25.100.60 锉刀 标准查询与下载



共找到 190 条与 锉刀 相关的标准,共 13

本标准规定木工、铁工、铜工及磨锯用锉之检验法。

Method of Test for Files

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Half-round File for Carpenter, Wide Flat End

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Flat File for Smith, Sharp Flat End

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Flat File for Smith, Wide Flat End

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Half-round File for Tinman

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Flat File for Tinman

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Heavy Round File for Smith

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Heavy Triangular File for Smith

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Round File for Smith

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Half-round File for Smith

ICS
25.100.60
CCS
发布
1978-03-02
实施
1978-03-02

Настоящий стандарт распространяется на надфили, предназначенные для обработки металлов, изготовляемые для нужд народного хозяйства и эк

Needle files. Technical conditions

ICS
25.100.60
CCS
发布
1977
实施
1979-01-01

This specification covers the material, dimensional, and finish requirements for the following four categories of tools: a) Machinists' files b) Saw files c) Miscellaneous files d) Rasps NOTE a) Requirements that must be specified by the purchaser are listed in Appendix A.

Files and rasps

ICS
25.100.60
CCS
发布
1977
实施

This part of ISO 236 specifies the dimensions of the long fluted machine reamers. It comprises three tables giving respectively the preferred sizes with corresponding dimensions in millimetres, and in inches, the corresponding sizes, in millimetres and in inches, set out as functions of diameter steps. Provision is also made for tolernces on lengths and cutting diameters.

Long fluted machine reamers, Morse taper shanks

ICS
25.100.60
CCS
J41
发布
1976-11
实施

Zpracovatel: Tona, n. p., Jihlava - Alois Starka Pracovník ??adu pro normalizaci a mě?ení - Jana Kal?íková

Hand files. Basic regulations

ICS
25.100.60
CCS
发布
1976-04-02
实施

Machine chucking reamers with morse taper shanks (and expansion chucking reamers).

ICS
25.100.60
CCS
J41
发布
1976-03-01
实施
1976-02-18

Machine chucking reamers with parallel shanks.

ICS
25.100.60
CCS
J41
发布
1976-03-01
实施
1976-02-18

Lays down only metric dimensions. For each type of reamer mentioned above ISO 521 gives two tables, one showing preferred sizes with corresponding dimensions and the other, a general table set out as functions of diameter steps. Provision is also made for tolerances on length, cutting diameters and the diameters of parallel shank.

Machine chucking reamers with parallel shanks or Morse taper shanks

ICS
25.100.60
CCS
J41
发布
1975-09
实施

Lays down only metric dimensions, which are the only recommended dimensions in the future for these types of reamers. The reamers have been designed to produce holes for taper pins manufactured to ISO 2339 in the range 5 to 50 mm nominal diameter. Unless otherwise stated, these tools will be rigth-hand cutting. The flutes may be straigth or spiral at the option of the manufacturer.

Machine taper pin reamers with Morse taper shanks

ICS
25.100.60
CCS
J41
发布
1975-08
实施

Lays down only metric dimensions, which are the only recommended dimensions in the future for these types of reamers. The reamers have been designed to produce holes for taper pins manufactured to ISO 2339 in the range 2 to 12 mm nominal diameter. Unless otherwise stated, these tools will be rigth-hand cutting. The flutes may be straigth or spiral at the option of the manufacturer.

Machine taper pin reamers with parallel shanks

ICS
25.100.60
CCS
J41
发布
1975-08
实施

Machine reamers for morse tapers Aléoirs à machine pour c?nes morseZusammenhang mit der von der International Organization for Standardization (ISO) herausgegebenen Internationalen Norm ISO 2250 —1972 siehe Erl?uterungen.

Machine Reamers for Morse Tapers

ICS
25.100.60
CCS
J41
发布
1975-05
实施



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号