23.040.80 管和软管组件的密封件 标准查询与下载

DIN 3535-6:2011 供气用密封垫.第6部分:气阀,煤气设备和煤气主管道用基于合成纤维,石墨或聚四氟乙烯(PTFE)的密封垫材料

Gaskets for gas supply - Part 6: Gasket materials based on fibres, graphite or polytetrafluoroethylene (PTFE) for gas valves, gas appliances and gas mains

ASME B16.21-2011 管法兰用非金属平垫圈

This Standard covers types, sizes, materials, dimensions, tolerances, and markings for nonmetallic flat gaskets. These gaskets are dimensionally suitable for use with flanges described in the referenced flange standards.

Nonmetallic Flat Gaskets for Pipe Flanges (B16.21 - 2011)

ANSI/ASME B16.21-2011 管法兰用非金属平垫圈

This Standard covers types, sizes, materials, dimensions, tolerances, and markings for nonmetallic flat gaskets. These gaskets are dimensionally suitable for use with flanges described in the referenced flange standards.

Nonmetallic Flat Gaskets for Pipe Flanges

BS ISO 13259:2010 非承压地下用热塑管路系统.弹性材料密封环式接缝的气密性试验方法

Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints

ISO 13259:2010 无压地下应用热塑性塑料管道系统.人造橡胶密封环型接头试验方法

Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints

SANS 7483:2010 符合ISO 7005标准的法兰密封垫圈的尺寸规格

Specifies the dimensions of gaskets for use in conjunction with flanges.

Dimensions of gaskets for use with flanges to ISO 7005

ANSI/ASTM F493:2010 氯化聚氯乙烯(CPVC)塑料管及配件用溶剂粘结剂规范

Specification For Solvent Cements For Chlorinated Poly Vinyl Chloride Cpvc Plastic Pipe And Fittings

ANSI/ASTM F477:2010 塑料管连接用弹性体密封件(垫圈)规范

Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

ASTM F477-10 连接塑料管用弹性体密封件(垫圈)的标准规范

1.1 This specification covers elastomeric seals (gaskets) used to seal the joints of plastic pipe used for gravity, low-pressure, and high-pressure applications. This refers to push-on joints which require no internal or external pressure to effect the initial seal. 1.2 Requirements are given for natural or synthetic rubber gaskets, or a combination of both. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

JC/T 41-2009 电绝缘石棉纸

本标准规定了电绝缘石棉纸的术语、分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于电绝缘石棉纸。

Asbestos paper for electric insulation

JC/T 69-2009 石棉纸板

本标准规定了石棉纸板的分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于作为500℃以下的隔热、保温和包覆式密封垫片内衬材料的石棉纸板。

Asbestos paper and millboard

JC/T 554-2009 石棉胶乳抄取板

本标准规定了石棉胶乳抄取板的术语、分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于各种内燃机气缸垫、进排气管垫及设备联接部或管法兰垫的抄取板。

Asbestos rubber latex beater jointing

SAE J1453/3-2009 O形环密封面连接器规范.第3部分:钢管接头,壁板,转环,钎套,连接器,帽盖和SAE J 1926-2英制螺杆端连接器的尺寸规格,试验和要求

1.1 PurposeThe three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers therequirements for “inch based” O-ring face seal connectors to inch stud ends along with the associated adapters, bulkheadand union connectors. Inch hex wrenching flats are predominantly used throughout this standard.1.2 Field of ApplicationThese connectors are intended for general application (see Figures 3, 4, and 5) and hydraulic systems on industrialequipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations inassembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systemsoperating from 95 kPa vacuum to working pressures shown in Table 4. Since many factors influence the pressure atwhich a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteedminimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user andmanufacturer to ensure that required performance levels are met.For use of these connectors in conditions outside the pressure and temperature limits specified, the manufacturers mustbe consulted.Both metric and inch tubing can be accommodated by changing only the sleeve to match the tube diameters. In the past,these connectors have been used predominantly with inch tubing. For new designs metric tubing should be considered.

Specification for O-Ring Face Seal Connectors: Part 3 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Connectors, Caps, and Connectors with SAE J 1926-2 Inch Stud Ends

ANSI/ASTM F2768:2009 塑料管道元件中带弹性密封的改良短牙英制梯形螺纹接合用规范

Specification For For Modified Stub Acme Thread Joint With Elastomeric Seal In Plastic Piping Components

ANSI/CSA LC7-2009 管接头密封化合物和材料

Pipe Joint Sealing Compounds and Materials

KS M ISO 9691:2008 橡胶.管接头的环工艺推荐标准.缺陷的说明和分类

이 표준은 파이프용 고무 접합부 링에서 결함을 서술하고 분류한다.

Rubber－Recommendations for the workmanship of pipe joint rings－Description and classification of imperfections

ASME B16.20-2007 管法兰用金属密封垫:绕制螺旋形有套环形接头

This standard covers materials, dimensions, tolerances, and markings for metal ring-joint gaskets, spiral-wound metal gaskets, and metal jacketed gaskets and filler material. These gaskets are dimensionally suitable for use with flanges described in the reference flange standards ASME B16.5, ASME B16.47, and API-6A. This standard covers spiral-wound metal gaskets and metal jacketed gaskets for use with raised face and flat face flanges.

Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and Jacketed

ASTM C1563-08(2017) 卫生排水, 废弃物, 通风和暴雨管设施用与衬套窝接式铸铁污水管和配件相连接用垫圈的标准试验方法

1.1 Several different types of compression gaskets are available for use in connection with hub and spigot cast iron soil pipe and fittings. The purpose of this test method is to establish material criteria and test procedures for compression gaskets used in joining hub and spigot cast iron soil pipe and fittings for sanitary drain, waste, vent, and storm drain piping applications in accordance with the general needs of producers, distributors, and users. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications

SAE J1453/3-2007 O型密封圈端面密封管接头用规范:第3部分:钢管接头、防水壁、旋转接头、铜焊管接头和封闭盖及SAE J 1926-2英制螺柱端连接管接头的要求、尺寸和试验

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers the requirements for "inch based" O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex wrenching flats are predominantly used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 3 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Connectors, Caps, and Connectors with SAE J 1926-2 Inch Stud Ends

SAE J1453-2-2007 O型密封圈端面密封管接头用规范:第2部分:钢管接头、防水壁、旋转接头、铜焊管接头、封闭盖和ISO 6149-2米制螺柱端连接管接头的要求、尺寸和试验

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-2 covers the requirements for "metric based" O-ring face seal connectors to metric stud ends along with the associated adapters, bulkhead and union connectors. Metric hex wrenching flats are used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 2 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with ISO 6149-2 Metric Stud Ends