25.140.10 气动工具 标准查询与下载

ISO/DIS 11148-13:2023 手持式非电动工具 安全要求 第13部分：紧固件驱动工具

Hand-held non-electric power tools — Safety requirements — Part 13: Fastener driving tools

T/ZGWJHXH 40-2022 变压吸附型制氧机用膜片阀

本文件规定了变压吸附型制氧机用膜片阀的术语和定义、基本参数、基本要求、性能要求、试验方法、检验规则、标识、包装、贮存和质量承诺。 本文适用于额定压力不高于0.2MPa的制氧机用膜片式电磁阀。

Diaphragm valve for pressure swing adsorption oxygen generator

GSO ISO 11148-13:2022 手持式非电动工具 安全要求 第13部分：紧固件驱动工具

ISO 11148-13:2017 specifies safety requirements for hand-held non-electric power tools (hereinafter referred to as "fastener driving tools") intended for installation of a fastener (see Annex B), forming a mechanical connection or attachment with the workpiece which are for example wood and wood-based materials, plastic materials, fibre materials (loose or compacted), cementitious materials, metals and combinations of these materials. The fastener driving tools for fasteners can be powered by compressed air or combustible gases (which may be ignited by a battery or accumulator) and the energy is transmitted to an impacted element by an intermediary component that does not leave the device. These tools are intended to be used by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. ISO 11148-13:2017 is applicable to fastener driving tools in which energy is applied to a loaded fastener for the purpose of driving this into a workpiece. ISO 11148-13:2017 is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from powder-actuated cartridges, hydraulics or from any type of electrical supply. ISO 11148-13:2017 does not deal with special requirements and modifications of hand-held power tools for the purpose of mounting them in a fixture. ISO 11148-13:2017 deals with all significant hazards, hazardous situations or hazardous events relevant to fastener driving tools for fasteners when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of power tools in potentially explosive atmospheres. NOTE ISO 80079?36 gives requirements for non-electrical equipment for potentially explosive atmospheres.

Hand-held non-electric power tools — Safety requirements — Part 13: Fastener driving tools

ISO 28927-13:2022 便携式手提动力工具.振动发射评估的试验方法.第13部分:紧固件驱动工具

This document specifies a laboratory method for measuring the vibration at the handle of fastener driving tools. It is a type test procedure for establishing the vibration value on the handle of a hand- held power tool operating under a specified load. This document is applicable to fastener driving tools driven pneumatically or by other means, using nails, staples or pins. This document is applicable to tools with single sequential actuation, contact actuation, contact actuation with automatic reversion or continual contact actuation (see Figures 1 to 3). This document is not applicable to tools operating in full sequential mode due to their much longer intervals in between individual actuations. However, to provide an indication for comparison of different tools of this type (see Figures 4 and 5), Annex C provides informative guidance. NOTE Today current knowledge does not allow any conclusions regarding physiological and pathological effects between isolated shocks and continuous shock sequences, and their repetition rates.

Hand-held portable power tools — Test methods for evaluation of vibration emission — Part 13: Fastener driving tools

T/ZZB 2184-2021 平行型手指气缸

本文件规定了平行型手指气缸的术语和定义、基本要求、分类及基本参数、技术要求、试验方法、检验规则、标识、包装、运输及贮存和质量承诺。 本文件适用于以压缩空气为介质,工作压力为 0.1 MPa～1.0 MPa，缸径为 6 mm～40 mm 的平行型手指气缸。

Parallel finger cylinders

T/WLJC 29-2020 涡流热风油漆风干枪

油漆风干枪是以压缩空气为气源的漆面风干设备，产品结构新颖，构思巧妙，易于使用。广泛应用于汽车行业、家具行业的喷涂后的漆面风干。 经检索，在油漆风干枪（烘干枪）技术领域，没能有制定国家标准和行业标准，也没有相关的国际标准和国外先进标准。 本标准规定了涡流热风油漆风干枪的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存，适用于以压缩空气为动力源，使压缩空气通过涡流管加热的油漆风干枪。

Vortexhotairpaintdryinggun

T/WLJC 28-2020 环保型低压喷漆枪

环保型低压喷漆枪是低压气动的喷漆装置，油漆的传递效率能达到60%以上，有效地降低挥发涂料带来对环境的污染。参照欧盟的环保型水性油漆喷枪的先进技术，是国内首创的新产品。 本技术领域现有JB/T 13280 气动喷漆枪、DB 35/T 967-2009 气动喷漆枪和JIS B9809 喷漆枪等标准，不能满足环保型气动喷漆枪的检验及试验等需要。 本标准规定了气动喷漆枪的术语和定义、基本要求、产品型号和结构、性能参数、技术要求、检验方法、检验规则、标志、包装、运输、贮存，适用于以压缩空气为动力源，采用低进气压力的气动喷漆枪（简称产品）的设计、制造、验收与使用。

