23.140 压缩机和气动机械 标准查询与下载

GSO ISO 11011:2015 压缩空气 能源效率 评估

  Scope is not provided for this standard

Compressed air -- Energy efficiency -- Assessment

T/ZZB 027-2015 节能型喷油螺杆空气压缩机

本标准规定了节能型喷油螺杆空气压缩机（以下简称“螺杆空压机”）的术语和定义、基本要求、技术要求、试验方法、检验规则及标志、包装和贮存要求。 本标准适用于驱动电动机功率为2.2kW～630kW，额定排气压力为0.3MPa、0.5MPa、0.7MPa、0.8 MPa、1.0 MPa、1.25 MPa的一般用固定及移动螺杆空压机。 本标准不适用于一般用变频喷油螺杆空压机。

Oil injected screw air comprossor for energy conservation

JB/T 8867-2015 固定的往复活塞空气压缩机 储气罐

本标准规定了工作压力为0.7MPa、0.8MPa、1.0MPa、1.25MPa储气罐的型式、型号、设计参数和尺寸、要求、检验与验收、标志、包装和运输。本标准适用于GB/T 13279规定的空气压缩机使用的储气罐。本标准也适用于工作压力相当的其它容积式空气压缩机使用的储气罐。

Receiver of stationary reciprocating piston air compressors

JB/T 12564-2015 螺杆活塞串联压缩机组

本标准规定了螺杆活塞串联压缩机组（以下简称串联机组）的术语和定义、型号和基本参数、要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于电动机驱动的固定式和橇装式，压缩介质为空气，冷却方式为水冷，驱动电动机总功率不大于1 000 kW，额定排气压力不大于45 MPa的串联机组。 柴油机驱动的串联机组、拖移式串联机组和车装式串联机组可参照本标准执行。

Screw-piston tandem compressor unit

JB/T 12565-2015 中压单螺杆空气压缩机

本标准规定了中压单螺杆空气压缩机（以下简称空压机）的术语和定义、型号和基本参数、要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于驱动功率为15 kW～355 kW，额定排气压力为2.0 MPa～4.0 MPa的一般用固定式喷油单螺杆空气压缩机。移动式喷油单螺杆空气压缩机可参考本标准执行。

Single screw air compressor of medium pressure

JB/T 2589-2015 容积式压缩机 型号编制方法

本标准规定了容积式压缩机的型号编制方法。 本标准适用于容积式压缩机。

Displacement compressors.Methods for model designation

JB/T 2409-2015 螺杆压缩机转子和同步齿轮 基本参数及尺寸

本标准规定了螺杆压缩机转子(以下简称转子)和同步齿轮的基本参数和尺寸。 本标准适用于额定排气压力不高于5 MPa(PN50)，公称容积流量在0.1 m/min~1 500 m/min范围内的转子和同步齿轮。

The basic parameters and sizes of the rotor and timing gear of screw compressor

JB/T 7240-2015 一般用往复活塞空气压缩机 主要零部件 技术条件

本标准规定了一般用往复活塞空气压缩机(以下简称空压机)主要零部件的术语和定义、要求、试验方法和检验规则、标志、包装、运输和贮存。 本标准适用于驱动功率为0.18 kW~560 kW、额定排气压力不超过1.4 MPa的空压机的主要零部件。

Reciprocating air compressor for general use.Main components.Specifications

JB/T 9103-2015 往复活塞乙炔压缩机

本标准规定了往复活塞乙炔压缩机(以下简称压缩机)的型号和基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于额定排气压力2.5 MPa，公称容积流量不大于4.5 m/min的压缩机。 额定排气压力2.5 MPa以下的乙炔压缩机可参照执行。

Reciprocating acetylene compressor

JB/T 9107-2015 往复压缩机 术语

本标准规定了往复压缩机(以下简称压缩机)的基本概念，分类，参数，系统，附属设备和零、部件等的术语及其定义。 本标准适用于压缩机的教学、研究、设计、制造和经营领域。

Reciprocating compressors.Vocabulary

JB/T 12566-2015 核电用隔膜压缩机 技术条件

本标准规定了压水堆核电站用隔膜压缩机（以下简称隔膜压缩机）的型式与基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于额定排气压力不大于15 MPa、公称容积流量不大于55 m（标态）/h的隔膜压缩机，超出该范围的隔膜压缩机可参照执行。

Diaphragm compressor for nuclear power plant.Technical specifications

GSO ISO 7183:2015 压缩空气干燥机 规格和测试

This International Standard specifies the performance data that are necessary to state and applicable test methods for different types of compressed air dryers. It is applicable to compressed air dryers working with an effective (gauge) pressure of more than 50 kPa (0,5 bar), but less than or equal to 1 600 kPa (16 bar) and include the following: — adsorption dryers; — membrane dryers; — refrigeration dryers (including drying by cooling); — or a combination of these. NOTE A description of the principles of operation of the dryers within the Scope of this International Standard is given in Annex A. This International Standard identifies test methods for measuring dryer parameters that include the following: — pressure dew point; — flow rate; — pressure drop; — compressed-air loss; — power consumption; — noise emission. This International Standard also provides partial-load tests for determining the performance of energy saving devices or measures. The mounting, operating and loading conditions of dryers for the measurement of noise are given in Annex C. This International Standard is not applicable to the following types of dryers or drying processes: — absorption dryers; — drying by over-compression; — integral dryers.

