共找到 219 条与 车刀 相关的标准,共 15 页
本标准规定了焊接聚晶金刚石或立方氮化硼直柄斜齿立铣刀和莫氏锥柄斜齿立铣刀的型式和尺寸、技术要求、性能试验、标志和包装等基本要求。 本标准适用于焊接聚晶金刚石或立方氮化棚立铣刀。
End mills with brazed polycristalline diamond or cubic boron nitride
JB/T 10231的本部分规定了高速钢车刀条的检测方法。本部分规定的方法并不是唯一的。 本部分适用于按GB/T 4211.1和GB/T 4211.2生产高速钢车刀条作质量判定检测。
Tool inspection methods Part 26: High speed steel tool bits
Carbide tips for brazing on turning tools.
이 규격은 강 및 주철 공작물의 선삭 가공에 사용하는 고속도강 바이트, 소결 탄화물 바
Tool-life testing with single-point turning tools
本部分规定了各种可转位车刀成品检测时的检测项目、检测方法和检测器具及检测基准。这些方法并非唯一的。 本部分适用于按GB/T 5343.1、GB/T 5343.2、GB/T 14297生产的可转位车刀的检测,其他可转位车刀可参照采用。
Tool inspection methods Part 18:Turning tools with indexable inserts
Single-point tool holders for turning and copying, for indexable inserts-Dimensions
Boring bars(tool holders with cylindrical shank) for indexable inserts-Designation
Boring bars for indexable inserts-Dimensions
この規格は,スローアウェイ(刃先交換)チップ(以下,チップという。)を保持する円形断面のシャンクをもつスローアウェイチップ用ホルダ(以下,ホルダという。)について規定する。
Boring bars for indexable inserts -- Dimensions
この規格は,スローアウェイ(刃先交換)チップ(以下,チップという。)を保持する,円形断面のシャンクをもつスローアウェイチップ用ホルダ(以下,ホルダという。)の呼び記号の付け方について規定する。
Boring bars (tool holders with cylindrical shank) for indexable inserts -- Designation
この規格は,主として金属の切削加工に用いる完成バイト(以下,バイトという。)について規定する。
Ground high speed steel tool bits
Turning tools with carbide tips. Internal tools.
Turning tools with carbide tips. External tools.
Boring bars for indexable inserts — Dimensions
Single-point tool holders for turning and copying, for indexable inserts — Dimensions
Turning tools with carbide tips - External tools
Turning tools with carbide tips. Internal tools
Turning tools with carbide tips - Marking requirements
Specifies recommended procedures for tool-life testing with high-speed steel, cemented carbide and ceramic single-point turning tools used for turning steel and cast iron workpieces. Establishes specifications for the following factors of tool-life testing: workpiece, tools, cutting fluid, cutting conditions, equipment, assessment of tool deterioration and tool life, test procedures and the recording, evaluation and presentation of results.
Tool-life testing with single-point turning tools
Настоящий стандарт распространяется на токарные расточные резцы с твердосплавными пластинами по ГОСТ 25395 и ГОСТ 25396. В настоящий стандарт
Turning tools with carbide tips. Types and dimensions
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号