23.060.01 阀门综合 标准查询与下载

GB/T 12251-2005 蒸汽疏水阀 试验方法

本标准规定了蒸汽疏水阀的试验方法和试验装置。 本标准适用于机械型、抗静力型和热动力型蒸汽疏水阀（以下简称疏水阀）的出厂检验和型式检验。

Automatic steam traps.Test methods

GB/T 12229-2005 通用阀门 碳素钢铸件技术条件

本标准规定了通用阀门、法兰、管件等承压碳素钢铸件（以下简称铸件）的技术要求、试验方法和检验规则等。 本标准适用于通用阀门、法兰、管件等承压铸件。

General Purpose industrial valves.Specification of carbon steel castings

GB/T 12227-2005 通用阀门 球墨铸铁件技术条件

本标准规定了通用阀门球墨铸铁件的技术要求、试验方法、检验规则及标志、包装与贮存等。 本标准适用于通用阀门、法兰、管件及其他受压的球墨铸铁件（以下简称铸件）。

General purpose industrial valves.Specification of spheroidal graphite iron castings

GB/T 12250-2005 蒸汽疏水阀 术语、标志、结构长度

本标准规定了机械型、抗静力型和热动力型蒸汽疏水阀的术语、结构长度和标志的一般要求。 本标准适用于工称压力在PN16～160，公称通径DN15～150的蒸汽疏水阀。

Automatic steam traps.Term、Marking、Face-to-face dimensions

GB/T 12226-2005 通用阀门 灰铸铁件技术条件

本标准规定了通用阀门灰铸铁件的技术要求、试验方法、检验规则及标志、包装与贮存等。 本标准适用于通用阀门、法兰、管件及其他受压的石磨为片状的灰铸铁件（以下简称铸件）。

General purpose industrial valves.Specification of flake graphite iron castings

GB/T 12222-2005 多回转阀门驱动装置的连接

本标准规定了多回转阀门驱动装置术语和定义，法兰代号和与其相对应的最大转矩及最大推力，与阀门连接的法兰尺寸，驱动件的结构形式和尺寸。 本标准适用于闸阀、截止阀、节流阀和隔膜阀用阀门驱动装置与阀门的连接尺寸，该尺寸也适合用于驱动装置与齿轮箱、齿轮箱与阀门的连接。

Multi-turn valve actuator attachments

GB/T 12243-2005 弹簧直接载荷式安全阀

本标准规定了弹簧直接载荷式安全阀的设计、材料和结构、性能、试验和检验、标志和铅封、供货等要求。 本标准适用于整定压力为0.1MPa～42.0MPa，流道直径大于或等于8mm的蒸汽锅炉、压力容器和管道用安全阀。

Spring loaded safety valves

GB/T 19672-2005 管线阀门 技术条件

本标准规定了法兰连接和焊接连接的闸阀、球阀、止回阀和旋塞阀的术语、结构型式和参数、订货要求、技术要求、材料、检验规则、试验方法、标志等。 本标准适用于公称压力PN1.6MPa～42.OMPa、公称通径DN15mm～1200mm的天然气和石油输送管线用的闸阀、球阀、止回阀和旋塞阀。

Specification of pipeline valves

GB/T 12223-2005 部分回转阀门驱动装置的连接

本标准规定了部分回转阀门驱动装置术语和定义、法兰代号和与其相对应的最大转矩值与阀门连接的法兰尺寸，驱动件的结构形式和尺寸。 本标准适用于球阀、蝶阀和旋塞阀用阀门驱动装置与阀门的连接尺寸，该尺寸也适合用于驱动装置与齿轮箱、齿轮箱与阀门的连接。

Part-turn valve actuator attachments

GB/T 17213.8-1998 工业过程控制阀 第8部分:噪声的考虑 第1节: 实验室内测量空气动力流流径控制阀产生的噪声

本标准规定了在实验室内测量可压缩流体流经控制阀和/或附属管道装置（包括固定节流装置）时，由这些设备辐射出在空中传播的声压级所使用的设备、测量方法和测量程序。 本标准不适用于直接向大气排放的控制阀。

Industrial-process control valves. Part 8: Noise considerations. Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

GB/T 17213.7-1998 工业过程控制阀 第7部分:控制阀数据单

本标准提出了一份各种要求的清单，这些要求都是采购绝大多数过程系统用控制阀所必需的。但本标准并不打算罗列出任何可以想象的过程系统的所有可能的要求。 清单的排列格式按标准化的数据表示方式设计，有助于填写者正确填写规格，并且为采用数据处理装置打下了基础。 为了保证能充分理解缩略语和填写数据的一致性，本标准附有详细的说明。

