25.100.70 磨料磨具 标准查询与下载

T/XXCCSS 009-2023 磨刀棒

本文件主要技术内容包括外观、尺寸、棒体磁性强度、磨削能力、耐腐蚀性、手柄连接强度、抗跌落等主要使用性能和安全要求。

Knife Sharpener

KS B 0431-2023 砂轮建议

Recommendation of grinding wheels

23/30456339 DC BS ISO 21538 超硬磨料切割轮毛坯 安装和固定孔 建筑施工和土木工程

BS ISO 21538. Blanks for superabrasive cutting-off wheels. Mounting and fixing bores. Building construction and civil engineering

23/30456333 DC BS ISO 603-9 固结磨具产品 尺寸 第 9 部分：高压磨削用砂轮

BS ISO 603-9. Bonded abrasive products. Dimensions - Part 9. Grinding wheels for high-pressure grinding

23/30456330 DC BS ISO 603-8 固结磨具产品 尺寸 第 8 部分：去毛刺和修整/勾丝用砂轮

BS ISO 603-8. Bonded abrasive products. Dimensions - Part 8. Grinding wheels for deburring and fettling/snagging

T/QGCML 762-2023 造粒金刚石堆积磨料制造工艺规范

本标准规定了造粒金刚石堆积磨料制造工艺规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于造粒金刚石堆积磨料的生产及检验。

Specification for manufacturing process of granulated diamond stacked abrasives

T/HEBQIA 145-2023 金刚石薄壁钻头

本文件规定了金刚石薄壁钻头的分类、规格尺寸、技术要求、试验方法、检验规则、标识、包装、运输和贮存。

Diamond thin wall drill bit

T/CFA 02020501042-2023 铸造熔炼用碳化硅

本文件规定了铸造熔炼用碳化硅（以下简称：碳化硅）的技术要求，试验方法，检验规则，标志、包装、贮存、运输及质量保证书。

Silicon carbide forsmelting of casting

KS B 0433-2022 精加工余量

Stock allowance for finish cut

KS L 6001-2022 粘结磨料粒度

Bonded abrasive grain sizes

KS L 6498-2022 研磨盘

Abrasive discs

KS L 6499-2022 橡胶切割轮

Rubber cutting-off wheels

KS L 6503-2022 砂轮试验方法

Test methods of grinding wheels

KS L ISO 15635-2022 涂层磨料.翻板

Coated abrasives — Flap discs

KS L 6500-2022 安装的车轮

Mounted wheels

ASTM G174-22 用磨料环接触测量材料耐磨性的标准试验方法

1.1 This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against aluminum oxide abrasive finishing tape. Though most solids can be tested, this test method addresses its use for metals, and coatings applied to metals. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

BS ISO 603-14:2022 固结磨料产品 尺寸 第14部分：角磨机上用于去毛刺和修整/勾丝的砂轮

1   Scope This document specifies the most common nominal dimensions, in millimetres, of: — shape type 6: straight cup grinding wheel; — shape type 11: taper cup grinding wheel; — shape type 27: depressed centre wheel for grinding or grinding/cutting-off; — shape type 28: depressed centre grinding wheel, concave shape; — shape type 29: depressed centre grinding wheel, convex shape. These bonded abrasive products are intended to be used for deburring and fettling/snagging of any surface of a workpiece using hand-held grinding machines (angle grinder). In this application, the workpiece is fixed and the grinding machine is guided by the operator. This document does not specify limit deviations and run-out tolerances, which are given in ISO 13942.

Bonded abrasive products — Dimensions - Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder

KS L ISO 603-18-2022 固结磨具产品尺寸第18部分：平板玻璃磨边机用砂轮

Bonded abrasive products — Dimensions — Part 18: Grinding wheels for flat glass edge grinding machines

KS L ISO 2421-2022 涂附磨具 圆柱形套筒

Coated abrasives — Cylindrical sleeves

KS L ISO 603-17-2022 固结磨料产品 尺寸 第17部分：主轴安装轮

Bonded abrasive products — Dimensions — Part 17: Spindle mounted wheels