25.100.10 车刀 标准查询与下载

ISO 5608:1980 可转位（一次性）刀片用车削和仿形刀架和刀筒.名称

Turning and copying tool holders and cartridges for indexable (throwaway) inserts — Designation

GOST 20872-1980 机械夹固的多面硬质合金刀片外缘用组装车刀.结构及尺寸

Contour turning tools with mechanically clamped cemented carbide indexible inserts. Design and dimensions

ANSI B212.13-1979 单刃旋转车刀夹型切削工具

This standard covers the dimensional envelope for various styles of singe-point roller-turner tools covering brazed, solid, or indexable insert types.

Roller Turner Type Cutting Tools, Single Point

CSN 22 3830-1978 碳化头单边粗磨钻探工具．基本尺寸

Schválení ST SEV 409-77 doporu?ilo federální ministerstvo v?eobecného strojírenství. Zpracovatel: Ná?adí, n. p., Praha - závod Dě?ín: ing. Miroslav Dolej? Pracovník ??adu pro normalizaci a mě?ení: ing. Krista Komrsková

Carbide-tipped side roughing boring tools. Basic dimensions

CSN 22 3816-1978 60°挺进角碳化头直立旋转台刀具

Schválení ST SEV 415-77 doporu?ilo federální ministerstvo v?eobecného strojírenství. Zpracovatel: Ná?adí, n. p., Praha - závod Dě?ín: ing. Miroslav Dolej? Pracovník ??adu pro normalizaci a mě?ení: ing. Krista Komrsková

Carbide-tipped straight roughing turret tools with approach angle 60 degrees. Basic dimensions

CSN 22 3818-1978 碳化头单边粗磨旋转台刀具基本尺寸

Schválení ST SEV 417-77 doporu?ilo federální ministerstvo v?eobecného strojírenství. Zpracovatel: Ná?adí, n. p., Praha - závod Dě?ín: ing. Miroslav Dolej? Pracovník ??adu pro normalizaci a mě?ení: ing. Krista Komrsková

Carbide-tipped side roughing turret tools. Basic dimensions

CSN 22 3820-1978 碳化头瓶颈加工旋转刀具．基本尺寸

Schválení ST SEV 418-77 doporu?ilo federální ministerstvo v?eobecného strojírenství. Zpracovatel: Ná?adí, n. p., Praha - závod Dě?ín: ing. Miroslav Dolej? Pracovník ??adu pro normalizaci a mě?ení: ing. Krista Komrsková

Metal cutting tools. Carbide-tipped turret finishing tools. Basic dimensions

CSN 22 3824-1978 盲孔碳化头内部旋转台刀具．基本尺寸

Schválení ST SE V 420-77 doporu?ilo federální ministertsvo v?e obecného strojírenství. Zpracovatel: Ná?adí, n. p., Praha - závod Dě?ín: ing. Miroslav Dolej? Pracovník ??adu pro normalizaci a mě?ení: ing. Krista Komrsková

Metal cutting tools. Carbide-tipped turret inside cutting tools for blind holes. Basic dimensions

CNS 4267-1978 焊接碳化物车刀

焊接碳化钨车刀，一般分为硬焊型（brazed）及锁固型（throw–away type），此规格仅就硬焊型碳化物车刀（以下简称车刀）所做之规定。

Single Point Carbide Tipped Tools

ISO 5421:1977 精磨的高速钢刀刃

This International Standard lays down the dimensions of ground high speed steel tool bits of : — round section (clause 2) — square section (clause 3) — rectangular section (clause 4) — trapezoidal section (clause 5)

Ground high speed steel tool bits

ISO 242:1975 硬质合金焊接车刀片

This International Standard lays down the dimensions of carbide tips for turning tools intended to be fixed on the shanks of tools by brazing. NOTE — Throwaway carbide indexable inserts are the subject of ISO 883.

Carbide tips for brazing on turning tools

ISO 514:1975 硬质合金车刀 内圆车刀

This International Standard specifies the types and dimensions of turning tools with carbide tips; it deals only with internal tools. External tools and the definition of right-hand and left-hand tools are the subject of ISO 243; designation and marking are the subject of ISO 504. The shank sections and the inserts used are selected respectively from those defined in ISO 241 and ISO 242.

Turning tools with carbide tips; Internal tools

ISO 504:1975 硬质合金车刀 名称和标志

This International Standard specifies the designation and marking of turning tools with carbide tips, metric series, covered by ISO 243 and ISO 514, which relate to external tools and internal tools respectively. The designating numbers for "type of tool" are those which appear in these International Standards. The designating symbols for "groups of application" are those of ISO 513.

Turning tools with carbide tips; Designation and marking

ISO 243:1975 硬质合金车刀 外圆车刀

This International Standard specifies the types and the dimensions of turning tools with carbide tips; it deals only with external tools. It also gives the definition of right-hand and left-hand tools. Internal tools are the subject of ISO 514; designation and marking are the subject of ISO 504. The shank sections and the inserts used are selected respectively from those defined in ISO 241 and ISO 242.

Turning tools with carbide tips; External tools

GOST 20874-1975 机械夹固的多面硬质合金刀片组装刨刀.结构及尺寸

Combined turning and boring tools with mechanically clamped cemented carbide indexible inserts. Design and dimensions

GOST 18869-1973 高速钢直通外圆车刀.结构及尺寸

HSS straight bullnose turning tools. Design and dimensions

GOST 18868-1973 镶高速钢刀片的弯头外圆车刀.结构及尺寸

HSS tipped bent bullnose turning tools. Design and dimensions

GOST 10044-1973 高速钢刀杆镗刀.结构及尺寸

Настоящий стандарт распространяется на расточные державочные резцы общего назначения из быстрорежущей стали

High-speed steel boring tools with holders. Design and dimensions

GOST 18884-1973 镶硬质刀片切断切刀.结构及尺寸

Настоящий стандарт распространяется на токарные отрезные резцы общего назначения с напаянными пластинами из твердого сплава.

Carbide-tipped cutting-off turning tools. Design and dimensions

GOST 18883-1973 加工不通孔用镶硬质合金刀片镗刀.结构及尺寸

Настоящий стандарт распространяется на токарные расточные резцы общего назначения с напаянными пластинами из твердого сплава для обрабо

Carbide-tipped boring turning tools for blind holes. Design and dimensions