23.040.15 有色金属管 标准查询与下载

GOST R 54568-2011 合金MNZh5-1管.规格

Tubes from alloy MNZH5-1. Specifications

ASTM B658/B658M-11 无缝和焊接锆和锆合金管标准规格

1.1 This specification covers three grades of seamless and welded zirconium pipe. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test methods portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe

ASTM B153-11 铜和铜合金管膨胀(针试验)的标准试验方法

When properly performed and interpreted, the expansion pin test will provide information with regard to the capacity of a tube for expansion and to reveal surface defects. The expansion pin test may provide data for research and development, engineering design, quality control, and acceptance or rejections in specifications. In certain product specifications which establish requirements for tubes of sizes greater than 4 in. (102 mm), the test described in B968/B968M may be allowed as a substitute.1.1 This test method establishes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing with an inside diameter of 0.125 in. (3.2 mm) and greater or an outside diameter up to and including 4 in. (102 mm). Note 18212;For tubes of sizes with an inside diameter less than 0.125 in. (3.2 mm), a substitute test method must be agreed upon between the manufacturer and purchaser. Note 28212;For tubes of sizes greater than 4 in. (102 mm) in outside diameter, refer to B968/B968M for a test method. 1.2 Units8212;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing

ASTM B658/B658M-11(2016) 无缝和焊接的锆和锆合金管的标准规格

1.1 This specification2 covers three grades of seamless and welded zirconium pipe. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test methods portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe

DIN EN 12735-1:2010 铜和铜合金.空气调节和制冷用无缝圆形铜管.第1部分:管道系统用管.德文版本EN 12735-1-2010

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems; German version EN 12735-1:2010

DIN EN 12735-2:2010 铜和铜合金.空气调节和制冷用无缝圆形铜管.第2部分:设备用管.德文版本EN 12735-2-2010

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2: Tubes for equipment; German version EN 12735-2:2010

LST EN 12735-1-2010 铜和铜合金 空调和制冷用无缝圆铜管 第1部分：管道系统用管

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems

LST EN 12735-2-2010 铜和铜合金 空调和制冷用无缝圆铜管 第2部分：设备用管

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2: Tubes for equipment

ASTM B828-02(2010) 通过铜铜合金管和配件焊接制造毛细管接头的标准实践

Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings

ASTM B135-10 无缝铜管标准规范

1.1 This specification covers seamless round and rectangular including square copper alloy tube in straight lengths. Ten alloys are specified having the following nominal compositions:

Standard Specification for Seamless Brass Tube

EN 12735-2:2010 铜和铜合金.空气调节和制冷用无缝圆形铜管.第2部分:设备用管

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes, smooth or inner finned, used for heat exchangers and their internal connecting pipes in the manufacturing of refrigeration and air conditioning equipment. It is applicable to tubes with an outside diameter from 6 mm up to and including 133 mm. The tubes are supplied in straight length in the material conditions hard, half-hard or skin hard or as coils in the material conditions light annealed or soft annealed.

Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2: Tubes for equipment

LST EN 1057-2006+A1-2010 铜和铜合金 卫生和供暖应用中用于水和气体的无缝圆形铜管

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications

DIN EN 1057:2010 铜和铜合金.在卫生和加热器中输送水和气体用无缝圆铜管.德文版本EN 1057-2006+A1-2010

This European Standard specifies the requirements, sampling ,test methods and conditions of delivery for seamless round copper tubes.

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications; German version EN 1057:2006+A1:2010

NF A51-120*NF EN 1057+A1:2010 铜和铜合金.公共厕所和采暖设施中供水供气用无缝圆形铜管

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications.

EN 1057:2006+A1:2010 铜和铜合金.卫生设备和水加热器的水和气体用无缝圆铜管

This European Standard specifies the requirements, sampling, test methods and conditions of delivery for seam- less round copper tubes. It is applicable to tubes having an outside diameter from 6 mm up to and including 267 mm for: distributing networks for hot water and cold water; hot water heating systems, including panel heating systems (under-floor, wall, overhead); domestic gas and liquid fuel distribution; waste water sanitation. It is also applicable to seamless round copper tubes intended to be pre-insulated before use for any of the above purposes.

Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications

ASTM B698-10 无缝铜和铜合金管和管道的标准分类

This classification is provided to serve the needs of designers, specifiers, installers, and users of seamless copper and copper alloy plumbing tube and piping systems. It familiarizes them with the products available for such systems, giving size ranges and available materials for products listed herein. Also refer to Section 1.1.1 This classification covers various types of seamless copper and copper alloy pipe and tube used for water service, distribution, and drainage. It is not a specification for the various types and alloys. 1.2 This classification uses the standard copper designations developed and used by the copper industry. 1.3 This classification makes no attempt to differentiate between all compositions that could be termed coppers or copper alloys, but, in conformance with general practice in the trade includes those coppers and copper alloys commonly used in the manufacture of water service, distribution, and drainage pipe and tube. 1.4 This classification makes no attempt to differentiate between all applications of seamless copper and copper alloy piping and tube intended for use in water service distribution and drainage.

Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube

GOST R 54158-2010 铜域铜合金制薄壁管.规范

Thin-walled tubes from copper and copper alloys. Specifications

ASTM B626-10 焊接镍和镍钴合金管的标准规格

1.1 This specification covers welded tubes made from the nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10629, UNS N10624, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N06975, UNS N08320, UNS N06985, UNS N06002, UNS N06022, UNS N06030, UNS N06035, UNS N06058, UNS N06059, UNS N06200, UNS N10362, UNS N06210, UNS N08031, UNS R30556, UNS N06230, UNS N06686, and UNS R20033)* listed in Table 1 intended for heat exchanger and condenser tubes and tubes for general corrosive service for heat-resisting applications. 1.2 This specification covers tube 1/8 to 3½ in. (3.2 to 88.9 mm) in outside diameter and 0.015 to 0.148 in. (0.41 to 3.7 mm) inclusive, in wall thickness. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Tube

ASTM B619-10 焊接的镍和镍钴合金管的标准规格

1.1 This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320; UNS N06002; UNS N06022; UNS N06035; UNS N06058; UNS N06059; UNS N06200; UNS N06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)* as shown in Table 1. 1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forth in ANSI B36.19 (see Table 2).1.3 Two classes of pipe are covered as follows:1.3.1 Class IAs welded and solution annealed or welded and sized and solution annealed.1.3.2 Class II Welded, cold worked, and solution annealed.1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe

GSO ASTM B302:2009 非合金铜管的标准规格 标准尺寸

1.1 This specification establishes requirements for threadless, seamless, deoxidized copper pipe (TP) in straight lengths, in all nominal or standard pipe sizes, for piping systems that are assembled with brazed-joint pipe fittings. The pipe shall be produced from either of coppers UNS Nos. C10300 or C12200. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described Section 16 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Standard Specification for Threadless Copper Pipe, Standard Sizes