23.100.10 泵和马达 标准查询与下载

GSO ISO 3019-2:2015 液压流体动力 泵和排量马达安装法兰和轴端的尺寸和规则 第2部分：公制系列

This part of ISO 3019 establishes a metric series of mounting flanges and shaft ends for positive-displacement, rotary hydraulic fluid power pumps and motors. It specifies sizes and dimensions and establishes an identification code for two- and four-bolt, and polygonal (including circular), mounting flanges, as well as for cylindrical keyed shaft ends, conical keyed shaft ends with an external thread and metric involute spline shaft ends. NOTE Involute spline is in accordance with DIN 5480.

Hydraulic fluid power -- Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors -- Part 2: Metric series

GSO ISO 16902-1:2015 液压流体动力 泵声功率测定测试指南使用声强技术：工程方法 第1部分：泵

This part of ISO 16902 establishes a test code based on ISO 9614-1 and ISO 9614-2 for determining the sound power levels of a hydraulic fluid power pump under controlled conditions of installation and operation. The sound power level will include sound power radiated by any piping within the measurement surface. This part of ISO 16902 is suitable for providing a basis for comparing the airborne noise levels of any type of pump that is normally used to convert rotary mechanical power to hydraulic fluid power, incorporating valves, solenoids, drive gears, couplings or any other auxiliary device normally fitted in service.

Hydraulic fluid power -- Test code for the determination of sound power levels of pumps using sound intensity techniques: Engineering method -- Part 1: Pumps

GSO ISO 4409:2015 液压流体动力 正排量泵、马达和集成变速器 测试和展示稳定基本性能的方法

This International Standard specifies methods for determining the performance and efficiency of hydraulic fluid power positive displacement pumps, motors and integral transmissions. It applies to components having continuously rotating shafts. This International Standard specifies the requirements for test installations, test procedures under steady-state conditions and the presentation of test results.

Hydraulic fluid power -- Positive-displacement pumps, motors and integral transmissions -- Methods of testing and presenting basic steady state performance

GSO IEC 60609-1:2014 水轮机、蓄能泵和涡轮泵 空化过程产生的点蚀评估 第1部分：反动式涡轮机、蓄能泵和涡轮泵的评估

This part of IEC 60609 serves as a basis for the formulation of guarantees applied to cavitation pitting for reaction hydraulic turbines, storage pumps and pump-turbines. It addresses the measurement and evaluation of the amount of cavitation pitting on certain specified machine components for given conditions, which are defined in the contract by output, specific hydraulic energy (E), speed, material, operation, etc. The cavitation-pitting evaluation is based on the loss of material during a given time and under accurately defined operating conditions. All wetted surfaces are considered. The contract documents shall state whether cavitation pitting on the hydraulic machine should or should not be anticipated in all or in some operating ranges. Guarantees that restrict the extent of cavitation pitting are necessary in the contract whether cavitation pitting is anticipated or not.

Hydraulic turbines, storage pumps and pump-turbines - Cavitation pitting evaluation - Part 1: Evaluation in reaction turbines, storage pumps and pump-turbines

QB/T 4697-2014 家用和类似用途反渗透净水机、纳滤净水机专用加压泵

本标准规定了家用和类似用途反渗透净水机、纳滤净水机专用加压泵(以下简称为“泵”)的术语定义、产品分类和型号命名、要求、试验方法、检验规则和标志、包装、运输、贮存。本标准适用于家用和类似用途的反渗透净水机、纳滤净水机(DC24V)专用加压泵。

Household and similar booster pump for reverse osmosis water, nanofiltration water purifier

JB/T 11862-2014 起动用涡轮式气动马达

本标准规定了起动用涡轮式气动马达的型号与基本参数、技术要求、检验方法、检验规则、标志、包装、运输与贮存。本标准适用于柴汕机、天然气发动机及石汕、矿山机械等设备起动用的涡轮式气动马达(以下简称产品)。

Pneumatic turbine motors for starting

JB/T 11863-2014 齿轮式气动马达

本标准规定了齿轮式气动马达的型号与基本参数、技术要求、检验方法、检验规则和标志、包装、运输与贮存。本标准适用于齿轮式气动马达(以下简称产品)。

Pneumatic gear motors

GSO ISO 4392-2:2013 液压油的能力 决定发动机的特性 第2部分：启动运动的能力

This part of ISO 4392 specifies two test methods for determining the startability of rotary hydraulic motors. It describes two comparable methods of measurement, namely the constant torque method (see clause 6) and the constant pressure method (see clause 7). Since the results obtained by these two methods are equivalent, no preference is given to either. Additional physical quantities and their symbols are given in annex A. The accuracy of measurement is divided into three classes, A, B and C, which are explained in annex B.

