25.120.40 电化学加工机床 标准查询与下载

JIS B 6361-1:2017 机床.模具用放电加工机床(开模EDM)的试验条件.精度检验.第1部分:单柱机

Test conditions for die sinking electro-discharge machines (die sinking EDM) -- Testing of the accuracy -- Part 1: Single-column machines

EN 62841-3-13:2017 电动手持工具、移动式工具和草坪和园艺机械 安全 第 3-13 部分：移动式钻机的特殊要求

IEC 62841-3-13:2017 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. This Part 3-13 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication Key words: Drills, Hand-held tool, Safety

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-13: Particular requirements for transportable drills

JIS B 6032:2016 机床. 安全. 电火花线切割机

Machine tools -- Safety -- Electro-discharge machines

GOST ISO 28881-2016 机床安全. 电火花加工机床

Safety of machine tools. Electrodischarge machines

GSO ISO 11090-1:2015 放电金属铸造（EDM）设备试验条件精密试验 第1部分：单立柱设备（十字绘图仪工作台型和固定工作台型）

  Scope is not provided for this standard

Test conditions for die sinking electro-discharge machines (die sinking EDM) -- Testing of the accuracy -- Part 1: Single-column machines (cross-slide table type and fixed-table type)

GSO ISO 11090-2:2015 放电金属铸造（EDM）设备试验条件精密试验 第2部分：双轴设备（头滑块型）

  Scope is not provided for this standard

Test conditions for die sinking electro-discharge machines (die sinking EDM) -- Testing of the accuracy -- Part 2: Double-column machines (slide-head type)

KS B ISO 11090-2:2015 机床.发电加工机检查条件.术语和正确精密度检查.第2部分:双柱机(滑动头和十字工作台型)

Test conditions for die sinking electro-discharge machines(die sinking EDM) — Testing of the accuracy — Part 2: Double-column machines(slide-head type)

KS B ISO 11090-1:2015 机床.发电加工机检查条件.术语和正确精密度检查.第1部分:单立柱机床(十字型和固定工作台型)

Test conditions for die sinking electro-discharge machines(die sinking EDM) — Testing of the accuracy — Part 1: Single column machines(cross-slide table type and fixed table type)

BS ISO 14137:2015 电火花线切割机（电火花线切割机）的测试条件 准确性测试

Test conditions for wire electrical-discharge machines (wire EDM). Testing of the accuracy

BS ISO 11090-2:2014 电火花成形机 (电火花EDM) 的检验条件. 精度的检验. 双立柱机床 (移动主轴头型)

Test conditions for die sinking electro-discharge machines (die sinking EDM). Testing of the accuracy. Double-column machines (slide-head type)

BS ISO 11090-1:2014 电火花成形机 (电火花EDM) 的检验条件. 精度的检验. 单立柱机床 (十字工作台型和固定工作台型)

Test conditions for die sinking electro-discharge machines (die sinking EDM). Testing of the accuracy. Single-column machines (cross-slide table type and fixed-table type)

KS B ISO 11090-1:2014 机床.发电加工机检查条件.术语及正确精密度检查.第1部分:单立柱机床(十字型和固定工作台型)

Machine tools-Test conditions for die sinking electro-discharge machines(EDM)-Terminology and testing of accuracy-Part 1:Single column machines (cross slide table type and fixed table type)

KS B ISO 11090-2:2014 机床.发电加工机检查条件.术语及正确精密度检查.第2部分:双柱机(滑动头和十字工作台型)

Machine tools-Test conditions for die sinking electro-discharge machines(EDM)-Terminology and testing of accuracy-Part 2:Two column machines(slide-head type and cross-slide table type)

ISO 11090-1:2014 电火花成形机 (电火花EDM) 的检验条件. 精度的检验. 第1部分: 单立柱机床 (十字工作台型和固定工作台型)

This part of ISO 11090 specifies, with reference to ISO 230-1 and ISO 230-2, geometric and machining tests and tests for checking accuracy and repeatability of numerically controlled positioning axes for normal accuracy and general-purpose die sinking electro-discharge machines (die sinking EDM). It also specifies the applicable tolerances corresponding to the above-mentioned tests. This part of ISO 11090 is also applicable to single-column machines of cross-slide table type and fixed table type. This part of ISO 11090 deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.) or to the checking of its characteristics (such as speeds, feeds, etc.), which should generally be checked before the testing of the accuracy. This part of ISO 11090 provides the terminology used for the principal components of the machine and the designation of the axes with reference to ISO 841:2001. NOTE In addition to the terms used in the official ISO languages (English and French), Annex A of this part These are published under the responsibility of the national member bodies for Netherlands (NEN), Germany (DIN), Italy (UNI), Sweden (SIS), Iran (ISIRI), and Japan (JISC). However, only the terms given in the official languages can be considered as ISO terms.

