25.160.40 焊接接头 标准查询与下载

KS B ISO 9016-2021 金属材料焊接的破坏性试验 - 冲击试验 - 试样位置 凹口取向和检验

Destructive tests on welds in metallic materials — Impact tests —Test specimen location, notch orientation and examination

BS ISO 23864:2021 焊缝无损检测 超声波检测 自动全聚焦技术（TFM）和相关技术的使用

Non-destructive testing of welds. Ultrasonic testing. Use of automated total focusing technique (TFM) and related technologies

EN 12814-8:2021 热塑性半成品焊接接头试验.第8部分:要求

Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements

ISO 23864:2021 焊接无损检测. 超声检测. 自动全聚焦技术(TFM)和相关技术的使用

This document specifies the application of the TFM technique and related technologies for semi- or fully automated ultrasonic testing of fusion- welded joints in metallic materials of minimum thickness 3,2 mm. NOTE Unless stated otherwise, in this document ‘TFM” and ‘TFM technique” refer to the TFM technique as defined in ISO 23243, and to all related technologies, see for example ISO 23865 and ISO 23243. This document is applicable to components with welds fabricated using metals which have isotropic (constant properties in all directions) and homogeneous conditions. This includes welds in low carbon alloy steels and common aerospace grade aluminium and titanium alloys, provided they are homogeneous and isotropic. This document applies to full penetration welded joints of simple geometry in plates, pipes and vessels. This document specifies four testing levels (A, B, C, D), each corresponding to a different probability of detection of imperfections. Guidance on the selection of testing levels is provided. Coarse-grained metals and austenitic welds can be tested when the provisions of this document have been taken into account. This document gives provisions on the specific capabilities and limitations of the TFM technique for the detection, locating, sizing and characterization of discontinuities in fusion-welded joints. The TFM technique can be used as a stand-alone approach or in combination with other non-destructive testing (NDT) methods for manufacturing, in-service and post-repair tests. This document includes assessment of indications for acceptance purposes based on either amplitude (equivalent reflector size) and length or height and length. This document does not include acceptance levels for discontinuities. The following two typical testing techniques for welded joints are referred to in this document: a) side scanning, where the probe(s) is (are) positioned adjacent to the weld cap, typically using wedges. Side scanning can be performed from one side or both sides of the weld; b) top scanning where the probe is positioned on top of weld cap with a flexible, conformable delay line or using immersion technique, or using contact technique after removing the weld cap. Semi-automated testing encompasses a controlled movement of one or more probes along a fixture (guidance strip, ruler, etc.), whereby the probe position is measured with a position sensor. The scan is performed manually. In addition, fully automated testing includes mechanized propulsion.  1 

Non-destructive testing of welds - Ultrasonic testing - Use of automated total focusing technique (TFM) and related technologies

ISO 23598:2021 板材的机械连接. 接头的破坏性试验. 单接头的机械剥离试验的试样尺寸和程序

This document specifies the geometry of test specimens and the testing procedure for mechanized peel testing of single mechanical joints on single-lap test specimens up to a single sheet thickness of 4,5 mm. The term “sheet”, as used in this document, includes extrusions and cast materials. The purpose of the mechanized peel tests is to determine the mechanical characteristics and the failure modes of the joints made with different joining methods. This document does not apply to civil engineering applications such as metal buildings and steel constructions which are covered by other application standards. NOTE For mechanized peel testing of resistance spot, seam and embossed projection welds, see ISO 14270

Mechanical joining of sheet materials - Destructive testing of joints - Specimen dimensions and procedure for mechanized peel testing of single joints

EN ISO 18785-2:2021 摩擦搅拌点焊 - 铝 - 第2部分:焊缝设计

Friction stir spot welding - Aluminium - Part 2: Design of weld joints (ISO 18785-2:2018)

EN 12814-2:2021 热塑性塑料半成品的焊接接头试验.第2部分:拉伸试验

Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test

ISO 13919-2:2021 电子和激光束焊接接头. 缺陷质量等级的要求和建议. 第2部分: 铝,镁及其合金和纯铜

This document gives guidance on levels of imperfections in electron and laser beam welded joints in aluminium, magnesium and their alloys and pure copper. Three levels are given in such a way as to permit application for a wide range of welded fabrications. The levels refer to production quality and not to the fitness-for-purpose of the product manufactured. This document applies to electron and laser beam welding of: — aluminium and its alloys; — magnesium and its alloys; — pure copper (e.g. Cu-ETP1 CW003A, Cu-ETP CW004A, Cu-FRHC CW005A, Cu-FRTP CW006A, Cu-OF1 CW007A, Cu-OF CW008A, Cu-OFE CW009A, Cu-PHC CW020A, Cu-HCP CW021A, Cu-PHCE CW022A, Cu-DLP CW023A, Cu-DHP CW024A); — all types of welds welded with or without additional filler wire; — materials equal to or above 0,5 mm thickness for electron and laser beam welding. When significant deviations from the joint geometries and dimensions stated in this document are present in the welded product, it is necessary to evaluate to what extent the provisions of this document can apply. NOTE For circular welds, a lower quality level can be specified for the fade-out zone. Metallurgical aspects, e.g. grain size, hardness, hydrogen embrittlement (pure copper) are not covered by this document. This document is directly applicable to visual examination of welds and does not include details of recommended methods of detection or sizing by other non-destructive means. There are difficulties in using these limits to establish appropriate criteria applicable to non-destructive testing methods, such as ultrasonic, radiographic and penetrant testing, and they can need to be supplemented by requirements for inspection, examination and testing.

