23.060.10 球阀 标准查询与下载

EN 161:2022 燃气器和燃气用具自动关闭阀

EN 13611:2019, Clause 1 applies with the following modification and addition: Modification: The 1st paragraph of EN 13611:2019, Clause 1 is replaced by: This document specifies the safety, design, construction, and performance requirements and testing for automatic shut-off valves for burners and appliances burning one or more gaseous fuels, hereafter referred to as “valves”. This document is applicable to valves with declared maximum inlet pressures up to and including 500 kPa and of nominal connection sizes up to and including DN 250. Addition: This document is applicable to: - electrically actuated valves; - valves actuated by fluids where the control valves for these fluids are actuated electrically, but not to any external electrical devices for switching the control signal or actuating energy; - valves where the flow rate is controlled by external electrical signals, either in discrete steps or proportional to the applied signal; - valves fitted with closed position indicator switches. An assessment method for valve designs is given by this document. The 4th paragraph of EN 13611:2019, Clause 1 is removed.

Automatic shut-off valves for gas burners and gas appliances

DIN 3588-3:2021 气体开孔三通 第3部分：合格评定

DIN 3588-3 defines requirements for the conformity assessment of gas tapping valves, with shut down device for polyethlene lines and of metal material with and without shut down device for grey iron and steel pipes. This standard is only valid in connection with DIN 3588-1 und DI

Gas Tapping Tees - Part 3: Conformity assessment

DIN 3588-2:2021 气体开孔三通 第2部分：铸铁和钢制管道的带和不带关闭功能 要求和测试

DIN 3588-2 applies to requirements and tests of gas tapping valves of metallic materialsmade of cast iron or steel with or without shut down device as well as possible auxiliary shutt-off device, which are fastened to the pipe to be tapped by means of a holding part, and for weld

Gas Tapping Tees - Part 2: With and without shut-off function for pipes made of cast iron and steel - Requirements and tests

DIN 3588-1:2021 气体开孔三通 第1部分：聚乙烯气体管道系统的开孔阀 要求和测试

This standard specifies product requirements and testing of tapping valves with or without shut down device and if necessary integral pilot shut down which are used in PE network systems, which are operated with gases according to DVGW G 260 (A) (without liquefied petroleum gas i

Gas Tapping Tees - Part 1: Tapping valves for polyethylene gas pipe systems - Requirements and tests

T/ZZB 2275-2021 耐腐蚀用镍基合金堆焊球阀

本文件规定了耐腐蚀用镍基合金堆焊球阀的结构型式、基本要求、技术要求、试验方法、检验规则、标志、防护、包装和贮运、质量承诺。 本文件适用于公称压力PN16～PN400、公称尺寸DN50～DN1400，压力等级Class150～Class2 500、公称尺寸NPS2～NPS56，适用温度-46 ℃～425 ℃，采用法兰连接，输送腐蚀性介质的镍基合金堆焊锻钢球阀。

Nickel base alloy surfacing ball valves for corrosion protection

T/ZZB 2203-2021 建筑用手动不锈钢螺纹球阀

本文件规定了建筑用手动不锈钢螺纹球阀的术语和定义、型式与参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于公称压力 PN≤4.0 MPa，公称尺寸 DN≤50 mm，工作温度-29 ℃≤t≤180 ℃的建筑物给排水用手动不锈钢螺纹球阀（以下简称球阀）。 本文件也适用于工作介质为非腐蚀性、非易燃易爆气体用手动不锈钢螺纹球阀。

Manually operated stainless steel threaded ball valves for buildings

GSO EN 13828:2021 建筑阀门 建筑物饮用水供应用手动铜合金和不锈钢球阀 测试和要求

This European standard applies primarily to copper alloy ball valves, dimensions DN 8 to DN 100, for potable water supply in buildings up to PN 10 and a distribution temperature of 65 °C. Occasional excursions up to 90 °C are permitted for a period of 1 h maximum. This standard applies also to ball valves in combination with other components in the same body. This standard specifies: - the requirements of the materials and the design of ball valves; - the mechanical, hydraulic and acoustic requirements of ball valves; - the test methods to verify the requirements of ball valves; - the marking requirements of ball valves. Ball valves in combination with other valves should fulfil the same requirements.

Building valves– Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings – Tests and requirements

DIN 86263:2021 船舶和海洋技术 船用直通阀 Y 型软密封，带承插连接，DN 15 至 DN 50，PN 16

The standard specifies valves with socket connection fou use in pipelines on board ships.

Ships and marine technology - Straight way valves for shipboard use - Y-patten, soft sealing, with socket connection, DN 15 to DN 50, PN 16

DIN 86265:2021 船舶和海洋技术 船用直通阀 Y 型软密封，普通型，带法兰，DN 15 至 DN 200

The document specifies valves with flanges for use in pipelines on board ships.

