25.100.70 (Abrasives) 标准查询与下载

ASTM C1353/C1353M-15a 使用旋转平台磨料的脚部交通尺寸石材的耐磨性的标准测试方法

5.1 This test method provides a means to quantify the abrasion resistance of dimension stone and may be related to end-use performance, or used to comparatively rank material performance, or both. The resistance of dimension stone to abrasion, as measured on a testing machine in the laboratory, is generally only one of several factors contributing to wear performance as experienced in the actual use of the material. Calculation of predicted life should not be based on specific abrasion data alone. 5.2 The resistance of dimension stone to abrasion may be affected by factors including test conditions; type of abradant; pressure between the specimen and abradant; mounting of the specimen; and type, kind, or amount of finishing materials. 5.3 Abrasion tests utilizing the rotary platform abraser may be subject to variation due to changes in the abradant during the course of specific tests. Depending on abradant type and test specimen, the abrading wheel surface may change (that is, become clogged) due to pick-up of finishing or other materials from test specimens. To reduce this variation, the abrading wheels may require resurfacing. 1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of volume resulting from abrasion of dimension stone as described in Terminology C119 and is based on Guide G195. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Exception—The formula for calculation of the result of this test method relies on the use of SI units; all measurements of weight in this test method shall be recorded in SI units. 1.2.2 Exception—As the equipment used in this test method was designed and initially fabricated using dimensions in inch-pound units, the values of equipment dimensions stated in SI units have been given as exact conversions to the nearest 0.1 mm. 1.3 This test method uses a rotary platform abraser to determine the loss in volume of dimension stone caused by abrasion under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser

ASTM D2825-11 磨料及其相关材料的标准术语

Standard Terminology Relating to Polishes and Related Materials

ASTM C1353/C1353M-09e1 人行道用规格石料的耐磨损性的标准试验方法(旋转台式双头磨蚀机)

5.1 This test method provides a means to quantify the abrasion resistance of dimension stone and may be related to end-use performance, or used to comparatively rank material performance, or both. The resistance of dimension stone to abrasion, as measured on a testing machine in the laboratory, is generally only one of several factors contributing to wear performance as experienced in the actual use of the material. Calculation of predicted life should not be based on specific abrasion data alone. 5.2 The resistance of dimension stone to abrasion may be affected by factors including test conditions; type of abradant; pressure between the specimen and abradant; mounting or tension of the specimen; and type, kind, or amount of finishing materials. 5.3 Abrasion tests utilizing the rotary platform, double-head abraser may be subject to variation due to changes in the abradant during the course of specific tests. Depending on abradant type and test specimen, the abrading wheel surface may change (that is, become clogged) due to pick-up of finishing or other materials from test specimens. To reduce this variation, the abrading wheels may require resurfacing after use. 1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of volume resulting from abrasion of dimension stone as described in Terminology C119 and is based on Guide G195. 1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Exception—The formula for calculation of the result of this test method relies on the use of SI units; all measurements of weight in this test method shall be recorded in SI units. 1.2.2 Exception—As the equipment used in this test method was designed and initially fabricated using dimensions in inch-pound units, the values of equipment dimensions stated in SI units have been given as exact conversions to the nearest 0.1 mm. 1.3 This test method uses a rotary platform, double-head abraser to determine the loss in volume of dimension stone caused by abrasion under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform, Double-Head Abraser

ASTM C1353-09 人行道用规格石料的耐磨损性的标准试验方法(旋转台式双头磨蚀机)

This test method provides a means to quantify the abrasion resistance of dimension stone and may be related to end-use performance, or used to comparatively rank material performance, or both. The resistance of dimension stone to abrasion, as measured on a testing machine in the laboratory, is generally only one of several factors contributing to wear performance as experienced in the actual use of the material. Calculation of predicted life should not be based on specific abrasion data alone. The resistance of dimension stone to abrasion may be affected by factors including test conditions; type of abradant; pressure between the specimen and abradant; mounting or tension of the specimen; and type, kind, or amount of finishing materials. Abrasion tests utilizing the rotary platform, double-head abraser may be subject to variation due to changes in the abradant during the course of specific tests. Depending on abradant type and test specimen, the abrading wheel surface may change (that is, become clogged) due to pick-up of finishing or other materials from test specimens. To reduce this variation, the abrading wheels may require resurfacing after use.1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of volume resulting from abrasion of dimension stone as described in Terminology C119 and is based on Guide G195. 1.2 Units8212;The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 Exception8212;The formula for calculation of the result of this test method relies on the use of SI units; all measurements of weight in this test method shall be recorded in SI units. 1.2.2 Exception8212;As the equipment used in this test method was designed and initially fabricated using dimensions in inch-pound units, the values of equipment dimensions stated in SI units have been given as exact conversions to the nearest 0.1 mm. 1.3 This test method uses a rotary platform, double-head abraser to determine the loss in volume of dimension stone caused by abrasion under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform, Double-Head Abraser