Electron and laser-beam welded joints - Requirements and recommendations on quality levels for imperfections - Part 2: Aluminium, magnesium and their alloys and pure copper

GOST R 59399-2021 热塑性塑料焊接接头的缺陷 质量等级

Imperfections in thermoplastics welded joints. Quality levels

GOST R 59398-2021 热塑性塑料焊接接头的缺陷 分类

Imperfections in thermoplastic welded joints. Classification

GOST R ISO 6520-2-2021 焊接及相关工艺 金属材料几何缺陷的分类 第2部分. 压力焊接

Welding and allied processes. Classification of geometric imperfections in metallic materials. Part 2. Welding with pressure

GOST R ISO 5817-2021 焊接 钢材、镍、钛及其合金的电容焊(不包含电子束焊)接点 缺陷质量级别

Welding. Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded). Quality levels

ASTM A928/A928M-14(2021) 添加填充金属的电熔焊铁素体/奥氏体（双相）不锈钢管的标准规范

1.1 This specification covers electric-fusion-welded steel pipe suitable for corrosive service. NOTE 1—The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for traditional terms such as nominal diameter, size, and nominal size. 1.2 This specification covers grades of ferritic/austenitic steel as indicated in Table 1. The selection of the proper alloy and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered. 1.3 Five classes of pipe are covered as follows: 1.3.1 Class 1—Pipe shall be double welded by processes using filler metal in all passes and shall be radiographed completely. 1.3.2 Class 2—Pipe shall be double welded by processes using filler metal in all passes. No radiograph is required. 1.3.3 Class 3—Pipe shall be single welded by processes using filler metal in all passes and shall be radiographed completely. 1.3.4 Class 4—Same as Class 3, except that the weld pass exposed to the inside pipe surface is permitted to be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2). 1.3.5 Class 5—Pipe shall be double welded by processes using filler metal in all passes and shall be spot radiographed. 1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S4 are included as options to be specified in the purchase order when desired. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of the specification is specified in the order. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal

PN-EN ISO 17640-2019-01 P 焊缝无损检测 超声波检测 技术、检测水平和评估（ISO 17640:2018）

Non-destructive testing of welds -- Ultrasonic testing -- Techniques, testing levels, and assessment (ISO 17640:2018)

PN-EN ISO 10863-2020-12 E 焊缝无损检测 超声波检测 使用飞行时间衍射技术（TOFD）（ISO 10863:2020）

Non-destructive testing of welds -- Ultrasonic testing -- Use of time-of-flight diffraction technique (TOFD) (ISO 10863:2020)

ASTM E390-20 钢熔焊标准参考射线照相

1.1 This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The reference radiograph films are an adjunct to this standard and must be purchased separately from ASTM International if needed. 1.2 There are three volumes of reference radiographs based on seven nominal weld thicknesses as follows: Vol I—Set of 16 plates (81⁄2 by 11 in.) covering base material up to and including 1⁄4 in. (6.4 mm) in thickness. Vol II—Set of 29 plates (81⁄2 by 11 in.) covering base material over 1⁄4 up to and including 3 in. (6.4 to 76 mm) in thickness. Vol III—Set of 32 plates (81⁄2 by 11 in.) covering base material over 3 up to and including 8 in. (76 to 203 mm) in thickness. 1.3 From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard. 1.4 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Reference Radiographs for Steel Fusion Welds

ASTM E1955-20 通过与分级ASTM（astmref rid =“a00002”/>参考射线照片）比较的钢中焊缝的良好的标准射线照相检查

1.1 This standard covers requirements for radiographic examination for soundness of welds in fabricated steel by comparison to selected severity levels of Reference Radiographs E390, Vol II. The base material varies from greater than 0.25 to 3 in. (6.4–76 mm) inclusive in thickness. Volume II is applicable. This standard is not suitable for shipyard use. NOTE 1—This standard was adopted to replace Mil-Std. 1264-B, entitled “Radiographic Inspection For Soundness of Welds In Steel By Comparison To Graded ASTM E390 Reference Radiographs,” dated 18 January, 1989. This standard is intended to be used for the same applications as the document which it replaced. Users should carefully review its requirements when considering the standard’s use for new and/or different applications. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Radiographic Examination for Soundness of Welds in Steel by Comparison to Graded ASTM Reference Radiographs

KS B 0888-2020 无损检测方法进行管道焊接的

Non-destructive testing for welded joint of pipeline

KS B 0897-2020 超声波斜束检验方法铝板的对接焊缝

Ultrasonic testing for butt welded joint of aluminium plates using shear wave angle beam

KS B 0896-2020 超声检查为铁素体钢的焊接的方法

Ultrasonic testing for welded joints of ferritic steel