Industrial-process control valves. Part 7: Control valve data sheet

GB/T 17213.5-1998 工业过程控制阀 第5部分:标志

本标准规定了控制阀的强制性标志和补充标志。有些强制性标志可能不适用于一些结构极为特殊的控制阀，而有些补充标志则可能仅适用于特殊类型的控制阀。本标准建议，除了制造厂与买方另有商定外，各种阀的标志应符合本标准的规定。 强制性标志的标置方式应保证标志能永久保持。强制性标志应与阀体构成一体，或者标置在牢牢固定于阀体的金属牌（不同于标识铭牌）上。 本标准亦规定了补充标志的标置位置。补充标志通常标在标识铭牌上。 本标准代替GB/T17213.1《工业过程控制阀，第1部分：控制阀术语和总则》中的5.4。

Industrial-process control valves. Part 5: Marking

GB/T 17213.1-1998 工业过程控制阀 第1部分:控制阀术语和总则

GB/T 17213适用于各种类型的工业过程控制阀（以下简称控制阀）。该系列标准的第1部分给出了部分基本术语，同时就使用GB/T17213其他各部分的要求作了说明。

Industrial-process control valves. Part 1: Control valve terminology and general considerations

T/QGCML 4160-2024 油温控制阀通用技术规范

本文件规定了油温控制阀通用技术规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于油温控制阀的生产和检验。

General technical specifications for oil temperature control valves

T/QGCML 4159-2024 压力维持阀通用技术规范

本文件规定了压力维持阀通用技术规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于压力维持阀的生产和检验。

General technical specifications for pressure maintenance valves

GSO BS 1212-2:2024 浮子操作阀 第2部分：隔膜式浮子操作阀（铜合金阀体）规范（浮子除外）

  Scope is not provided for this standard

Float operated valves - Part 2: Specification for diaphragm type float operated valves (copper alloy body) (excluding floats)

GSO EN 12201-4:2024 供水、排水和压力污水处理用塑料管道系统 聚乙烯 (PE) 第4部分：阀门

This Part of EN 12201 specifies the characteristics of valves or valve bodies made from polyethylene (PE 100 and PE 80) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 For valves or valve bodies intended for drainage and sewerage under pressure, additional specifications/tests may be necessary according to the requirements of the purchaser, especially for the chemical resistance of the components in contact with the fluids and functioning characteristics. NOTE 2 For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.4. Components manufactured for water for other purposes may not be suitable for water supply for human consumption. It also specifies the test parameters for the test methods referred to in this European Standard. NOTE 3 Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to EN 12201 when they have relevant PE connection for butt fusion or electrofusion ends (see EN 12201-3:2011). In conjunction with Parts 1, 2, 3 and 5 of EN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar ) b) an operating temperature of 20 °C as a reference temperature; c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 4 For applications operating at constant temperature greater than 20 °C and up to 40 °C, see EN 12201 1:2011, Annex A. EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives. NOTE 5 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn ≤ 315 mm.

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves

GSO BS 1212-1:2024 浮子控制阀 第1部分：活塞式浮子控制阀（铜合金阀体）（不包括浮子）规范

  Scope is not provided for this standard

Float operated valves - Part 1: Specification for piston type float operated valves (copper alloy body) (excluding floats)

GSO BS 1212-3:2024 浮子操作阀 第3部分：仅用于冷水服务的隔膜式浮子操作阀（塑料阀体）（不包括浮子）的规范

  Scope is not provided for this standard

Float operated valves - Part 3: Specification for diaphragm type float operated valves (plastics bodied) for cold water services only (excluding floats)

GSO ISO 28921-1:2024 工业阀门 低温应用隔离阀 第1部分：设计、制造和生产测试

This document specifies requirements for design, dimensions, material, fabrication and production testing of gate, globe, ball/plug and butterfly valve design types used as isolation valves and check valves for low-temperature applications. This document is applicable to isolation valves for use in low and cryogenic temperature service where the design low-temperature service is -50 °C down to –196 °C. This document does not apply to valves for cryogenic services, designed in accordance with ISO 21011, used with cryogenic vessels. Where the requirements of this document vary from those given in the valve product standards, the requirements of this document apply. This document is applicable to valves with body, bonnet, bonnet extension or cover made of metallic materials. This document is applicable to: —    valves of nominal sizes DN: 10; 15; 20; 25; 32; 40; 50; 65; 80; 100; 125; 150; 200; 250; 300; 350; 400; 450; 500; 600; 650; 700; 750; 800; 850; 900; 950; 1 000; 1 050; 1 200; 1 350; 1 400; 1 500; 1 600; 1 650; 1 800, —    corresponding to nominal pipe sizes NPS: ⅜; ½; ¾; 1; 1 ¼; 1 ½; 2; 2 ½; 3; 4; 5; 6; 8; 10; 12; 14; 16; 18; 20; 24; 26; 28; 30; 32; 34; 36; 38; 40; 42; 48; 54; 56; 60; 64; 66; 72, and applies to pressure designations: —    PN 16; 25; 40; 100; 160; 250; 400, —    Class 150; 300; 600; 800; 900; 1 500; 2 500. NOTE       Not all type and size combination are available in all pressure ratings. This document does not apply to safety valves and control valves.

Industrial valves — Isolating valves for low-temperature applications — Part 1: Design, manufacturing and production testing