23.100.01 流体动力系统综合 标准查询与下载

ISO 18582-1:2016 流体传动. 参考字典规格. 第1部分: 组织和结构的总体综述

Fluid power - Specification of reference dictionary - Part 1: General overview on organization and structure

JIS B 8390-1:2016 气压流体动力. 采用可压缩流体对部件流量特性的测定. 第1部分: 稳态流的通用规则和试验方法

Pneumatic fluid power -- Determination of flow-rate characteristics of components using compressible fluids -- Part 1: General rules and test methods for steady-state flow

GOST R 57174-2016 液压传动. 液压系统清洁度和组成液压系统的组件与液压流体清洁度的关联方法

Hydraulic fluid power. Method to relate the cleanliness of a hydraulic system to the cleanliness of the components and hydraulic fluid that make up the system

GSO ISO 14617-10:2015 原理图的原理图符号 第10部分：流体动力转换器

  Scope is not provided for this standard

Graphical symbols for diagrams -- Part 10: Fluid power converters

GSO ISO 5598:2015 流体动力系统及其组件 词汇

  Scope is not provided for this standard

Fluid power systems and components -- Vocabulary

BS ISO 19973-3:2015 气压传动.通过测试评定元件的可靠度.带活塞杆的气缸

Pneumatic fluid power. Assessment of component reliability by testing. Cylinders with piston rod

BS ISO 19973-2:2015 气压传动.通过测试评定元件的可靠度.方向控制阀

Pneumatic fluid power. Assessment of component reliability by testing. Directional control valves

BS ISO 19973-5:2015 气压流体动力. 通过试验评估部件的可靠性. 非回流阀, 梭阀, 双压阀 (AND功能), 单向可调流量控制阀和快速排气阀

Pneumatic fluid power. Assessment of component reliability by testing. Non-return valves, shuttle valves, dual pressure valves (AND function), one-way adjustable flow control valves, quick-exhaust valves

GSO ISO 15086-1:2015 液压流体动力 部件和系统的流体噪声特性的测定 第1部分：简介

This part of ISO 15086 provides a general introduction to transfer matrix theory, which allows the determination of the fluid-borne noise characteristics of components and systems. It also provides guidance on practical aspects of fluid-borne noise characterization. This part of ISO 15086 is applicable to all types of hydraulic fluid power circuits operating under steady-state conditions for fluid-borne noise over an appropriate range of frequencies.

Hydraulic fluid power -- Determination of the fluid-borne noise characteristics of components and systems -- Part 1: Introduction

GSO ISO 15086-3:2015 液压流体动力元件和系统的流体噪声特性的测定 第3部分：液压阻抗测量

This part of ISO 15086 describes the procedure for the determination of the impedance characteristics of hydraulic components, by means of measurements from pressure transducers mounted in a pipe. This part of ISO 15086 is applicable to passive components, irrespective of size, operating under steady-state conditions, over a frequency range from 10 Hz to 3 kHz.

Hydraulic fluid power -- Determination of the fluid-borne noise characteristics of components and systems -- Part 3: Measurement of hydraulic impedance

GSO ISO 9110-2:2015 液压流体动力 测量技术 第2部分：封闭管道中平均稳态压力的测量

This part of ISO 9110 establishes procedures for measuring the average steady-state pressure in a hydraulic fluid power conduit. It is applicable to the measurement of average steady-state pressure in closed conduits with inside diameters greater than 3 mm, transmitting hydraulic fluid power with average fluid velocities less than 25 m/s and average steady-state static pressures less than 70 MPa (700 bar). It is not applicable to sensors which are flush mounted with, or are an integral part of, the closed fluid conduit wall. It provides the formulae for estimating the total uncertainty in a given pressure measurement.

Hydraulic fluid power -- Measurement techniques -- Part 2: Measurement of average steady-state pressure in a closed conduit

GSO ISO 1219-1:2015 流体动力系统和组件 图形符号和电路图 第1部分：方便应用和数据处理的图形符号

This part of ISO 1219 establishes basic elements for symbols. It specifies rules for devising fluid power symbols for use on components and in circuit diagrams. This part of ISO 1219 is a collective application standard of the ISO 14617 series. In this part of ISO 1219, the symbols are designed in fixed dimensions to be used directly in data processing systems, which might result in different variants. NOTE In addition to terms in English and French, two of the three official ISO languages, this part of ISO 1219 gives the equivalent terms in German; these are published under the responsibility of the member body for Germany (DIN). However, only the terms and definitions given in the official languages can be considered as ISO terms and definitions.

Fluid power systems and components -- Graphical symbols and circuit diagrams -- Part 1: Graphical symbols for conventional use and data-processing applications

GSO ISO 2944:2015 流体动力系统和部件 标称压力

This International Standard specifies a series of nominal pressures from which to choose values used in other International Standards related to fluid power. It provides a standardized series from which to choose values applied to individual fluid power systems and/or components. The nominal pressures in this International Standard are for positive gauge pressures used with fluid power systems and/or components. NOTE See 3.1 and 4.3 for explanations of nominal pressure.

