共找到 1500 条与 磨料磨具 相关的标准,共 100 页
Synthesis of large single crystal diamond for industrial use by superabrasive static pressure method
Silicon carbide special products recrystallized silicon carbide square beam
Method for determination of compressive strength of superhard abrasives
Silicon carbide special products reaction sintered silicon carbide sagger
Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of volume resulting from abrasion of dimension stone as described in Terminology C119 and is based on Guide G195. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Exception—The formula for calculation of the result of this test method relies on the use of SI units; all measurements of weight in this test method shall be recorded in SI units. 1.2.2 Exception—As the equipment used in this test method was designed and initially fabricated using dimensions in inch-pound units, the values of equipment dimensions stated in SI units have been given as exact conversions to the nearest 0.1 mm. 1.3 This test method uses a rotary platform abraser to determine the loss in volume of dimension stone caused by abrasion under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
本标准规定了树脂结合剂薄片砂轮的形状及代号、基本尺寸和标记、基本要求、技术要求、试验方法、检验规则、包装、运输和贮存、质量承诺。 本标准适用于切割、开槽等用途,D≤400 mm的树脂结合剂薄片砂轮(以下简称砂轮),不适用于纤维增强树脂结合剂切割砂轮。
Bonded abrasive products—Resinoid bond flat grinding wheel
本标准规定了涂附磨具用高温煅烧棕刚玉磨料的代号、技术要求、试验方法、检验规则及包装、运输和贮存。 本标准适用于煅烧温度不低于1200℃的棕刚玉磨料(以下简称产品)。
Coated abrasives—High temperature calcined brown fused alumina
Bonded abrasive products — Dimensions — Part 5: Grinding wheels for surface grinding/face grinding
Glossary of terms and marks used in abrasive,grinding wheel and abrasive cloth and paper
Bonded abrasive products — Dimensions — Part 3: Grinding wheels for internal cylindrical grinding
Bonded abrasive products — Dimensions — Part 16: Grinding wheels for cutting-off on hand held power tools
Bonded abrasive products — Dimensions — Part 12: Grinding wheels for deburring and fettling on a straight grinder
Bonded abrasive products — Dimensions — Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines
Bonded abrasive products — Dimensions — Part 4: Grinding wheels for surface grinding/peripheral grinding
Bonded abrasive products — Dimensions — Part 2: Grinding wheels for centreless external cylindrical grinding
Bonded abrasive products — Dimensions — Part 1: Grinding wheels for external cylindrical grinding between centres
Bonded abrasive products — Dimensions — Part 6: Grinding wheels for tool and tool room grinding
Bonded abrasive products — Dimensions — Part 13: Grinding wheels for deburring and fettling on a vertical grinder
Bonded abrasive products — Dimensions — Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号