23.100.60 过滤器、密封垫和流体杂质 标准查询与下载

KS I ISO 18413-2015(2020) 液压传动零部件清洁度与污染物收集、分析和数据报告有关的检验文件和原则

Hydraulic fluid power－Cleanliness of parts and components－Inspection document and principles related to contaminant collection, analysis and data reporting

KS I ISO 10949-2015(2020) 液压传动－部件清洁度－实现和控制部件从制造到安装清洁度的指南

Hydraulic fluid power－Component cleanliness－Guidelines for achieving and controlling cleanliness of components from manufacture to installation

KS I ISO 16431-2015(2020) 液压传动装配系统清洁度检验

Hydraulic fluid power－Assembled systems－Verification of cleanliness

KS B ISO 11171:2015 液压传动 液体自动颗粒计数器的校准

Hydraulic fluid power－Calibration of automatic particle counters for liquids

KS I ISO 10949:2015 液压传动 元件清洁度 从生产到安装的过程中元件清洁度的取得和控制指南

Hydraulic fluid power-Component cleanliness-Guidelines for achieving and controlling cleanliness of components from manufacture to installation

JIS B 9932:2015 液压流体动力.流体自动颗粒计数器的校准

Hydraulic fluid power -- Calibration of automatic particle counters for liquids

GSO ISO 12500-4:2015 压缩空气过滤器 测试方法 第4部分：水

  Scope is not provided for this standard

Filters for compressed air -- Methods of test -- Part 4: Water

GSO ISO 16431:2015 液压流体动力 系统清洁程序和检查组合系统的清洁度

This International Standard defines methods a) to measure the cleanliness of a fluid in an assembled hydraulic fluid power system, b) to verify a required system cleanliness upon release of the system from the production area, and c) if needed, to clean the system to the required cleanliness level. The clean-up procedure specified in this International Standard is not intended to replace proper system flushing procedures; see ISO 23309 for a system flushing procedure. Components and parts used in such systems should be clean prior to assembly; see ISO 18413 for guidance.

Hydraulic fluid power -- System clean-up procedures and verification of cleanliness of assembled systems

GSO ISO 6194-1:2015 带法兰和弹性密封件的旋转轴密封件 第1部分：尺寸和公差

This part of ISO 6194 describes seals utilising elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see 6.1). This part of ISO 6194 shows seal types and examples. It also specifies the nominal dimensions and tolerances of the seals, shafts and housings, as well as a dimensional identification code. NOTE ISO 6194 is complementary to ISO 16589 which covers seals incorporating thermoplastic sealing elements.

Rotary shaft lip-type seals incorporating elastomeric sealing elements -- Part 1: Nominal dimensions and tolerances

GSO ISO 4021:2015 液压流体动力 颗粒污染分析 从操作系统管线中提取流体样本

This International Standard specifies procedures for extracting fluid samples from a hydraulic fluid power system under operation. The preferred method is to extract fluid samples from a main flowline of an operating hydraulic system in such a manner that the particulate contaminant in the sample is representative of the fluid flowing at the point of sampling. An alternative method is to extract a sample from the reservoir of an operating hydraulic system, but this method should only be used if a suitable sampler is not fitted. The samples taken are used for particulate contamination analysis.

Hydraulic fluid power -- Particulate contamination analysis -- Extraction of fluid samples from lines of an operating system

GSO ISO 6194-5:2015 带法兰和包含柔性密封元件的旋转轴密封件 第5部分：识别可见缺陷

This part of ISO 6194 describes seals utilizing elastomeric sealing elements. They are normally considered suitable for use only at low pressures (see ISO 6194-1:2007, 6.1). This part of ISO 6194 defines and classifies typical surface imperfections that can impair the function of the seals and is intended as a convenience for purchasers and manufacturers in their discussions concerning the importance of these imperfections in different applications. NOTE ISO 6194 (all parts) is complementary to ISO 16589 (all parts), which covers seals incorporating thermoplastic sealing elements.

Rotary-shaft lip-type seals incorporating elastomeric sealing elements -- Part 5: Identification of visual imperfections

GSO ISO 3968:2015 液压油容量 过滤器 压差与流量特性的评估

This International Standard specifies a procedure for evaluating differential pressure versus flow characteristics of hydraulic filters and constitutes a basis for agreement between the filter manufacturer and user. It also specifies a method for measurement of the differential pressure generated at different flow rates and viscosities by the relevant parts of a filter assembly, that is the housing, the filter element and any valves contained within the housing that are in the flow stream.

Hydraulic fluid power -- Filters -- Evaluation of differential pressure versus flow characteristics

GSO ISO 11500:2015 流体的液压能力 利用光学淬灭原理通过自动颗粒计数来确定液体样品的分子污染水平

This International Standard specifies an automatic particle counting procedure for determining the number and sizes of particles present in hydraulic-fluid bottle samples of clear, homogeneous, single-phase liquids using an automatic particle counter (APC) that works on the light-extinction principle. This International Standard is applicable to the monitoring of a) the cleanliness level of fluids circulating in hydraulic systems, b) the progress of a flushing operation, c) the cleanliness level of support equipment and test rigs, d) the cleanliness level of packaged stock. NOTE 1 Measurements can be made with particles suspended in the original liquid or in a sample of the liquid diluted with a compatible liquid to reduce coincidence error. NOTE 2 The presence of a fluid interface obstructs the light beam and gives false signals.