Compressed-air dryers -- Specifications and testing

GSO ISO 5941:2015 压缩机、气动工具和设备 首选压力

This International Standard lays down a series of preferred pressures to be used as reference pressures when presenting performance data for compressors, pneumatic tools and pneumatic machines. Components for compressed air systems should also be designed to meet the standardized pressures. The stated pressures are effective (gauge) pressures, given in bars.

Compressors, pneumatic tools and machines -- Preferred pressures

GSO ISO 5389:2015 涡轮压缩机 性能测试手册

This International Standard applies to performance tests on turbocompressors of all types. It does not apply to fans and high-vacuum pumps, or to jet-type compressors with moving drive components Turbocompressors comprise machines in which inlet, compression and discharge are continuous flow processes. The gas is conveyed and compressed in impellers and decelerated with further increase in pressure in fixed vaned or vaneless stators. This International Standard is intended to provide standard provisions for the preparation, procedure, evaluation and assessment of performance tests on compressors as specified above. The acceptance test of the performance is based on this performance test code. Acceptance tests are intended to demonstrate fulfilment of the order conditions and guarantees specified in the contract.

Turbocompressors -- Performance test code

GSO ISO 5388:2015 固定式空气压缩机 安全规则和操作规范

1.1 This International Standard establishes standards for the safe design, construction, installation and operation of stationary and skid-mounted air compressors for general use. It specifies requirements to help minimize compressor accidents and defines general safety practices for the field. Potential hazards associated with compressors are listed and detailed under the following headings in clause 6 : a) improper lubrication; b) inadequate cooling; c) mechanical failures; d) personal injury; e) exposure to noise; f) fires and explosions in the pressure system; g) crankcase explosions; h) incorrect installation, operation or maintenance. This International Standard does not cover the prime movers, which are dealt with in other International Standards. 1.2 This International Standard is based on the requirement that the compressor components be designed in accordance with recognized good practice and applicable national standards. 1.3 This International Standard is intended to apply to stationary and skid-mounted air compressors for general use. However, the following types of compressor are specifically excluded : a) compressors with a shaft input less than 2 kW; b) compressors with an effective discharge pressure less than 0,5 bar (50 kPa); c) compressors with an effective discharge pressure exceeding 50 bar (5 MPa); d) compressors specifically supplying air for breathing, diving or surgery; e) compressors used for air brake systems f) ejectors.

Stationary air compressors -- Safety rules and code of practice

DIN EN ISO 11011:2015 压缩空气. 能源效率. 评定 (ISO 11011-2013); 德文版本EN ISO 11011-2015

Compressed air - Energy efficiency - Assessment (ISO 11011:2013); German version EN ISO 11011:2015

IEC 60335-2-34/AMD1/COR1:2015 家用和类似用途电器. 安全性. 第2-34部分: 电动机压缩机的特殊要求; 修改件1; 勘误表1

Household and similar electrical appliances - Safety - Part 2-34: Particular requirements for motor-compressors; Amendment 1; Corrigendum 1

EN ISO 11011:2015 压缩空气.能效评估(ISO 11011:2013)

Diese Internationale Norm legt Anforderungen an die Durchführung der Energiebewertung und Berichterstattung der Ergebnisse einer Energiebewertung von Druckluftsystemen (nachfolgend als "Energiebewertung" bezeichnet) fest, die das Gesamtsystem berücksichtigt, von Energiezufuhr bis zur als Ergebnis dieser Energiezufuhr verrichteten Arbeit. Diese Internationale Norm betrachtet Druckluftsysteme als drei funktionale Teilsysteme: Erzeugung, die die Umwandlung von primären Energieressourcen in Druckluftenergie umfasst; Übertragung, die die Bewegung von Druckluft vom Ort der Erzeugung zum Ort des Verbrauchs umfasst; Bedarf, der die Gesamtheit aller Druckluftverbraucher, einschließlich produktiver Endanwendungen und verschiedener Arten von Druckluftverlust umfasst. Diese Internationale Norm legt Anforderungen fest für: die Analyse der Daten aus der Energiebewertung; Berichterstattung und Dokumentation der Erkenntnisse aus der Energiebewertung; und Bestimmung der erwarteten Energieeinsparung, die sich aus dem Energiebewertungsprozess ergibt. Diese Internationale Norm bestimmt Rollen und Verantwortlichkeiten für die an der Energiebewertungstätigkeit Beteiligten. Diese Internationale Norm stellt beispielhafte Informationen in den Anhängen B, C, D, und E über die Art der zu erhebenden Daten bereit, die eine erfolgreiche Energiebewertung fördern. Die bereitgestellten Informationen sind nicht vollständig und bezwecken daher nicht, die Einbeziehung anderer Daten einzuschränken. Die Form und Präsentation der in den Anhängen angegebenen Informationen bezweckt ebenfalls nicht die Präsentationsweise der Berichterstattung an den Kunden einzuschränken.

Compressed air - Energy efficiency - Assessment

GSO ISO 10442:2014 石油、化工和天然气服务行业 集成波离心空气压缩机

This International Standard specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of constant-speed, packaged, integrally geared centrifugal air compressors, including their accessories, for use in the petroleum, chemical and gas service industries. It is also applicable to gas services other than air that are non-hazardous and non-toxic. It is not applicable to machines that develop a pressure rise of less than 35 kPa above atmospheric pressure, which are classed as fans or blowers. NOTE In this International Standard, where practical, US customary units have been included in brackets for information.

Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors

KS B ISO 5390:2014 压缩机.分类

Compressors — Classification