23.120 通风机、风扇、空调器 标准查询与下载

T/ZZB 0745-2018 汽车底盘专用高强度法兰螺栓

本标准规定了汽车底盘专用高强度法兰螺栓的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、储运和质量承诺。 本标准适用于螺纹规格为M10～M14，性能等级为10.9 级，表面处理为锌铝涂层汽车底盘专用高强度法兰螺栓(以下简称：螺栓)。

High strength flange bolts for automotive chassis

18/30372461 DC BS EN 17291 风扇 确定和评估非住宅单向通风装置能效的程序和方法

BS EN 17291. Fans. Procedures and methods to determine and evaluate the energy efficiency of non-residential unidirectional ventilation units

CAN/CSA-C22.2 No.113-2018 风扇和通风机

1 Scope 1.1 This Standard applies to fans and ventilation equipment that are a) cord-connected, rated at not more than 250 V; b) permanently connected to supply circuits of 600 V or less, single-phase or three-phase; c) used in non-hazardous locations; d) used in household or commercial locations; e) used indoors or outdoors; and f) used in accordance with the Rules of the Canadian Electrical Code, Part I.

Fans and ventilators

T/ZZB 0535-2018 工业缝纫机用伺服电机及控制系统

本标准规定了工业缝纫机用伺服电机及控制系统的术语和定义、分类及基本参数、基本要求、技术要求、试验方法、标志、包装、运输、贮存和质量承诺。 本标准适用于工业缝纫机用伺服电机及控制系统（以下简称伺服电机及控制系统）。

Servo motor and control system for industrial sewing machine

T/ZZB 0512-2018 商用空调用轴流通风机

本标准规定了商用空调用轴流通风机(以下简称通风机)的术语和定义、型式与基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于叶轮外径(DR)不大于1000 mm、体积流量范围为1500 m3/h～50000 m3/h、静压范围为20 Pa～300 Pa的电动机直联及外转子电动机直联式单级轴流通风机。 本标准不适用于自由风扇。

Axial fan for commercial air conditioner

T/ZZB 0460-2018 静音节能型家用除湿机

本标准规定了静音节能型家用除湿机的术语及定义、型式和基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存及质量承诺。 本标准适用于以机械制冷方式除湿,冷凝热为再热方式且名义除湿量在0.16 kg/h～2.0 kg/h的整体式家用除湿机（以下简称家用除湿机）。

Low-noise and high-efficiency household dehumidifier

T/ZZB 0478-2018 风机用无刷直流电机

本标准规定了风机用无刷直流电机的基本型式与参数、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本标准适用于交直流电源供电,额定功率不大于60 W的一般用途风机用无刷直流电机（以下简称“电机”），不适用于外转子结构的电机。

Brushless DC motor for fan

T/CAS 231-2018 转速可控型房间空气调节器快速制冷（热） 技术要求

本标准规定了转速可控型房间空气调节器（以下简称“空调器“）快速制冷（热）性能的技术要求、试验方法、检验规则。 本标准适用转速可控型房间空气调节器产品。

Speed controllable room air conditioner rapid cooling (heating) technical requirements

KS C IEC 60335-2-80-2018(2023) 家用和类似用途电器.安全.第2-80部分:风扇的特殊要求

Household and similar electrical appliances — Safety — Part 2-80: Particular requirements for fans

KS C IEC 60335-2-80-2018 家用和类似电器安全 - 第2-80部分:风扇的特殊要求

Household and similar electrical appliances — Safety — Part 2-80: Particular requirements for fans

KS C IEC 60335-2-80:2018 家用和类似电器安全 - 第2-80部分:风扇的特殊要求

Household and similar electrical appliances — Safety — Part 2-80: Particular requirements for fans

KS C IEC 60335-2-40-2018 家用和类似电器 - 安全 - 第2-40部分:电热泵 空调和除湿机的特殊要求

Household and similar electrical appliances — Safety — Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

KS C IEC 60335-2-40:2018 家用和类似电器 - 安全 - 第2-40部分:电热泵 空调和除湿机的特殊要求

Household and similar electrical appliances — Safety — Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

ASTM E1258-88(2018) 风扇增压装置气流校准的标准试验方法

1.1 This test method covers the airflow measurement calibration techniques for fan pressurization systems used for measuring air leakage rates through building envelopes. 1.2 This test method is applicable to systems used for air leakage measurement as described in Test Method E779. 1.3 This test method involves the installation of the fan pressurization system in a calibration chamber. Use of the fan pressurization system in an actual building may introduce additional errors in the airflow measurement due to operator influence, interference of internal partitions and furnishings, weather effects, and other factors. 1.4 The proper use of this test method requires a knowledge of the principles of airflow and pressure measurement. 1.5 This standard includes two basic procedures, a preferred procedure, based on ASHRAE 51 ⁄AMCA 210, and an optional procedure based on a nonstandard airflow measurement technique, commonly used by manufacturers of fan pressurization devices, but which has not been compared with standard airflow measurement techniques. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Airflow Calibration of Fan Pressurization Devices

T/NFX 11-2018 吊扇

本标准主要参照国家标准GB/T 13380-2007《交流电风扇和调速器》制定，并根据企业实际生产情况，制定了悬挂系统的防跌落安全结构要求和相关的试验方法，还制定了防扇叶反装结构要求，填补了国家标准的空白。

ceiling fan

QB/T 5268-2018 强力地面吹风机

本标准规定了强力地面吹风机的产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于单相器具额定电压不超过250 V、其他器具额定电压不超过480 V的常规及具有热风功能的强力地面吹风机。 本标准不适用于其他特殊条件(例如有腐蚀性或爆炸性气体存在的地方)下使用的强力地面吹风机。

Powerful floor blower

QB/T 5262-2018 直流电风扇

本标准规定了直流电风扇的产品分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于直流额定电压不超过48 V，单相额定电压不超过250 V，由直流电动机驱动的台扇、壁扇、台地扇、落地扇、吊扇、顶扇、转页扇、柱式扇和装饰型吊扇及其调速器。 本标准不适用于其他特殊条件(例如有腐蚀性或爆炸性气体存在的地方)下使用的风扇。

D.C. electric fans

T/ZZB 0352-2018 家用落地式变频节能舒适空调器

本标准规定了家用落地式变频节能舒适空调器的术语和定义、产品分类、基本要求、技术要求、试验、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于采用风冷冷凝器、转速可控型全封闭型电动机－压缩机、以创造室内舒适环境为目的的额定制冷量在12kW以下家用落地式变频节能舒适空调器（以下简称空调器）。

Household floor type inverter energy saving comfort air conditioners

T/ZZB 0351-2018 变压器专用低噪声冷却通风机

本标准规定了变压器专用低噪声冷却通风机(以下简称通风机)的基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质保期限及质量承诺。 本标准适用于环境温度不低于-40℃、不高于80℃变压器冷却系统用的通风机。

Transformer dedicated low-noise cooling fan

DIN EN ISO 5801:2018 风扇.利用标准化通风道进行性能试验(ISO 5801-2017);德文版本EN ISO 5801-2017

This document deals with the determination of the performance of industrial fans of all types except those designed solely for air circulation e. g. ceiling fans and table fans. Estimates of uncertainty of measurement are provided and rules for the conversion, within specified limits, of test results for changes in speed, gas handled and, in the case of model tests, size are given.

Fans - Performance testing using standardized airways (ISO 5801:2017); German version EN ISO 5801:2017