Hydraulic fluid power -- Determination of the particulate contamination level of a liquid sample by automatic particle counting using the light-extinction principle

GSO ISO 11170:2015 液压油容量 验证过滤器组件性能特征的测试顺序

This International Standard defines a sequence of tests for verifying filter elements. It can be used to check their hydraulic, mechanical and separation characteristics. This International Standard is not intended to qualify a filter for a particular duty or replicate conditions of service. This can only be done by a specific test protocol developed for the purpose, including actual conditions of use (e.g. the operating fluid). The procedure in this International Standard is applicable to individual fluids or types of fluids that have similar chemistry.

Hydraulic fluid power -- Sequence of tests for verifying performance characteristics of filter elements

GSO ISO 6194-4:2015 结合弹性体密封元件的旋转轴唇型密封件 第4部分：性能测试程序

ISO 6194 describes seals utilizing elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see ISO 6194-1:2007, 6.1). This part of ISO 6194 specifies general test requirements for rotary shaft lip-type seals. The tests may be used for qualification purposes. NOTE ISO 6194 is complementary to ISO 16589 which covers seals incorporating thermoplastic sealing elements.

Rotary shaft lip-type seals incorporating elastomeric sealing elements -- Part 4: Performance test procedures

GSO ISO 16589-1:2015 结合热塑性密封元件的旋转轴唇式密封件 第1部分：标称尺寸和公差

ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low pressure conditions. This part of ISO 16589 shows seal types and examples. It also specifies the nominal dimensions and tolerance of the seals, shafts and housings, as well as a dimensional identification code. NOTE ISO 16589 is complementary to ISO 6194, which covers seals incorporating elastomeric sealing elements.

Rotary shaft lip-type seals incorporating thermoplastic sealing elements -- Part 1: Nominal dimensions and tolerances

GSO ISO 16589-3:2015 包含热塑性密封件的法兰旋转轴密封件 第3部分：储存、搬运和安装

ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds, based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low pressure conditions. This part of ISO 16589 gives users of lip-type seals guidance on the careful storage and handling and proper installation of rotary shaft lip-type seals; attention is drawn to the hazards involved and ways of avoiding them are pointed out. NOTE ISO 16589 is complementary to ISO 6194, which covers seals incorporating elastomeric sealing elements.

Rotary shaft lip-type seals incorporating thermoplastic sealing elements -- Part 3: Storage, handling and installation

GSO ISO 21018-3:2015 流体液压动力 监测流体分子污染水平 第3部分：使用过滤器堵塞技术

This part of ISO 21018 specifies a method for the semi-quantitative determination of the particulate contamination level using the filter blockage technique (also known as the mesh-obscuration method or the pore-blockage technique) either on-line or off-line in containers. It also defines procedures for calibrating the instruments and verifying their correct operation both in the laboratory and in service. In general, the techniques described in this part of ISO 21018 are suitable for monitoring a) the general cleanliness level in hydraulic systems, b) the progress in flushing operations, c) support equipment and test rigs. The use of this method is applicable to all single- or multi-phase liquid systems.

Hydraulic fluid power -- Monitoring the level of particulate contamination of the fluid -- Part 3: Use of the filter blockage technique

GSO ISO 18413:2015 液压油容量零部件清洁度检验文件及污染物收集、分析和报告原则

This International Standard specifies the content of an inspection document that includes both the cleanliness requirement for the specified part or component and the inspection method to be used for evaluating its cleanliness level. The cleanliness requirement and inspection method shall be established and agreed upon by the parties involved. NOTE 1 Determination of what constitutes an appropriate cleanliness level requirement for any particular part or component is beyond the scope of this International Standard. NOTE 2 For the purposes of this International Standard, approved functional liquids are considered to be components. This International Standard is applicable to the wetted surfaces of any fluid power system part or component. Appearance defects and contamination by liquid or gaseous materials are not covered by this International Standard. This International Standard does not address safety problems that may arise from hazardous materials, operations and equipment associated with its use. The user of this International Standard is responsible for establishing appropriate safety and health practices and determining the applicability of regulatory limitations prior to use.

Hydraulic fluid power -- Cleanliness of components -- Inspection document and principles related to contaminant extraction and analysis, and data reporting

GSO ISO 2941:2015 液压流体动力 过滤元件 塌陷/爆破压力等级验证

This International Standard specifies a method for verifying the collapse/burst pressure rating of a hydraulic fluid power filter element, i.e. the capability of a filter element to withstand a designated differential pressure at the normal (i.e., intended direction of) flow, by means of pumping contaminated fluid through the filter element until either collapse/burst occurs or the maximum expected differential pressure is reached without element failure.

Hydraulic fluid power -- Filter elements -- Verification of collapse/burst pressure rating