23.100.10 泵和马达 标准查询与下载
共找到 291 条与 泵和马达 相关的标准，共 20 页
本标准规定了塑料机械用液压齿轮泵的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于工作介质为液压油液或性能相当的其他液体，额定压力20 MPa～35 MPa的内啮合塑料机械用液压齿轮泵(以下简称齿轮泵)。
Hydraulic gear pump for plastic machinery
- ICS
- 23.100.10
- CCS
- C344
- 发布
- 2018-10-26
- 实施
- 2019-02-28
本标准规定了工程机械液压柱塞泵再制造的术语和定义、要求、标志、包装、运输和贮存。 本标准适用于合肥再制造集聚区内的工程机械液压柱塞泵再制造设计、生产，齿轮泵和叶片泵等其它泵类产品也可参照使用。
Construction Machinery Hydraulic System Remanufacturing Hydraulic Piston Pump
- ICS
- 23.100.10
- CCS
- C344
- 发布
- 2018-10-20
- 实施
- 2018-10-29
本标准规定了工程机械液压柱塞马达再制造的术语和定义、要求、标志、包装、运输和贮存。 本标准适用于合肥再制造集聚区内的工程机械液压柱塞马达再制造，齿轮马达和叶片马达等其它马达类产品也可参照使用。
Construction Machinery Hydraulic System Remanufacturing Hydraulic Piston Motor
- ICS
- 23.100.10
- CCS
- C344
- 发布
- 2018-10-20
- 实施
- 2018-10-29
本标准规定了端面配流型摆线液压马达（以下简称马达）的术语和定义、基本参数、基本要求、技术要求、检验方法、检验规则、标志、包装、运输、储存和质量承诺。 本标准适用于以液压油为工作介质，公称排量为80 mL/r～800 mL/r的端面配流型摆线液压马达。
Orbit hydraulic motor with disk valve
- ICS
- 23.100.10
- CCS
- C344
- 发布
- 2018-09-14
- 实施
- 2019-03-13
Test methods of remanufactured hydraulic motor for construction equipments
- ICS
- 23.100.10
- CCS
- 发布
- 2018-01-29
- 实施
Test methods of remanufactured hydraulic motor for construction equipments
- ICS
- 23.100.10
- CCS
- 发布
- 2018-01-29
- 实施
Test methods of remanufactured hydraulic pump for construction equipments
- ICS
- 23.100.10
- CCS
- 发布
- 2018-01-29
- 实施
Test methods of remanufactured hydraulic pump for construction equipments
- ICS
- 23.100.10
- CCS
- 发布
- 2018-01-29
- 实施
Hydraulic fluid power -- Determination of pressure ripple levels generated in systems and components -- Part 1: Method for determining source flow ripple and source impedance of pumps
- ICS
- 23.100.10
- CCS
- 发布
- 2017-10-20
- 实施
This International Standard describes and systematically defines the principal technical characteristics of hydraulic Pumps, motors and integral transmissions. lt allots letter Symbols to these characteristics, and indicates how they tan be more clearly defined by suffixes corresponding to particular cases. lt also lists an analysis of Parameter dimensions.
Hydraulic fluid power -- Pumps, motors and integral transmissions -- Parameter definitions and letter symbols
- ICS
- 23.100.10
- CCS
- 发布
- 2017-10-03
- 实施
在技术创新上，本标准规定了远程监控的指标及参数，比对远程监控的灵敏度进行了规定了，保证了远程监控及报警的准确性。
Solenoid valve for household and similar drinking water treatment equipment
- ICS
- 23.100.10
- CCS
- C349
- 发布
- 2017-05-30
- 实施
- 2017-09-04
Hydraulic fluid power. Determination of pressure ripple levels generated in systems and components. Method for determining source flow ripple and source impedance of pumps
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2016-03-31
- 实施
- 2016-03-31
本标准规定了液环泵溶媒回收机组（以下简称机组）的术语和定义、要求、试验方法、标志、使用说明书、包装、运输、贮存。 本标准适用于以液态溶媒为工作液，以气态溶媒或含气态溶媒的气体介质为抽送对象，在制药、化工等行业中以液环泵为核心机组的溶媒回收装置。
Technical conditions of liquid ring pump solvent recovery unit
- ICS
- 23.100.10
- CCS
- J78
- 发布
- 2016-03-07
- 实施
- 2016-06-07
Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Part 1: Method for determining source flow ripple and source impedance of pumps
- ICS
- 23.100.10
- CCS
- J20
- 发布
- 2015-10
- 实施
This part of ISO 16902 establishes a test code based on ISO 9614-1 and ISO 9614-2 for determining the sound power levels of a hydraulic fluid power pump under controlled conditions of installation and operation. The sound power level will include sound power radiated by any piping within the measurement surface. This part of ISO 16902 is suitable for providing a basis for comparing the airborne noise levels of any type of pump that is normally used to convert rotary mechanical power to hydraulic fluid power, incorporating valves, solenoids, drive gears, couplings or any other auxiliary device normally fitted in service.
Hydraulic fluid power -- Test code for the determination of sound power levels of pumps using sound intensity techniques: Engineering method -- Part 1: Pumps
- ICS
- 23.100.10
- CCS
- 发布
- 2015-09-03
- 实施
This part of ISO 3019 establishes a metric series of mounting flanges and shaft ends for positive-displacement, rotary hydraulic fluid power pumps and motors. It specifies sizes and dimensions and establishes an identification code for two- and four-bolt, and polygonal (including circular), mounting flanges, as well as for cylindrical keyed shaft ends, conical keyed shaft ends with an external thread and metric involute spline shaft ends. NOTE Involute spline is in accordance with DIN 5480.
Hydraulic fluid power -- Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors -- Part 2: Metric series
- ICS
- 23.100.10
- CCS
- 发布
- 2015-09-03
- 实施