Fluid power systems and components -- Nominal pressures

GSO ISO 15086-2:2015 液压流体动力 部件和系统的流体噪声特性的测定 第2部分：管道中流体的声速测量

This part of ISO 15086 describes the procedure for the determination of the speed of sound in a fluid enclosed in a pipe, by measurements from pressure transducers mounted in the pipe. This part of ISO 15086 is applicable to all types of hydraulic circuit operating under steady state conditions, irrespective of size, for pressure pulsations over a frequency range from 25 Hz to 2500 Hz.

Hydraulic fluid power -- Determination of the fluid-borne noise characteristics of components and systems -- Part 2: Measurement of the speed of sound in a fluid in a pipe

GSO ISO/TR 19972-1:2015 液压油容量 液压元件可靠性评价依据 第1部分：通用程序和计算方法

Thispart of ISO/TR 19972 provides a means for determining the reliability of hydraulic fluid power components using: a) estimates from a design analysis; b) analysis of laboratory testing to failure or suspension; c) analysis of field data; d) analysis of a substantiation test. These methods apply to the first failures without repairs, but exclude certain infant mortality failures. Specific component test procedures and exclusions will be provided in subsequent parts of ISO/TR 19972. This part of ISO/TR 19972 also provides calculation methods, reporting descriptions and examples of reliability calculations.

Hydraulic fluid power -- Methods to assess the reliability of hydraulic components -- Part 1: General procedures and calculation method

GSO ISO 1219-2:2015 流体动力系统和组件 图形符号和电路图 第2部分：电路图

This part of ISO 1219 establishes the main rules for drawing hydraulic and pneumatic circuit diagrams using graphical symbols drawn in accordance with ISO 1219-1. This part of ISO 1219 also applies to circuit diagrams relating to cooling systems, lubrication systems, cooling lubricant systems and systems of technical gases used in conjunction with fluid power applications. It also includes examples of circuit diagrams. NOTE In addition to the text in English and French, two of the three official ISO languages, this part of ISO 1219 gives the equivalent text in German; this is published under the responsibility of the member body for Germany (DIN). However, only the text given in the official languages of ISO can be considered as ISO text.

Fluid power systems and components -- Graphical symbols and circuit diagrams -- Part 2: Circuit diagrams

GSO ISO 4413:2015 液压流体动力系统及其部件的一般规则和安全要求

This International Standard specifies general rules and safety requirements for hydraulic fluid power systems and components used on machinery as defined by ISO 12100:2010, 3.1. It deals with all significant hazards associated with hydraulic fluid power systems and specifies the principles to apply in order to avoid those hazards when the systems are put to their intended use. NOTE 1 See Clause 4 and Annex A. The significant hazard noise is incompletely deal with in this International Standard. NOTE 2 Noise emission depends especially on the installation of hydraulic components or systems into machinery. This International Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects: a) assembly; b) installation; c) adjustment; d) uninterrupted system operation; e) ease and economy of maintenance and cleaning; f) reliable operation in all intended uses; g) energy efficiency; and h) environment.

Hydraulic fluid power -- General rules and safety requirements for systems and their components

GSO ISO 4414:2015 气动流体容量系统及其部件的一般规则和安全要求

This International Standard specifies general rules and safety requirements for pneumatic fluid power systems and components used on machinery as defined by ISO 12100:2010, 3.1. It deals with all significant hazards associated with pneumatic fluid power systems and specifies principles to apply in order to avoid those hazards when the systems are put to their intended use. NOTE 1 See Clause 4 and Annex A. The significant hazard noise is incompletely dealt with in this International Standard. NOTE 2 Noise emission depends especially on the installation of pneumatic components or systems into machinery. This International Standard applies to the design, construction and modification of systems and their components, also taking into account the following aspects: a) assembly; b) installation; c) adjustment; d) uninterrupted system operation; e) ease and economy of maintenance and cleaning; f) reliable operation in all intended uses; g) energy efficiency; and h) environment. This International Standard does not apply to air compressors and the systems associated with air distribution as typically installed in a factory, including gas bottles and receivers.

Pneumatic fluid power -- General rules and safety requirements for systems and their components

GSO ISO 9110-1:2015 液压流体动力 测量技术 第1部分：测量的一般原理

This part of ISO 9110 establishes general principles for the measurement of performance parameters under static or steady-state conditions. It gives guidance on the sources and magnitudes of errors to be expected in the calibration of and measurements using hydraulic fluid power components. It describes practical requirements for assessing the capability of the measuring system, and hence the level of accuracy of measurement of the system, or for assisting in developing a system which will meet a prescribed level of accuracy.

Hydraulic fluid power -- Measurement techniques -- Part 1: General measurement principles

GSO ISO 8778:2015 气动流体动力 标准参考大气

This International Standard specifies a standard atmospheric reference value to be used in pneumatic fluid power technology for stating the performance data of components and systems.

Pneumatic fluid power -- Standard reference atmosphere