Ships and marine technology - Straight way valves for shipboard use - Y-patten, soft sealing, normal type, with flanges, DN 15 to DN 200

DIN 86264:2021 船舶和海洋技术 船用直通阀 Y 型软密封短型带法兰，DN 15 至 DN 200

The document specifies valves shot type with flanges for use in pipelines on board ships.

Ships and marine technology - Straight way valves for shipboard use - Y-patten, soft sealing, short type with flanges, DN 15 to DN 200

KS B ISO 12149-2020 一般用途的螺栓阀盖钢制截止阀

Bolted bonnet steel globe valves for general－purpose applications

T/ZZB 1837-2020 氟塑料衬里不锈钢球阀

本文件规定了氟塑料衬里不锈钢球阀的术语和定义、结构型式与基本参数、基本要求、技术要求、试验方法、检验规则、涂漆、标志、防护、包装、运输、贮存及质量承诺。 本文件适用于公称压力PN2.5～PN16，公称尺寸DN15～DN150，使用温度-20 ℃～120 ℃（FEP）、-20 ℃～180 ℃（PFA），输送介质为一般性腐蚀介质和各类强腐蚀介质（酸、碱、盐类，熔融碱金属、元素氟及芳香烃除外），端部连接形式为法兰连接的氟塑料衬里不锈钢球阀（以下简称球阀）。

Stainless steel ball valves for lining fluoroplastic

DIN 35860:2020 饮用水装置中的取样阀. 要求和试验

This test specification applies to sampling valves with nominal pressure PN 10 in the drinking water installation, which are used to collect drinking water samples in order to assess the condition of the drinking water according to the Drinking Water directive including the influ

Sampling valves in drinking water installations - Requirements and tests

T/ZZB 1680-2020 铜制快接阀门

本标准规定了铜制快接阀门（以下简称阀门）的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于工作介质为水或非腐蚀性液体或空气，公称尺寸 DN≤50 mm，工作温度-5 ℃≤t≤120 ℃，公称压力 PN≤2.5 MPa 的快接球阀、快接截止阀、快接闸阀、快接止回阀。

Copper quick connect valve

KS B 6030-2019 制冷剂截止阀

Stop valves for refrigerants

ASTM F1098-87(2019) 蝶阀和x2014的外壳尺寸标准规范；核动力源2至24

1.1 This specification provides standard dimensions for manual (lever and gear actuator) butterfly valves installed in shipboard piping systems in NPS 2 to NPS 24, inclusive. 1.2 This specification covers conventional and ASME B16.34 class butterfly valves of both lug and wafer types. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Envelope Dimensions for Butterfly Valves—NPS 2 to 24

BS EN ISO 21787:2006+A1:2019 工业阀门 热塑性材料截止阀

What is ISO 21787 — Globe valves of thermoplastic materials  about?    ISO 21787 specifies requirements for the design, functional characteristics and manufacturing  of globe valves made of thermoplastics materials intended for isolating and control service, their connection to the pipe system, the body materials and their pressure/temperature rating between − 40 °C and + 120 °C, for a lifetime of 25 years, and also specifies their tests.   ISO 21787 is applicable to hand- or power-operated valves to be installed in industrial pipe systems, irrespective of the field of application and the fluids to be conveyed.   NOTE 1 Industrial pipe systems also include systems for water supply for general purposes, drainage and sewerage.  NOTE 2 Special requirements can apply to pipe systems for water for human consumption.  NOTE 3 Different DN and/or PN can be declared by the manufacturer.  Who is ISO 21787 — Globe valves of thermoplastic materials for?   ...

Industrial valves. Globe valves of thermoplastics materials

EN ISO 21787:2006/A1:2019 工业阀.热塑性材料的球形阀 包含修改件A1,2019

Industrial valves - Globe valves of thermoplastics materials - Amendment 1 (ISO 21787:2006/Amd 1:2019)

ISO 21787:2006/Amd 1:2019 工业阀门.热塑性材料制截止阀.修改件1

Industrial valves — Globe valves of thermoplastics materials — Amendment 1

T/ZZB 0992-2019 燃气用埋地聚乙烯(PE)阀门

本部分规定了以聚乙烯材料为阀体的燃气用埋地聚乙烯阀门（以下简称“阀门”）的术语和定义、结构形式、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及产品随行文件、质量承诺以及售后服务。 本部分适用于PE 80或PE 100混配料制造的燃气用埋地聚乙烯阀门。 本部分规定的阀门与GB/T 15558.1—2015规定的管材及GB/T 15558.2—2005规定的管件配套使用，用于燃气输送。 本部分适用于具有插口端的双向阀门，阀门的插口端尺寸符合GB/T 15558.2—2005，阀门用于与符合GB/T 15558.1—2015的管材以及符合GB/T 15558.2—2005的管件连接。 本部分适用于公称直径小于或等于400 mm的阀门，工作温度范围在-20 ℃～40 ℃之间。 在输送人工煤气和液化石油气时，应考虑燃气中存在的其它组分（如芳香烃、冷凝液等）在一定浓度下对阀门性能产生的不利影响。

Buried polyethylene(PE) valve for the supply of gaseous fuels