23.040.80 管和软管组件的密封件 标准查询与下载

BS EN 1514-2:2014 法兰和其接头. 指定PN的法兰垫片. 钢制法兰用螺旋形垫片

Flanges and their joints. Gaskets for PN-designated flanges. Spiral wound gaskets for use with steel flanges

EN 1514-2:2014 法兰及其连接件.PN-标示的法兰用衬垫的尺寸.第2部分:钢法兰用螺旋形衬垫

This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1000. NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, EN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 and EN 1514-8. NOTE 2 Annex A lists information to be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the manufacturer.

Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges

ASTM F477-14 连接塑料管的弹性体密封件 (垫片) 的标准规格

1.1 This specification covers elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications. This refers to push-on joints which require no internal or external pressure to effect the initial seal. 1.2 Requirements are given for natural or synthetic rubber gaskets, or a combination of both. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

ASTM F493-14 氯化聚氯乙烯 (CPVC) 塑料管及配件用溶剂粘结剂的标准规格

1.1 This specification provides requirements for chlorinated poly(vinyl chloride) (CPVC) solvent cements to be used in joining chlorinated poly(vinyl chloride) pipe, tubing, and socket-type fittings. 1.2 CPVC solvent cements are used with CPVC 41 chlorinated poly(vinyl chloride) pipe, tubing, and fittings, which meet Class 23447 as defined in Specification D1784. 1.3 A recommended procedure for joining CPVC pipe and fittings is given in Appendix X1. 1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: 8201; This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings

GOST 32935-2014 热网用钢波纹膨胀节. 通用规格

Steel bellows expansion joints for heat networks. General specifications

KS B ISO 7483:2013 符合ISO 7005标准的法兰密封垫圈的尺寸

Dimensions of gaskets for use with flanges to ISO 7005

DIN EN 12560-2:2013 法兰及其接头.分级标识法兰用垫圈的尺寸.第2部分:钢法兰用绕制螺旋形密封垫.德文版本EN 12560-2-2013

Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges; German version EN 12560-2:2013

EN 12560-2:2013 法兰及其连接件.法兰用垫片(英制).第2部分:钢制法兰用螺旋缠绕垫片

This European Standard specifies the dimensions, design, types, designation, materials and marking of spiral wound gaskets for use with type A flat face or type B raised face flange facings complying with EN 1759-1 for the following Class designations: Class 150, to Class 1500 for nominal sizes DN 15 to DN 600, and Class designation 2500 up to and including DN 300. The centering rings for the spiral wound gaskets according to this standard are sized for use with imperial bolting. The dimensions of spiral wound gaskets for tongue and groove flange facing types and spigot and recess flange facing types to EN 1759-1 are not included in this standard. Such gaskets may be available, however, for these types of flange and the purchaser is advised to consult the manufacturer as to their availability. Similarly, for slip-on or screwed flange types, the manufacturer should be consulted about availability. NOTE Dimensions of other types of gasket for use with flanges complying with the requirements of EN 1759-1 are given in EN 12560-1, EN 12560-3, EN 12560-4 and EN 12560-5, EN 12560-6 and EN 12560-7.

Flanges and their joints - Dimensions of gaskets for Classdesignated flanges - Part 2: Spiral wound gaskets for use with steel flanges

SAE J1453-2-2013 O型密封圈端面密封管接头规格:第2部分:钢管接头、防水壁、旋转接头、铜焊管接头、封闭盖和ISO 6149-2标准公制螺柱端连接管接头的要求、尺寸和试验

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-2 covers the requirements for ""metric based"" O-ring face seal connectors to metric stud ends along with the associated adapters, bulkhead and union connectors. Metric hex wrenching flats are used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 2 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Braze-on Tube Ends, Caps, and Connectors with ISO 6149-2 Metric Stud Ends and ISO 6162 4-Bolt Flange Heads

SAE J1453/3-2012 O形环密封面连接器规范.第3部分:钢管接头,壁板,转环,钎套,连接器,帽盖和SAE J 1926-2标准英制螺杆端连接器尺寸规格,试验和要求

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers the requirements for "inch based" O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex wrenching flats are predominantly used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 3 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J 1926-2 Inch Stud Ends

SAE J1453-1-2012 O形面密封连接器的规格: 第1部分. 管路连接详情和通用性能和试验要求

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 50 mm.

Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests

ASTM F2946-12(2017) 塑料管连接现场管道和检修孔使用聚氯乙烯(PVC)衬套和弹性体密封(垫圈)三通接头的标准规格

1.1 This specification covers the minimum performance and material requirements for a three piece tee connector for connection between plastic pipe and insitu pipes, manholes and wastewater structures in sanitary and storm sewer applications. 1.1.1 The three piece seal system consists of a 4 through 30-in. PVC (polyvinyl chloride) hub pipe, an elastomeric seal (gasket) and a mechanical band (Fig. 1). The system is installed in either a bored or cast hole opening in the host pipe or structure to a specific dimension that corresponds to the combined diameter of the PVC pipe outside diameter/tolerance and the elastomeric seal thickness. FIG. 1 Three-Piece Sealing System (Connector) 1.2 These tee connectors are designed to provide a non-pressure (gravity flow) watertight connection between the incoming pipe and an insitu pipe or manhole/structure to the limits defined in this standard. Note 1: Connections covered by this specification are adequate for laboratory hydrostatic pressures up to 13 psi (30 ft of head) without leakage when tested in accordance with the provisions of this standard. Infiltration or exfiltration quantities for an installed system are dependent upon many factors other than the connections between incoming pipe and the insitu pipe or manhole structure, and allowable quantities may need to be covered by other specifications and suitable testing of the installed pipeline and system. Where connections are made to concrete manhole sections refer to Specification C923. Note 2: These connectors are not resilient connectors, and as such, allow for only a limited amount of lateral movement due to the tight compression seal between the PVC hub and insitu pipe/structure. Since these connectors are not rigid fittings, a significant amount of axial movement can be accommodated, but the degree of intrusion into the host pipe/structure must be regulated to minimize the impact on flow characteristics or hydraulic design conditions. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see Section 7. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for t

Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes

ANSI/ASTM F2946:2012 连接塑料管和现场管道及检修孔用聚氯乙烯(PVC)集线器和弹料密封(GASKET)三通接头规格

SPECIFICATION FOR PVC HUB AND ELASTOMERIC SEAL (GASKET) TEE CONNECTION FOR JOINING PLASTIC PIPE TO INSITU PIPELINES AND MANHOLES

ANSI/ASME B16.20-2012 管法兰用金属垫圈(环形接头、螺旋缠绕和有套的)

Metallic Gaskets for Pipe Flanges (Ring-Joint, Spiral-Wound, and Jacketed)

ANSI/AWWA C111/A21.11-2012 球墨铸铁压力管和配件用橡胶垫接头

This standard describes rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for potable water, wastewater and reclaimed water supply service.

Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings

ASME B16.20-2012 管道法兰的金属衬垫:环状接头,螺旋状缠绕和套状密封

Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed

JC/T 2052-2011 辊压法无石棉纤维垫片材料

本标准规定了辊压法无石棉纤维垫片材料（以下简称"垫片材料"）的分类和标记、要求、试验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于以不含有石棉成分的纤维为主要增强材料、以弹性体为粘合剂和辅助增强材料，再添加其他填料，经辊压而制成的用于制作密封垫片的板材。用这种板材制成的密封垫片也可参照执行。

Compressed non-asbestos fibre gasket materials

KS M 6705-2011 轮胎和管修理用橡胶

이 표준은 타이어 재생 및 튜브 수리에 사용하는 재작업 고무(이하 재작업 고무라 한다.)에

Reparing rubber for tires and tubes

GSO EN 681-1:2011 柔性密封件 水和废水应用中使用的管接头密封件的材料要求 第1部分：硫化橡胶

This standard specifies requirements for materials used in vulcanized rubber seals for: a) cold potable water supply (up to 45°C); 2) hot potable and non-potable water supply (up to 110°C); 3) drainage, sewerage and rainwater systems (continuous flow up to 45°C and intermittent flow up to 95°C). The different designations of seals specified are defined according to their type, application and requirements.

Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber

ANSI/ASTM F2331:2011 测定热塑性螺纹管和配件材料的螺纹密封件的化学兼容性的试验方法

Test Method For Determining Chemical Compatibility Of Thread Sealants With Thermoplastic Threaded Pipe And Fittings Materials