Environment-friendly spray guns

T/ZGWJHXH 38-2020 医院PM2.5调控净化系统

本标准规定了“医院PM2.5调控净化系统”的术语、符号和定义，分类、命名和标记，技术参数、技术要求、检验方法、检测规则、标志、包装、运输和贮存要求等。

Hospital PM2.5 regulation and purification system

T/ZGWJHXH 37-2020 幼儿园氧气调控净化系统

本标准规定了“幼儿园氧气控制净化系统”的术语、符号和定义，分类、命名和标记，技术参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存要求等。 本标准适用于中国五金交电化工商业协会生产、销售净化系统的会员单位。其它生产、销售净化系统的单位，可参照执行。

Kindergarten oxygen control and purification system

T/ZGWJHXH 42-2020 环室取压的焊接孔板流量计安全技术

本标准规定了用于压力管道公称直径大于等于50mm并且小于等于1000mm的环室取压焊接孔板流量计的材料、设计、制造、检验等环节的技术要求。 本标准仅适用于在整个测量段内保持亚音速流动、且可被认为是单项的流体。

Safety Technology of Welded Orifice Plate Flowmeter for Pressure Gathering in Annular Chamber

T/ZGWJHXH 39-2020 流量计环室短节环向对接接头超声检测

本标准规定了流量计环室短节环向对接接头采用A型脉冲反射式超声检测仪检测工件缺陷的检测方法和质量分级要求。 本标准适用于同时具备下列条件的焊接接头： a) 母材为低碳钢或低合金钢； b) 全焊透结构型式的环向对接接头； c) 焊缝为铁素体成分时，适用工件厚度 t:6 mm≤t≤150 mm，且焊缝两侧工件厚度相同； 焊缝含奥氏体成分时，适用工件厚度 t:10 mm≤t≤80 mm，且焊缝两侧工件厚度相同； d) 外径 D0:D0≥159 mm。 1.3  流量计的其他对接接头超声检测，也可参照本标准实施。

Ultrasonic Testing of Annular Butt Joints of Flowmeter Annular Chamber Subsections

JB/T 13956-2020 燃气动力射钉枪用气罐

Gas tank for gas powered nail gun

JB/T 13951-2020 冲击式气螺刀

Impact air screwdriver

JB/T 13952-2020 气动注油机

Pneumatic oiling machine

JB/T 13955-2020 燃气动力射钉枪

Gas Powered Nail Gun

T/ZGWJHXH 34-2020 电站锅炉用长颈喷嘴流量计安全技术

本标准规定了额定工作压力大于等于3.8MPa且小于16.7MPa蒸汽锅炉上用于测量蒸汽或者给水流量的长颈喷嘴流量计的材料、设计、制造、检验等环节的技术要求，此范围以外的长颈喷嘴流量计也可参考本标准执行。

Safety Technology of Long-neck Nozzle Flowmeter Used in Power Plant Boiler

T/ZZB 1649-2020 低压气动喷漆枪

本标准规定了低压气动喷漆枪的术语和定义、基本要求、产品型号和结构、性能参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存及质量承诺。 本标准适用于以压缩空气为动力源，采用低进气压力,进气压力≤0.25 Mpa的气动喷漆枪（以下简称产品）。

Low pressure air spray guns

ISO 28927-1:2019 便携式手提式电动工具振动辐射评定试验方法第1部分:角向和立式磨床

This document specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no-load conditions. The method has been established for surface grinding tasks only. Cutting and sanding generally create lower vibrations. It is intended that the results be used to compare different models of the same type of machine. This document is applicable to hand-held machines (see Clause 5), driven pneumatically or by other means, intended for grinding, cutting-off and rough sanding, with bonded, coated and super-abrasive products and with wire brushes for use on all kinds of materials. It is not applicable to die grinders or straight grinders. NOTE To avoid confusion with the terms “power tool” and “inserted tool”, machine is used for the former throughout this document.

Hand-held portable power tools — Test methods for evaluation of vibration emission — Part 1: Angle and vertical grinders

T/ZGWJHXH 23-2019 气动弹涂枪

本标准规定了气动弹涂枪的术语和定义、型号编制、基本参数、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以压缩空气为动力使用高粘度液体为介质的气动弹涂枪的设计、制造、验收与使用。

Pneumatic spray gun

ISO 28927-8:2009/Amd 2:2019 手持式便携式电动工具 振动发射评估试验方法 第8部分：往复式锯、抛光和锉磨机以及摆动或旋转式小型锯

Hand-held portable power tools — Test methods for evaluation of vibration emission — Part 8: Saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating a