23.100.60 过滤器、密封垫和流体杂质 标准查询与下载
共找到 549 条与 过滤器、密封垫和流体杂质 相关的标准，共 37 页
Hydraulic fluid power — Filters — Multi-pass method for evaluating filtration performance of a filter element
- ICS
- 23.100.60
- CCS
- 发布
- 2022-01-25
- 实施
- 0000-00-00
本文件规定了活性炭过滤的通风过滤系统的术语和定义、一般要求、系统构成、检验规则、标志、包装、运输及贮存。 本文件适用于处理海量空气质量数据。
Ventilation filter system with activated carbon filtration
- ICS
- 23.100.60
- CCS
- C348
- 发布
- 2021-12-04
- 实施
- 2021-12-04
1.1 This practice covers the processing of in-service fluids in preparation for particulate contamination analysis using membrane filters and is limited only by the liquid-to-membrane filter compatibility. 1.2 The practice covers the procedure for filtering a measured volume of liquid through a membrane filter. When this practice is used, the particulate matter will be randomly distributed on the filter surface for subsequent contamination analysis methods. 1.3 The practice describes procedures to allow handling particles in the size range between 2 µm and 1000 µm with minimum losses during handling. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Processing In-service Fluid Samples for Particulate Contamination Analysis Using Membrane Filters
- ICS
- 23.100.60
- CCS
- 发布
- 2021-10-01
- 实施
1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery health condition monitoring. 1.3 Debris removal techniques range from manual to automated. 1.4 Analysis techniques vary from visual, particle counting, microscopic, x-ray fluorescence (XRF), atomic emission spectroscopy (AES), and scanning electron microscopy energy dispersive x-rays (SEMEDX). 1.5 This guide is suitable for use with the following filter types: screw on, metal mesh, and removable diagnostic layer filters. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
- ICS
- 23.100.60
- CCS
- 发布
- 2021-10-01
- 实施
Test method of turbidity removal from microfilation flat sheet membrane
- ICS
- 23.100.60
- CCS
- 发布
- 20210928
- 实施
- 20210928
Test method of chemical resistance from ultrafiltration hollow fiber membrane
- ICS
- 23.100.60
- CCS
- 发布
- 20210928
- 实施
- 20210928
Test method of chemical resistance from microfiltration flat sheet membrane
- ICS
- 23.100.60
- CCS
- 发布
- 20210928
- 实施
- 20210928
Hydraulic spin-on filters with finite lives -- Method for verifying the rated fatigue life and the rated static burst pressure of the pressure-containing envelope
- ICS
- 23.100.60
- CCS
- 发布
- 2021-09-07
- 实施
- 2021-09-07
Hydraulic filter element test methods－Thermal conditioning and cold start-up simulation
- ICS
- 23.100.60
- CCS
- 发布
- 20210827
- 实施
- 20210827
Hydraulic fluid power－Filter elements－Method for end load test
- ICS
- 23.100.60
- CCS
- 发布
- 20210827
- 实施
- 20210827
ISO 12829:2016 specifies methods for verifying the rated fatigue life and the rated static burst pressure of the pressure-containing envelope (i.e. the filter housing) of a spin-on hydraulic filter with a disposable filter element and a finite life. Because the service life of housings for these types of filters is relatively short, a rated fatigue life of 100 000 cycles is judged sufficient for typical industrial applications.
Hydraulic spin-on filters with finite lives — Method for verifying the rated fatigue life and the rated static burst pressure of the pressure-containing envelope
- ICS
- 23.100.60
- CCS
- 发布
- 2021-07-01
- 实施
ISO 11171:2016 specifies procedures for the following: a) primary particle-sizing calibration, sensor resolution and counting performance of automatic particle counters (APCs) for liquids capable of analysing bottle samples; b) secondary particle-sizing calibration using suspensions verified with a primary calibrated APC; c) establishing acceptable operation and performance limits; d) verifying particle sensor performance using a truncated test dust; e) determining coincidence and flow rate limits.
Hydraulic fluid power — Calibration of automatic particle counters for liquids
- ICS
- 23.100.60
- CCS
- 发布
- 2021-07-01
- 实施
Hydraulic fluid power -- Monitoring the level of particulate contamination of the fluid - Part 3: Use of the filter blockage technique
- ICS
- 23.100.60
- CCS
- 发布
- 2021-06-01
- 实施
- 2021-06-01
Hydraulic fluid power - Multi-pass method of evaluating filtration performance of a filter element under cyclic flow conditions
- ICS
- 23.100.60
- CCS
- 发布
- 2021-06-00
- 实施
This document establishes methods for: — validating equipment used to prepare secondary calibration suspensions for automatic particle counters; — performing online secondary calibration of automatic particle counters; — matching two or more online particle counters, i.e. to count the same number of particles at a given size by two APCs associated online; — validating online particle counting systems with and without online dilution as used, for example, to measure the filtration efficiency of a hydraulic filter as described in the multi-pass filter test in
Hydraulic fluid power — Online automatic particle-counting systems for liquids — Methods of calibration and validation
- ICS
- 23.100.60
- CCS
- 发布
- 2021-05-10
- 实施
Hydraulic fluid power -- Fluids -- Method for coding the level of contamination by solid particles
- ICS
- 23.100.60
- CCS
- J20
- 发布
- 2021-03-22
- 实施
Hydraulic fluid power -- Fluid contamination -- Determination of particulate contamination by the counting method using an optical microscope
- ICS
- 23.100.60
- CCS
- 发布
- 2021-03-10
- 实施
- 2021-03-10
Hydraulic fluid power. Interpolation method for particle count and filter test data
- ICS
- 23.100.60
- CCS
- 发布
- 2021-02-19
- 实施
- 2021-02-19
Hydraulic fluid power. Background, impact and use of ISO 11171:2020 on particle count and filter test data
- ICS
- 23.100.60
- CCS
- 发布
- 2021-02-12
- 实施
- 2021-02-12
Hydraulic fluid power - Background, impact and use of ISO 11171:2020 on particle count and filter test data
- ICS
- 23.100.60
- CCS
- 发布
- 2021-02-00
- 实施
