共找到 111 条与 刨床、拉床用刀具 相关的标准,共 8 页
이 규격은 탄소 공구강 바이트, 합금 공구강 바이트 및 고속도강 바이트를 사용하여 길이 방
Method of life test for single point tools
Method of life test for single point tools
本部分规定了各矩形花键拉刀检测时的检测方法和检测器具,这些方法并非唯一的。 本部分适用于按JB/T 5613、JB/T 9992生产的矩形花键拉刀的检测。
Tool inspection methods Part 20:Straight spline broaches
本部分规定了各种键槽拉刀检测时的检测方法和检测器具,这些方法并非唯一的。 本部分适用于按GB/T 14329.1~4生产的键槽拉刀的检测。
Tool inspection methods Part 19:Keyway broaches
本部分规定了圆拉刀检测时的检测方法和检测器具,这些方法并非唯一的。 本部分适用于按JB/T 7962生产的加工直径在120mm以内的光滑圆柱孔的圆拉刀的检测。
Tool inspection methods Part 7:Round broaches
この規格は,JIS B 1301に規定するキーの呼び寸法3x3~16x10に対応するキー溝の加工に用いる平形のキー溝プローチ(以下,プローチという。)について規定する。
Keyway broaches
この規格は,JIS B 1603に規定するインボリュートスプライン穴(以下,スプライン穴という。)で,モジュール(m)0.5~5 mmに対応するスプライン穴を加工するインボリュートスプラインブローチ(以下,ブローチという。)について規定する。
Involute spline broaches
Настоящий стандарт распространяется на комбинированные двухпроходные протяжки универсального назначения с навертным хвостовиком диаме
Combined broaches with diameter from 55 to 130 mm for slitting holes with involute profile with wind round tail and centring at outside dimeter with modul from 3 to 5. Construction
Настоящий стандарт распространяется на комбинированные двухпроходные протяжки универсального назначения с навертным хвостовиком диаме
Combined broaches with diameter from 90 to 120 mm for slitting holes with involute profile with wind round tail and centring at outside diameter with module from 2,5 mm. Construction
Настоящий стандарт распространяется на комбинированные однопроходные протяжки универсального назначения с навертным хвостовиком диаме
Combined broaches with diameter from 55 to 130 mm for slitting holes with involute profile with wind round tail and centring at outside diameter with module from 3 to 4 mm. Construction
Настоящий стандарт распространяется на комбинированные однопроходные протяжки универсального назначения с навертным хвостовиком диаме
Combined broaches with diameter from 50 to 120 mm for slitting holes with involute profile with wind round tail and centring at outside diameter with module from 1,5 to 2,5 mm. Construction
Broaches for cylindrical, slitting and polyhedral profile holes. Specifications
Настоящий стандарт распространяется на протяжки универсального назначения для обработки шпоночных пазов шириной от 6 до 50 мм по ГОСТ 23360,
Key broaches. Design
Настоящий стандарт распространяется на протяжки универсального назначения для обработки шпоночных пазов шириной от 10 до 50 мм по ГОСТ 23360,
Key broaches for higher class roughness. Design
Настоящий стандарт распространяется на протяжки универсального назначения для обработки шпоночных пазов шириной от 3 до 10 мм по ГОСТ 23360,
Flat teeth key broaches. Design
Настоящий стандарт распространяется на протяжки универсального назначения для обработки за один проход шпоночных пазов шириной от 3 до 10
Thick cored key broaches. Design
Internal broaches for straight splines based at internal diameter three pass combined type. Construction
Broaches with diameter from 50 to 120 mm for slitting holes with involute profile with round tail and centring at outside diameter with modul frome 1,5 to 2,5 mm. Construction
Broaches with diameter from 90 to 120 mm for slitting holes with involute profile with round tail and centring at outside diameter with modul from 2,5 mm. Construction
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号