosphorus (See Note 1) C12200 DHP, Phosphorized, high residual phosphorus (See Note 1) C14200 DPA Phosphorized arsenical (See Note 1) C19200 Phosphorized, 18201;% iron C23000 Red Brass C44300 Admiralty Metal Types B,

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

GSO EN 1057:2011 铜及铜合金 水、煤气、卫生和供热用无缝圆形铜管

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes. It is applicable to tubes having an outside diameter from 6 mm up to and including 267 mm for: - distributing networks for hot water and cold water; - hot water heating systems, including panel heating systems (under-floor, wall, overhead); - domestic gas and liquid fuel distribution; - waste water sanitation. It is also applicable to seamless round copper tubes intended to be pre insulated before use for any of the above purposes.

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications

NF A51-126-2:2011 铜和铜合金.空气调节和制冷用无缝圆铜管.第2部分:设备用管.

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2 : tubes for equipment.

NF A51-126-1:2011 铜和铜合金.空气调节和制冷用无缝圆铜管.第1部分:管路系统用管

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1 : tubes for piping systems.

ASTM B423-11(2016) 镍铁铬钼铜合金 (UNS N08825, N08221和N06845) 无缝管的标准规格

1.1 This specification2 covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825, N08221, and N06845)3 in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. The general requirements for pipe and tube are covered in Specification B829. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825, N08221, and N06845) Seamless Pipe and Tube

ASTM B153-11(2017) 铜和铜合金管膨胀(针试验)的标准试验方法

5.1 When properly performed and interpreted, the expansion pin test will provide information with regard to the capacity of a tube for expansion and to reveal surface defects. The expansion pin test may provide data for research and development, engineering design, quality control, and acceptance or rejections in specifications. 5.2 In certain product specifications which establish requirements for tubes of sizes greater than 4 in. (102 mm), the test described in Test Method B968/B968M may be allowed as a substitute. 1.1 This test method establishes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing with an inside diameter of 0.125 in. (3.2 mm) and greater or an outside diameter up to and including 4 in. (102 mm). Note 1: For tubes of sizes with an inside diameter less than 0.125 in. (3.2 mm), a substitute test method must be agreed upon between the manufacturer and purchaser. Note 2: For tubes of sizes greater than 4 in. (102 mm) in outside diameter, refer to B968/B968M for a test method. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing