23.040.80 管和软管组件的密封件 标准查询与下载

SAE J1453/3-2007 O型密封圈端面密封管接头用规范:第3部分:钢管接头、防水壁、旋转接头、铜焊管接头和封闭盖及SAE J 1926-2英制螺柱端连接管接头的要求、尺寸和试验

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 38 mm and for nominal hose diameters 6.3 mm through 38 mm. SAE J1453-3 covers the requirements for "inch based" O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex wrenching flats are predominantly used throughout this standard.

Specification for O-Ring Face Seal Connectors: Part 3 Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Connectors, Caps, and Connectors with SAE J 1926-2 Inch Stud Ends

CAN/ULC-S642-2007 螺纹管接头用化合物和胶带标准

This Standard sets forth minimum requirements for the determination of the acceptability of pipe joint compounds and tapes for piping systems intended for the containment of alcohol, alcohol fuel blends natural gas and methane, oxygen, petroleum distillates, propane and butane, steam, and water (potable and non-potable).Unless otherwise specified, products meeting this Standard are considered suitable for the sealing of all sizes of metal threaded connections.Products intended for use on limited sizes of connections may be considered in accordance with the intent of these requirements and suitably marked.This standard also provides for the determination of the flash point and ignition temperatures, and evidence of spontaneous heating, of pipe joint compounds.

Standard for Compounds and Tapes for Threaded Pipe Joints

DIN EN 681-1:2006 弹性密封件.给排水管道连接密封件材料要求.第1部分:硫化橡胶(包括修改件A1-1998 + A2-2002 + A3-2005和技术勘误AC-2002)

This Standard specifies requirements for materials used in vulcanized rubber seals for: 1) cold potable water supply (up to 50℃); 2) hot potable and non-potable water supply (up to 110℃); 3) drainage sewerage and rainwater systems (continuous flow up to 45℃ and intermittent flow up to 95℃. The different designations of seals specified are defined according to their type, application and requirements (see Table 4) General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevent product standards taking into account that the performance of pipe joints is a function of the seal material propertied, seal geometry and pipe joint design. This standard should be used where appropriate with product standards which specify performance requirements for joints. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastic. It is applicable to elastomeric components of composite or non composite seals. In case of composite seals for materials of hardness ranges from 76 IRHD to 95 IRHD the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function, or the long term stability of the seal. Joint seals made with an enclosed void as part of their design are included in the scope of this European Standard.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber(includes Amendments A1:1998 + A2:2002 + A3:2005 and Corrigendum AC:2002); English version of DIN EN 681-1:2006-11

DIN EN 681-2:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第2部分:热塑性弹体(包括修改件A1-2002 + A2-2005)

This standard specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of: 1) thermoplastic piping systems for non pressure waste water discharge (intermittent flow up to 95℃) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45℃ and intermittent flow up to 95℃); 3) thermoplastic rainwater piping systems. General requirements for finished joint seals are slso given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-2:2006-11

DIN EN 681-3:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第3部分:硫化多孔橡胶材料(包括修改件A1-2002 + A2-2005)

This standard specifies requirements for materials used in vulcanized rubber seals of celluar materials for non pressurized drainage, sewerage and rainwater systems and non-pressure non-potable water supply (continuous flow up to 45℃). General requirements for the finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product srandards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard is applicable to joint seals for pipeline materials of vitrified clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics. Joint seals made with an enclosed void as part of their design are included in the scope of this European Standard.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-3:2006-11

DIN EN 681-4:2006 弹性体密封件.给排水用管道连接密封件的材料要求.第4部分:聚氨酯铸塑密封件(包括修改件A1-2002 + A2-2005)

This Standard specifies requirements for materials used in factory cast polyurethane sealing elements used in joints for drainage, sewerage and rainwater systems and non potable water supply for continuous flow up to 45℃. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, plastics and glass-reinforced plastics.

