25.080.01 机床综合 标准查询与下载

KS B ISO 447-2020 机床 - 控制器的操作方向

Machine tools — Direction of operation of controls

KS B ISO 16092-1:2020 机床安全.压力机.第1部分:一般安全要求

Machine tools safety — Presses — Part 1: General safety requirements

KS B ISO 16092-1-2020 机床安全.压力机.第1部分:一般安全要求

Machine tools safety — Presses — Part 1: General safety requirements

T/ZZB 1833-2020 轴承内外圈数控专用机床

本文件规定了轴承内外圈数控专用机床的术语和定义、结构、型号及基本参数、基本要求、技术要求、试验方法、检验规则、标志、包装、贮存、运输和质量承诺。 本文件适用于一次装夹完成轴承内圈或外圈粗、精多工序加工的数控专用机床（以下简称机床）。

CNC special machine for bearing inner and outer rings

ISO 230-3:2020 机床试验法规. 第3部分: 热效应测定

This document defines four tests: — an environmental temperature variation error (ETVE) test; — a test for thermal distortion caused by rotating spindles; — a test for thermal distortion caused by moving linear axes; — a test for thermal distortion caused by rotary motion of components. The tests for thermal distortion caused by moving linear axes (see Clause 7) are applicable to numerically controlled (NC) machines only and are designed to quantify the effects of thermal expansion and contraction as well as the angular deformation of structures. For practical reasons, the test methods described in Clause 7 apply to machines with linear axes up to 2000 mm in length. If they are used for machines with axes longer than 2000 mm, a representative length of 2000 mm in the normal range of each axis is chosen for the tests. The tests correspond to the drift test procedure as described in ISO/TR 16015:2003, A.4.2, applied for machine tools with special consideration of thermal distortion of moving linear components and thermal distortion of moving rotary components. On machine tools equipped with compensation for thermal effects these tests demonstrate any uncertainty in nominal thermal expansion due to uncertainty of coefficient of thermal expansion and any uncertainty of length due to temperature measurement.

Test code for machine tools - Part 3: Determination of thermal effects

20/30416025 DC BS EN ISO 16089 AMD1 机械工具 安全 固定式磨床

BS EN ISO 16089 AMD1. Machine tools. Safety. Stationary grinding machines

BS EN ISO 16092-4:2020 机床安全 压力机 气动压力机的安全要求

What is ISO 16092 ‑ 4 about?    ISO 16092 ‑ 4 , is part four of the multi-series standard that in addition to ISO 16092-1 , specifies the technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of pneumatic presses which are intended to work cold metal or material partly of cold metal.   ISO 16092 ‑ 4 deals with all significant hazards relevant for pneumatic presses, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). All the phases of the lifetime of the machinery as described in ISO 12100:2010, 5.4, have been taken into consideration.   Who is ISO 16092 ‑ 4 for?   ISO 16092

Machine tools safety. Presses - Safety requirements for pneumatic presses

EN ISO 16092-2:2020 机床安全压力机第2部分:机械压力机的安全要求

This document, in addition to ISO 16092-1, specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of the following groups of mechanical presses and mechanical press production systems: — Group 1: Presses with a part revolution clutch(es); — Group 2: Presses with a servo drive system (Mechanical servo presses). NOTE 1 Requirements in this document are essentially applicable to both groups of the mechanical press. If a requirement applies to only one group, then the group is specified. NOTE 2 Other types of motorized drive systems provide similar functionalities to what is commonly called "servo drives" or "servo motors", and as such their use is considered the same within the terms used in this document (e.g. variable frequency drive systems). The presses covered by this document range in size from small high-speed machines with a single operator producing small workpieces to large relatively slow-speed machines with several operators and large complex workpieces. This document deals with all significant hazards relevant to mechanical presses and ancillary devices (e.g. moving die cushions, work-piece ejectors, feeding and transfer systems) which are integral to the machine, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). All phases of the machine life cycle as described in ISO 12100:2010, 5.4 have been taken into consideration. NOTE 2 All significant hazards means those identified or associated with presses at the time of the publication of this document. In addition to machines not covered by ISO 16092-1:2017, this document does not cover machines which: a) transmit energy to impart press slide motion by using hydraulic or pneumatic means; b) have two or more slides moving in different angular orientations from each other; NOTE 3 This document applies to presses which have two or more slides moving in the same angular orientations, e.g. a press which has inner and outer slides. c) transmit energy to impart press slide motion by using a linear motor mechanism(s).

Machine tools safety - Presses - Part 2: Safety requirement for mechanical presses (ISO 16092-2:2019)

EN ISO 16092-4:2020 机床安全压力机第4部分:气动压力机的安全要求

This document, in addition to ISO 16092-1, specifies the technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of pneumatic presses which are intended to work cold metal or material partly of cold metal. This document deals with all significant hazards relevant for pneumatic presses, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). All the phases of the lifetime of the machinery as described in ISO 12100:2010, 5.4, have been taken into consideration.