ASTM C1353-08 使用旋转平台磨料的脚部交通尺寸石材的耐磨性的标准测试方法

1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone as described in Terminology C 119 and is modeled after Test Method C 501. 1.2 The values stated in metric units are to be regarded as the standard. 1.3 This test method makes use of a Taber abraser machine to determine the weight loss of dimension stone under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic

ASTM C1353-07 行人交通用规格石料的耐磨损性用泰伯磨损机的标准试验方法

1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone as described in Terminology C 119 and is modeled after Test Method C 501. 1.2 The values stated in metric units are to be regarded as the standard. 1.3 This test method makes use of a Taber abraser machine to determine the weight loss of dimension stone under controlled conditions.1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic

ASTM G174-04 磨擦环接触法测量材料耐磨性的标准试验方法

This test is useful for screening materials for use in tools that are subjected to abrasion from the material that is being machined, worked, or formed. It has been used to screen tool steels for punch press dies, hardfacings for earth-moving machinery, and wear coatings. This test utilizes a test that is simpler to build and use than those used in the Test Method G 132 abrasion test which, like this test, uses a fixed abrasive counterface to abrade a test material. The one-hour test is intended for metals and materials that are softer than hardened steel (67 HRC), but may be applied to harder materials (see 7.1.7).1.1 This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against a 30-956;m aluminum oxide abrasive finishing tape. Though most solids can be tested, this test method addresses its use for metals, and coatings applied to metals.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

ASTM G174-04(2009)e1 磨擦环接触法测量材料耐磨性的标准试验方法

This test is useful for screening materials for use in tools that are subjected to abrasion from the material that is being machined, worked, or formed. It has been used to screen tool steels for punch press dies, hardfacings for earth-moving machinery, and wear coatings. This is simpler to build and use than those used in the Test Method G 132 abrasion test which, like this test, uses a fixed abrasive counterface to abrade a test material. The one-hour test is intended for metals and materials that are softer than hardened steel (67 HRC), but may be applied to harder materials (see 7.1.7).1.1 This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against aluminum oxide abrasive finishing tape. Though most solids can be tested, this test method addresses its use for metals, and coatings applied to metals. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

ASTM G174-03 磨擦环接触法测量材料耐磨性的标准试验方法

1.1 This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against a 30-956;m aluminum oxide abrasive finishing tape. Though most solids can be tested, this test method addresses its use for metals, and coatings applied to metals.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact

ASTM D2825-02(2008) 磨料及相关材料的标准术语

Standard Terminology Relating to Polishes and Related Materials

ASTM C1353-98(2006) 行人交通用规格石料的耐磨损性用泰伯磨损机的标准试验方法

1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone as described in Terminology C 119 and is modeled after Test Method C 501. 1.2 The values stated in metric units are to be regarded as the standard. 1.3 This test method makes use of a Taber abraser machine to determine the weight loss of dimension stone under controlled conditions.1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic

ASTM C1353-98e1 用组合磨损器测定人行道用方石的耐磨性的标准试验方法

1.1 This test method covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone as described in Terminology C 119 and is modeled after Test Method C 501. 1.2 The values stated in metric units are to be regarded as the standard. 1.3 This test method makes use of a Taber abraser machine to determine the weight loss of dimension stone under controlled conditions. 1.4 This test method is useful in indicating the differences in abrasion resistance between the various dimension stones. This test method provides one element in comparing stones of the same type. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic

ASTM E1257-93(2008) 用光谱化学分析法评定表面处理用研磨材料的标准指南

The grinding materials used for the preparation of the surfaces of specimens prior to analysis by optical emission or X-ray emission spectroscopy can contaminate the surface and thus produce erroneous results. This guide provides examples of the effects of these contaminations and recommendations for evaluating grinding materials to eliminate or reduce these effects in spectrochemical analysis. The examples given in this guide are not the only contaminations which can occur. Especially in X-ray spectrometry, all phases of the surface preparation should be examined for potential contamination effects. Analytical significance of the contaminations observed depends on the needs of the analyst for the particular application at a given concentration level.1.1 This guide covers recommendations for the evaluation of various grinding materials used to prepare the surfaces of specimens to be analyzed by optical emission or X-ray emission spectroscopy. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Evaluating Grinding Materials Used for Surface Preparation in Spectrochemical Analysis

ASTM E1257-93(2003) 用光谱化学分析法评定表面处理用研磨材料

1.1 This guide covers recommendations for the evaluation of various grinding materials used to prepare the surfaces of specimens to be analyzed by optical emission or X-ray emission spectroscopy.1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Evaluating Grinding Materials Used for Surface Preparation in Spectrochemical Analysis