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-4:2006-11

DIN EN 682:2006 弹性体密封件.输送气体和烃类液体的管道和配件用密封件的材料要求

This European Standard specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 °C up to 50 °C and in special cases from -15 °C up to 50 °C, for the following: General applications (see Table 4, type G) a) gaseous fuel (manufactured, natural and liquefied petroleum gas [LPG] in gaseous phase); b) hydrocarbon fluids with aromatic content up to 30 % (V/V), including LPG in liquid phase. Special applications (see Table 4, type H) Materials suitable for carrying gaseous fuels containing gas condensates and hydrocarbon fluids of unrestricted aromatic content. General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design. This European Standard should be used where appropriate with product standards which specify performance requirements for joints. This European Standard is applicable to joint seals for all pipeline materials including iron, steel, copper and plastics. In the case of composite seals requirements in 4.2.8 and 4.2.9 apply only when the materials used for any elastomeric parts come into contact with gaseous fuel or hydrocarbon fluid. Elongation at break, tensile strength, compression set and stress relaxation requirements for materials of hardness categories 80 and 90 apply only when they constitute that part of the seal which participates directly in the sealing function or in long term stability. This standard is not applicable to the following: a) seals made from cellular materials; b) seals with enclosed voids as part of their design; c) seals with requirements of resistance to flame or to thermal stress; d) seals which contain splices joining pre-vulcanized profile ends.

Elastomeric seals - Material requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids (includes Amendment A1:2005); English version of DIN EN 682:2006-10

JIS B 2404:2006 管法兰用垫片尺寸

この規格は，流体が蒸気，水，油などの配管に接合するフランジ()に便用するガスケットの種類及び寸法について規定する。

Dimensions of gaskets for use with pipe flanges

LST EN 14741-2006 热塑性塑料管道和导管系统 埋地非压力应用的接头 通过估计密封压力对具有弹性密封件的接头的长期密封性能的试验方法

Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure

BS EN 14741:2006 热塑性塑料管道和管道系统.非压力掩埋用接头.通过评估密封压力测定弹性密封件接合处的长期密封性能的试验方法

This draft European Standard specifies a method for determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.

Thermoplastics piping and ducting systems. Joints for buried non-pressure applications. Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure

DIN EN 14741:2006 热塑管和管道系统.地下非压力设施用接头.通过评估密封压力测定弹性密封件接头的长期密封性能的试验方法

This draft European standard specifies a method for determination of the long-term sealing pressure of elastomer seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.

Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure English version of DIN EN 14741:2006-05

NF T47-507:2006 橡胶O形环.橡胶O形环的包装、标识和储存

Rubber O-rings - Packaging, identification and storage of rubber O-rings.

EN 14741:2006 热塑管和管道系统.地下非压力设施用接头.通过评估密封压力测定弹性密封件接头的长期密封性能的试验方法

This draft European Standard specifies a method for determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.

Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure

LST EN 681-4+A1-2003/A2-2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 4：铸造聚氨酯密封元件

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - 4: Cast polyurethane sealing elements

LST EN 681-1+A1-2001/A3-2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第1部分：硫化橡胶

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber

LST EN 681-3+A1-2003/A2-2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第3部分：硫化橡胶的多孔材料

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber

LST EN 681-2+A1-2003/A2-2005 弹性密封件 用于给水和排水应用的管接头密封件的材料要求 第2部分：热塑性弹性体

Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers

LST EN 1514-2-2005 法兰及其接头 PN 标记法兰用垫片 第2部分：与钢制法兰一起使用的螺旋缠绕垫片

Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges

NF E29-533:2005 燃气装置.在供气态燃料管路或气瓶中使用的平垫圈选择的要求

Gas installations - Requirements for the choice of flat gaskets used in network supplied gaseous fuels or from cylinders.

NF E29-902-2:2005 法兰及其连接件.PN标示法兰用垫圈.第2部分:与钢法兰一起使用的螺旋形绕制垫圈

Flanges and their joints - Gaskets for PN-designated flanges - Part 2 : spiral wound gaskets for use with steel flanges.