Machine tools safety - Presses - Part 4: Safety requirements for pneumatic presses (ISO 16092-4:2019)

BS ISO 14955-3:2020 机械工具 机床环境评价金属切削机床能源效率测试原则

What is ISO 14955 ‑ 3 about?    ISO 14955 ‑ 3 is part three of the multi-series standard that supports the energy-saving design methodology according to ISO 14955 ‑ 1 and the methods for measuring energy supplied to machine tools and machine tool components defined in ISO 14955 ‑ 2 . ISO 14955 ‑ 3 addresses the environmental evaluation of machine tools during the use stage based on reference scenarios. It contains an example for metal cutting machine tools.   ISO 14955 ‑ 3 defines a methodological approach to assess relevant machine tool operating states based on an individual reference scenario for the energy assessment of machine tools and the integration of energy-efficiency aspects into machine tool design.   ISO 14955 ‑ 3

Machine tools. Environmental evaluation of machine tools - Principles for testing metal-cutting machine tools with respect to energy efficiency

ISO 14955-3:2020 机床机床环境评价第3部分:金属切削机床能效试验原理

This document supports the energy-saving design methodology according to ISO 14955-1 and the methods for measuring energy supplied to machine tools and machine tool components defined in stage based on reference scenarios. It contains an example for metal cutting machine tools. This document defines a methodological approach to assess relevant machine tool operating states based on an individual reference scenario for the energy assessment of machine tools and the integration of energy-efficiency aspects into machine tool design. This document explains what needs to be measured in line with ISO 14955-1 and ISO 14955-2. Furthermore, it shows how a reference scenario for the measurement of the machine function “processing”, according to ISO 14955-1, is evaluated. An example of how to use this document is given in Annex A. The results from applying this document are influenced by the effect of user behaviour and manufacturing strategies during the use phase. This document does not support the comparison of machine tools.

Machine tools — Environmental evaluation of machine tools — Part 3: Principles for testing metal-cutting machine tools with respect to energy efficiency

BS ISO 14955-5:2020 机械工具 机床环境评价 木工机床能源供应测试原则

What is ISO 14955 ‑ 5 about?    ISO 14955 ‑ 5 is part fifth of the multi-series standard that specifies technical requirements for testing procedures for evaluation of energy supplied during use phase for the design of machine tools to process wood and materials with similar physical characteristics to wood.   ISO 14955 ‑ 5 , along with ISO 14955-1 and ISO 14955-2, covers all significant energy requirements   relevant to woodworking machine tools, when they are used as intended and under the conditions foreseen by the manufacturer/supplier.   ISO 14955 ‑ 5 defines relevant operating states, optional shift regimes and optional machine toolactivities for several types of woodworking machine tools.   ISO 14955

Machine tools. Environmental evaluation of machine tools - Principles for testing woodworking machine tools with respect to energy supplied

ISO 14955-5:2020 机床机床环境评价第5部分:木工机床能量测试原理

This document specifies technical requirements for testing procedures for evaluation of energy supplied during use phase for the design of machine tools to process wood and materials with similar physical characteristics to wood. This document, along with ISO 14955-1 and ISO 14955-2, covers all significant energy requirements relevant to woodworking machine tools, when they are used as intended and under the conditions foreseen by the manufacturer/supplier. This document defines relevant operating states, optional shift regimes and optional machine tool activities for several types of woodworking machine tools. This document also applies to peripheral devices which are supplied as an integral part of the machine. This document also applies to machine tools which are part of an integrated manufacturing system where the energy required is comparable to those of machine tools working separately. This document applies to the following woodworking machine tools: — NC boring and routing machines; — horizontal beam panel sawing machines; — vertical panel sawing machines; — edge banding machines fed by chains; — wide belt calibrating and sanding machines; — four-sided moulding machines; — tenoning and/or profiling machines; — foiling/laminating machines; — dimension saws and circular saw benches; — single spindle vertical moulding machines (toupie); — surface planing, thickness planing, combined surface/thickness planing machines; — band sawing machines; — combined machines; — multi-blade rip-sawing machines; — presses and bending presses;  — mounting presses. A list of energy efficiency improvements for woodworking machine tools is given in Annex A.

Machine tools — Environmental evaluation of machine tools — Part 5: Principles for testing woodworking machine tools with respect to energy supplied

JB/T 10890.2-2020 高速精密滚珠丝杠副 第2部分：验收技术条件

High-speed precision ball screw pair Part 2: Acceptance technical conditions

JB/T 13812-2020 加工中心 性能试验方法

Machining center performance test method

JB/T 10890.1-2020 高速精密滚珠丝杠副 第1部分：性能试验规范

High-speed precision ball screw pair Part 1: Performance test specifications

KS B ISO 16090-1:2020 机床安全.加工中心 铣床 转移机.第1部分安全要求

Machine tools safety — Machining centres, Milling machines, Transfer machines — Part 1: Safety requirements

KS B ISO 16090-1-2020 机床安全.加工中心 铣床 转移机.第1部分安全要求

Machine tools safety — Machining centres, Milling machines, Transfer machines — Part 1: Safety requirements

ISO/TR 17243-3:2020 机床主轴.通过主轴箱上的测量评定机床主轴振动.第3部分:在600 r/min和12000 r/min之间运行的带滚动轴承的齿轮传动主轴

Machine tool spindles — Evaluation of machine tool spindle vibrations by measurements on spindle housing — Part 3: Gear-driven spindles with rolling bearings operating at speeds between 600 r/min and

KS B 4109-2019 机床安全通则

General code of safety for machine tools