Test conditions for die sinking electro-discharge machines (die sinking EDM) - Testing of the accuracy - Part 1: Single-column machines (cross-slide table type and fixed-table type)

ISO 11090-2:2014 冲模放电机（模具下沉EDM）的测试条件 - 精度测试 - 第2部分:双柱机（滑头型）

This part of ISO 11090 specifies, with reference to ISO 230-1 and ISO 230-2, geometric and machining tests and tests for checking accuracy and repeatability of numerically controlled positioning axes for normal accuracy and general-purpose die sinking electro-discharge machines (die sinking EDM). It also specifies the applicable tolerances corresponding to the above-mentioned tests. This part of ISO 11090 is applicable to double-column machines of slide-head type. This part of ISO 11090 deals only with the verification of accuracy of the machine. It does not apply to the testing of the machine operation (vibrations, abnormal noises, stick-slip motion of components, etc.) or to the checking of its characteristics (such as speeds, feeds, etc.), which should generally be checked before the testing of the accuracy. This part of ISO 11090 provides the terminology used for the principal components of the machine and the designation of the axes with reference to ISO 841:2001. NOTE In addition to the terms used in the official ISO languages (English and French), Annex A of this part These are published under the responsibility of the national member bodies for Netherlands (NEN), Germany (DIN), Italy (UNI), Sweden (SIS), Iran (ISIRI), and Japan (JISC). However, only the terms given in the official languages can be considered as ISO terms.

Test conditions for die sinking electro-discharge machines (die sinking EDM) — Testing of the accuracy — Part 2: Double-column machines (slide-head type)

DIN EN ISO 28881:2014 机床.安全性.电火花加工机械(ISO 28881-2013+Cor.1-2013).德文版本EN ISO 28881-2013+AC-2013

Machine tools - Safety - Electro-discharge machines (ISO 28881:2013 + Cor. 1:2013); German version EN ISO 28881:2013 + AC:2013

EN ISO 28881:2013/AC:2013 机床.安全性.电火花加工机械 包含修改件AC,2013

Machine tools - Safety - Electro-discharge machines - Technical Corrigendum 1 (ISO 28881:2013/Cor 1:2013)

EN ISO 28881:2013 机床.安全性.电火花加工机械

Diese internationale Norm legt technische Sicherheitsanforderungen und/oder Schutzmasnahmen welche fur EDM-Einrichtungen und EDM-Systeme anwendbar sind fest: manuell gesteuerte EDM-Senkerodiermaschinen und EDM-Bohrmaschinen numerisch gesteuerte EDM-Senkerodiermaschinen und EDM-Bohrmaschinen, und numerisch gesteuerte EDM-Drahterodiermaschinen die von Personen zu beachten sind, die mit der Auslegung, Konstruktion, Aufstellung und/oder Lieferung von diesen Einrichtungen befasst sind. Diese internationale Norm enthalt auch Informationen, die dem Anwender durch den Hersteller zur Verfugung gestellt werden mussen. Diese internationale Norm gilt nicht fur Maschinen zur Lichtbogenerosion und elektrochemischen Bearbeitungsmaschinen. Die in dieser internationalen Norm enthaltenen Anforderungen beziehen die bestimmungsgemase Verwendung unter ublichen Werkstattbedingungen in nicht explosionsfahiger Atmosphare einschlieslich Installation, Einrichten, Wartung, Reparatur und Demontage zur Standortanderung oder Entsorgung von EDM Einrichtungen mit ein. Diese internationale Norm gilt auch fur Zusatzeinrichtungen, die fur die EDM-Bearbeitung erforderlich sind. Diese internationale Norm behandelt spezifische Gefahrdungen, Gefahrensituationen oder gefahrliche Ereignisse welche im Zusammenhang mit EDM-Einrichtungen und EDM-Systemen, bei bestimmungsgemaser Verwendung und unter Bedingungen des Missbrauchs, welche fur den Hersteller vernunftigerweise vorhersehbar sind, stehen. (siehe Abschnitt 4) Diese Internationale Norm gilt fur Maschinen, die nach dem Ausgabedatum dieser Internationalen Norm hergestellt wurden.

Machine tools - Safety - Electro-discharge machines

DIN EN 12957:2009 机械工具安全性.放电加工机床(含修改件A1:2009),英文版本DIN EN 12957:2009-07

1.1 This standard specifies technical safety requirements and measures, applicable to EDM equipment and EDM system (e.g. for spark erosion-sinking, spark erosion-wire cutting), to be adopted by persons undertaking the design, construction, installation and/or supply of such equipment. This standard also includes information to be provided by the manufacturer to the user. 1.2 The design requirements of this standard shall not apply to arc eroding and electro chemical machining equipment. 1.3 This standard takes account of the intended use in normal workshop environment and non explosive atmospheres including installation, setting, maintenance, repair and dismantling for removal or disposal of EDM equipment. 1.4 This standard also applies to auxiliary devices essential for EDM processing. 1.5 This standard deals with specific hazards defined in clause 4, Table 1, and the measures of prevention in clause 5, Table 2. 1.6 This standard applies to machines built after its date of issue. NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.

Machine tools - Safety - Electro discharge machines (includes Amendment A1:2009); English version of DIN EN 12957:2009-07

LST EN 12957-2002+A1-2009 机床 安全 电火花机

Machine tools - Safety - Electro discharge machines