25.160.30 焊接设备 标准查询与下载

T/GDMES 0009.1-2021 激光焊接设备 透射塑料激光焊接设备

本文件规定了透射塑料激光焊接设备的术语与定义、基本要求、技术要求、试验方法、检验规则、标志、随机文件、包装、运输、储存。

Laser welding machine — Laser transmission welding machine for plastics

T/GDMES 0009.2-2021 激光焊接设备 透明塑料激光焊接设备

本文件规定了透明塑料激光焊接设备的术语与定义、基本要求、技术要求、试验方法、检验规则、标志、随机文件、包装、运输、储存。

Laser welding machine — Laser welding machine for transparent plastics

T/STIC 110062-2021 直流手工弧焊机

本文件规定了直流手工弧焊机的使用要求、技术要求、试验方法、检验规则和铭牌、标识、包装、运输及贮存。 本文件适用于为工业和专业用途而设计的由不超过GB/T 156标准中表1规定的电压供电或由机械设备驱动的额定电流为160A~800A的直流手工弧焊机。

DC Manual Arc Welding Machine

PN-EN ISO 10225-2021-08 E 气焊设备 用于气焊、切割和相关工艺的设备的标记（ISO 10225:2013）

Gas welding equipment -- Marking for equipment used for gas welding, cutting and allied processes (ISO 10225:2013)

T/ZZB 2206-2021 电机定子铁芯激光焊接装备

本文件规定了电机定子铁芯激光焊接装备的术语和定义、基本要求、工作条件、技术要求、试验方法、检验规则、标志、包装、随机文件和附件、运输、贮存和质量承诺。 本文件适用于内径范围为φ100 mm～φ190 mm、 外径范围为φ140 mm～φ300 mm、 高度范围为100 mm～250 mm的电机定子铁芯的多工位激光焊接装备（以下简称“焊接装备”）。

Laser welding equipment for motor stator core

KS B 6354-2021 用于切割、加热及相关工艺的液化石油气调压器

LP－GAS pressure regulators used in cutting,heating and related processes

OENORM EN ISO 10225:2021 气焊设备 用于气焊、切割和相关工艺的设备的标记（ISO 10225:2013）

Gas welding equipment - Marking for equipment used for gas welding, cutting and allied processes (ISO 10225:2013)

DS/ISO 8167:2021 电阻焊 压花凸焊 电阻焊凸出

Resistance welding – Embossed projection welding – Projections for resistance welding

DS/EN ISO 8167:2021 电阻焊 压花凸焊 电阻焊凸出物（ISO 8167:2021）

Resistance welding – Embossed projection welding – Projections for resistance welding (ISO 8167:2021)

BS EN IEC 60974-13:2021 电弧焊设备. 第13部分: 焊接回流夹

Arc welding equipment. Welding current return clamp

PN-EN ISO 7285-2021-07 E 机械化多点焊用气缸（ISO 7285:1995）

Pneumatic cylinders for mechanized multiple spot welding (ISO 7285:1995)

DS/EN IEC 60974-13:2021 弧焊设备第13部分：焊接电流回流钳

Arc welding equipment – Part 13: Welding current return clamp

GSO ISO 15616-3:2021 用于高质量焊接和切割的 CO2 激光束机器的验收测试 第3部分：气体流量和压力测量仪器的校准

ISO 15616-3:2003 is applicable to the measurement of the process-oriented gas parameters for the acceptance tests for CO2-laser beam machines for high quality welding and cutting in two operation directions in accordance with ISO 15616-1:2003. This international Standard specifies examination procedures for instruments used for control of process-oriented gas parameters.

Acceptance tests for CO2-laser beam machines for high quality welding and cutting — Part 3: Calibration of instruments for measurement of gas flow and pressure

GSO IEC 62822-1:2021 电焊设备 与人体暴露于电磁场（0 Hz 至 300 GHz）相关的限制评估 第1部分：产品系列标准

IEC 62822-1:2016 is a product family standard, applies to equipment for resistance welding, arc welding and allied processes designed for occupational use by professionals and for use by laymen.

Electric welding equipment - Assessment of restrictions related to human exposure to electromagnetic fields (0 Hz to 300 GHz) - Part 1: Product family standard

GSO IEC 62822-2:2021 电焊设备 与人体暴露于电磁场（0 Hz 至 300 GHz）相关的限制评估 第2部分：弧焊设备

IEC 62822-2:2016 applies to equipment for arc welding and allied processes designed for occupational use by professionals and for use by laymen.

Electric welding equipment - Assessment of restrictions related to human exposure to electromagnetic fields (0 Hz to 300 GHz) - Part 2: Arc welding equipment

GSO ISO 17662:2021 焊接 用于焊接的设备的校准、验证和确认 包括辅助活动

ISO 17662:2016 specifies requirements for calibration, verification and validation of equipment used for - control of process variables during fabrication, and - control of the properties of equipment used for welding or welding allied processes where the resulting output cannot be readily or economically documented by subsequent monitoring, inspection and testing. This involves process variables influencing the fitness-for-purpose and in particular the safety of the fabricated product. NOTE 1 This International Standard is based on the lists of process variables stated in International Standards for specification of welding procedures, in particular, but not exclusively in the ISO 15609‑ series. Future revisions of these International Standards can result in addition or deletion of parameters considered necessary to specify. Some guidance is, in addition, given in Annex B as regards requirements for calibration; verification and validation as part of acceptance testing of equipment used for welding or allied processes. Requirements to calibrate, verify and validate as part of inspection, testing, non-destructive testing or measuring of final welded products performed in order to verify confirm product compliance are outside the scope of the present International Standard. The subject of this International Standard is limited to calibration, verification and validation of equipment after installation, as part of the workshops' and site operations for maintenance and/or operation. It needs to be stressed that this International Standard has nothing to do with manufacture and installation of equipment for welding. Requirements for new equipment are formulated in directives and product codes (standards), as necessary. Annex C provides information when other parties are involved in calibration, verification and validation activities.

Welding — Calibration, verification and validation of equipment used for welding, including ancillary activities

EN ISO 8167:2021 电阻焊用凸出部位

Resistance welding - Embossed projection welding - Projections for resistance welding (ISO 8167:2021)

BS EN IEC 60974-11:2021 弧焊设备 电极支架

Arc welding equipment. Electrode holders

LST EN ISO 8205:2021 电阻焊设备-水冷二次连接电缆（ISO 8205:2021）

Resistance welding equipment - Water-cooled secondary connection cables(ISO 8205:2021)

IEC 60974-1:2021 RLV 弧焊设备第1部分:焊接电源

Arc welding equipment - Part 1: Welding power sources