Hydraulic fluid power -- Determination of characteristics of motors -- Part 2: Startability

GSO ISO 4392-1:2013 液压油的容量 确定发动机的特性 第1部分：恒定低速和恒定压力

This part of ISO 4392 describes a method of determining the low speed characteristics of positive displacement rotary fluid power motors, of either fixed or variable displacement types. The method involves testing at slow speeds which may generate frequencies having a significant influence upon the steady continuous torque output of the motor and affect the system to which the motor would be connected. The accuracy of measurement is divided into three classes, A, B and C, which are explained in annex A.

Hydraulic fluid power -- Determination of characteristics of motors -- Part 1: At constant low speed and constant pressure

GSO ISO 4392-3:2013 液压油的功率 确定发动机的特性 第3部分：恒定流量和恒定扭矩

This part of ISO 4392 describes a method of determining the low-speed characteristics of positive-displacement rotary fluid power motors under constant flow and constant torque conditions. Motors may be of either the fixed or variable-displacement type. The method involves testing at slow speeds, which may generate frequencies having a significant influence upon the steady continuous torque output of the motor and affect the system to which the motor would be connected. The accuracy of measurement is divided into three classes, А, В and C, which are explained in annex A.

Hydraulic fluid power -- Determination of characteristics of motors -- Part 3: At constant flow and at constant torque

KS B ISO 17559-2013 液压流体动力 电控液压泵 测定性能特性的试验方法

Hydraulic fluid power－Electrically controlled hydraulic pumps－Test methods to determine performance characteristics

KS B ISO 3019-1-2013 液压流体动力 容积泵和马达 安装法兰和轴端尺寸和识别代号 第1部分：公制单位英制系列

Hydraulic fluid power－Positive displacement pumps and motors－Dimensions and identification code for mounting flanges and shaft ends－Part 1：Inch series shown in metric units

KS B ISO 3019-2-2013 液压流体动力 容积泵和马达 安装法兰和轴端尺寸及识别代号 第2部分：二孔和四孔法兰和轴端 公制系列

Hydraulic fluid power－Positive displacement pumps and motors－Dimensions and identification code for mounting flanges and shaft ends－Part 2：Two－and four－hole flanges and shaft ends－Metric series

KS B ISO 3662-2013 液压流体动力 泵和马达 几何排量

Hydraulic fluid power－Pumps and motors－Geometric displacements

KS B ISO 10767-2-2013 液压流体动力 系统和部件中产生的压力脉动水平的测定 第2部分：泵的简化方法

Hydraulic fluid power－Determination of pressure ripple levels generated in systems and components－Part 2 : Simplified method for pumps

KS B ISO 4392-2-2013 液压流体动力 马达特性的测定 第2部分：启动性

Hydraulic fluid power－Determination of characteristics of motors－Part 2：Startability

KS B ISO 10767-3-2013 液压流体动力 系统和部件中产生的压力脉动水平的测定 第3部分：马达方法

Hydraulic fluid power－Determination of pressure ripple levels generated in systems and components－Part 3 : Method for motors

KS B ISO 4392-3-2013 液压流体动力 马达特性的测定 第3部分：恒流量和恒扭矩

Hydraulic fluid power－Determination of characteristics of motors－Part 3：At constant flow and at constant torque

KS B ISO 3019-3-2013 液压流体动力 容积泵和马达 安装法兰和轴端尺寸及识别代号 第3部分：多边形法兰（包括圆形法兰）

Hydraulic fluid power－Positive displacement pumps and motors－Dimensions and identification code for mounting flanges and shaft ends－Part 3：Polygonal flanges(including circular flanges)

KS B ISO 4392-3:2013 液压传动 第3部分：恒定流量和恒定扭矩的情况下测定液压马达特性

Hydraulic fluid power－Determination of characteristics of motors－Part 3：At constant flow and at constant torque