25.040.99 其他工业自动化系统 标准查询与下载

DIN EN 60873-2:2004 工业过程控制系统用电动和气动模拟图表记录仪.第2部分:检验指南和常规试验

Electrical and pneumatic analogue chart recorders for use in industrial process control systems - Part 2: Guidance for inspection and routine testing (IEC 60873-2:2004); German version EN 60873-2:2004

DIN EN 60873-1:2004 工业过程控制系统用电动和气动模拟图表记录仪.第1部分:性能评价方法

Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Part 1: Methods for performance evaluation (IEC 60873-1:2003); German version EN 60873-1:2004

BS EN 60873-1:2004 工业过程控制系统用电动和气动模似图表记录仪.性能评定方法

This part of IEC 60873 provides methods for determining the performance of all electrical and pneumatic analogue chart recorders operating from a standardized signal which may be used in process control. It is intended that continuous and dotted-line traces, multiple-pen and multiple-channel instruments should be covered. Some tests should not apply to all instruments and additional tests may be required for certain types of recorders. The object of this standard is to specify uniform methods of test for the evaluation of the performance of electrical and pneumatic analogue chart recorders operating from a standardized signal which may be used in process control. When a full evaluation in accordance with this standard is not required, those tests which are required should be performed and the results reported in accordance with those parts of the standard which are relevant. It should be made clear in such a report that the evaluation reported is not a full evaluation and the parts omitted should be indicated.

Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Methods for performance evaluation

IEC 60873-2:2004 工业过程控制系统用电动和气动模拟图表记录仪 第2部分:检查和常规试验指南

GB/T 3386的本部分适用于以过程控制用标准化信号工作的（工业过程控制系统用）电动和气动模拟图纸记录仪， 包括连续划线和打点的记录仪以及多笔和多点记录仪。有些试验可能不适用于所有记录仪， 而某些类型的记录仪则可能需要附加试验。 本部分旨在为电动和气动模拟图纸记录仪的检查和例行试验， 例如验收试验或修理后的试验提供技术指导。 全性能试验或者是在严酷条件(如高温）下使用的记录仪宜采用GB/T 3386.1。 只要有可能， 应按GB/T 18271 的规定进行试验， 试验人员必须备有并熟知改标准。 可接受性能的定量标准宜由制造厂与用户协商确定。 试验报告应指明做了那些试验。 本部分的要求应在征得制造厂和用户同意后生效。

Electrical and pneumatic analogue chart recorders for use in industrial process control systems - Part 2: Guidance for inspection and routine testing

IEC 60873-1:2003 工业过程控制系统用电动和气动模拟图表记录仪.第1部分:性能评定方法

GB/T 3386的本部分规定了确定所有以过程控制用标准化信号工作的电动和气动模拟图纸记录 仪，包括连续划线和打点的记录仪以及多笔和多点记录仪的性能的方法。有些试验可能不适用于所有 记录仪，而某些类型的记录仪则可能需要附加试验。 本部分旨在为以标准化信号工作的过程控制用电动和气动模拟图纸记录仪的性能评定规定统一的 试验方法。 当不需要按本部分作全面评定时，可只进行所需的试验。试验结果应按本部分有关条文的要求列 入试验报告。试验报告应阐明报告所述的评定不是全面评定，并指出省略的项目。

Electrical and pneumatic analogue chart recorders for use in industrial-process control systems - Part 1: Methods for performance evaluation

GOST R 34.1501.1-1992 信息技术.工业自动装置.工厂生产.第1部分:标准化参考模型和要求鉴定方法

Настоящий стандарт позволяет устанавливать и согласованно проводить работы по стандартизации в области промышленной автоматизации. Ста

Information technology. Industrial automatic. Shop floor production. Part 1. Reference model for standardization and a methodology for identification of requirements

BS DD 203-1:1991 工业自动化:车间生产.确定要求的标准化和方法学参照模型

This report presents and describes a means of identifying where new or revised manufacturing standards may be required. It establishes a Reference Model for Shop Floor Production, which is then used as the basis for developing a methodology for the identification and extraction of areas for standards. The assumptions used to develop the Reference Model are: * the field of intest is the manufacture of discrete parts and in particular the production (physical realisation) of these parts, * the Reference Model needs to be open-ended so that it can be revised to incorporate new technologies,and * the Reference Model needs to be generic in nature so that it can be applied to a wide range of applications and is not directed to a particular organisational structure of manufacturing. It is emphasised that the Reference Model: * provides a conceptual framework for understanding manufacturing and * can be used to identify areas of standards necessary to integrate manufacturing systems. The Reference Model does not however provide a methodology for designing, implementing, operating and maintaining any existing or future manufacturing automation system. There may be a need to develop other Reference Models which can be used for those purposes, perhaps based on the work described in this report. The development of such models is beyond the scope of this technical report.

Industrial automation: shop floor production - Reference model for standardization and a methodology for identification of requirements

ISO/TR 10314-1:1990 工业自动化 车间生产 第1部分:标准参考模型和要求识别的方法论

Presents and describes a means of identifying where new or revised manufacturing standards may be required. Establishes a reference model which is then used as the basis for developing a methodology for the identification and extraction of areas for standards. The field of interest is the manufacture of discrete parts and in particular the production of these parts. This model provides a conceptual framework for understanding manufacturing and can be used to identify areas of standards necessary to integrate manufacturing systems.

Industrial automation; shop floor production; part 1: reference model for standardization and a methodology for identification of requirements