25.180.10 电炉 标准查询与下载

GB/T 6542-1986 直接电弧炉的试验方法

本标准适用于额定容量等于或大于0.5t的工业用三相直接电弧炉。这类炉子既适用于固态炉料，也适用于液态炉料，工作时炉内气压等于或接近于大气压。 本标准中除了特别指明是三相电弧炉的条款之外，其他条款也适用于一个或多个电极的电弧炉。 这些电炉用来熔炼黑色金属（钢、铸铁）和有色金属（铜）；也可作为保温炉供液态炉料在浇铸前的过热和保温用。 注：所有电气试验都要排除无功功率补偿和（或）电压稳定装置的影响。如果在试验期间不能关断这些装置，则 本标准中有关主电路的各条仍然适用，只是应指出无功功率补偿装置和（或）电压稳定装置也同时投入工作， 并须补充说明适用的供电网和这类装置的影响。

Test methods for direct arc furnaces

GB 5959.1-1986 电热设备的安全 第1部分:通用要求

本标准适用于各类工业电热设备，例如：直接电弧炉、埋弧炉、其他电弧加热设备、电渣重熔炉、等离子加热设备、感应熔炼炉、感应加热设备、电阻炉、红外辐射加热设备、高频介质加热设备、具有电子枪的电热设备、微波加热设备和激光加热设备。 本标准不适用于家用烹调和加热用电气用具、焊接设备和取暖加热系统。对电热设备的安全要求，包括适用于所有电热设备的《通用要求》和分别适用于各类电热设备的《特殊要求》。本标准只是适用于所有电热设备的《通用要求》。 这些标准不仅适用于电热设备的正常运行状态，也考虑到在误操作和设备发生故障时，能确保人身安全。

Safety in electroheat installations--Part 1: General requirements

BS EN IEC 60519-6:2024 电加热和电磁加工装置的安全 高频介电和微波加热和加工设备的特殊要求

Safety in installations for electroheating and electromagnetic processing - Particular requirements for high frequency dielectric and microwave heating and processing equipment

T/EJCCCSE 035-2024 生产抗氧化合金锡焊料熔炉技术规范

5.1    外观要求 5.2    性能要求 5.3　 功能要求  5.4    安全要求

Technical specifications for furnaces for producing antioxidant tin solder alloys

BS EN IEC 60676:2024 工业电加热设备 直接电弧炉试验方法

Industrial electroheating equipment. Test methods for direct arc furnaces

FprEN IEC 60676:2023 工业电加热设备 直接电弧炉试验方法

IEC 60676:2024 This document specifies the basic test procedures, conditions and methods for establishing the main performance parameters and the main operational characteristics of furnaces for direct arc heating, forming arcs between the electrode and metal, such as electric arc furnaces using alternating current (EAF AC) or direct current (EAF DC), and ladle furnaces (LF), with rated power level above 500 kVA . This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The structure has been redrafted according to IEC 60398:2015. b) The scope has been redrafted. c) The terms/definitions, normative references and bibliography have been updated and completed. d) The test methods and content from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF). e) The annexes from IEC 60398:2015 have been confirmed, replaced, or complemented with regards to direct arc furnaces (EAF, LF).

Industrial electroheating equipment - Test methods for direct arc furnaces

GSO IEC 60519-6:2024 电加热和电磁处理装置的安全 第6部分：高频电介质和微波加热和处理设备的特殊要求

IEC 60519-6:2022 is applicable to equipment using high frequency or microwave energy alone or in combination with other kinds of energy for industrial heating and processing of materials. It is also applicable to HF and MW generators made available to users as separate units. This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: the structure has been redrafted according to the IEC 60519-1:2020; the scope and object have been redrafted; the terms/definitions, normative references and bibliography have been updated and completed; all requirements and content from IEC 60519-6:2011 which are included in IEC 60519-1:2020 were removed to avoid any duplication; inclusion of high frequency equipment which was previously covered by IEC 60519-9:2005 (withdrawn). This edition constitutes an extension to high frequency equipment.

Safety in installations for electroheating and electromagnetic processing - Part 6: Particular requirements for high frequency dielectric and microwave heating and processing equipment

JB/T 14461-2023 炼钢电弧炉工业节能评估技术要求

Technical requirements for industrial energy conservation assessment of steelmaking electric arc furnaces

T/CEEIA 769-2023 全自动硅单晶炉

本文件规定了全自动硅单晶炉的产品分类、基本参数、技术要求，界定了相应的术语和定义，描述了相应的试验方法，规定了检验规则、标志、包装、运输和贮存、订购与供货等。 本文件适用于光伏用电阻加热直拉法全自动硅单晶炉（以下简称“单晶炉”）。

Fully automatic silicon single crystal furnaces

T/CIECCPA 059-2023 高压感应加热熔盐装置

本文件规定了可直接接入高压电力系统运行的，利用电磁感应加热原理对熔盐快速加热的装置（称为高压感应加热熔盐装置，以下简称感应加热熔盐装置）的组成部分、技术要求、试验方法、标志、包装、运输和贮存。 本文件适用于接入电压6kV～35kV及以上、加热功率500kW及以上适用于熔盐电储热领域的高效、稳定的感应加热熔盐装置。 本文件不适用于通过降压变压器或者感应加热电源，将系统电压降低后再输出到感应加热器的感应加热熔盐装置。

High voltage induction heating molten salt installations

T/QGCML 2114-2023 锂电池真空干燥炉

本文件规定了锂电池真空干燥炉的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于软包、圆柱、铝壳等类型锂离子电池使用的电池真空干燥炉，以下简称“干燥炉”。

Lithium battery vacuum drying oven

T/QGCML 2115-2023 锂电池预热隧道炉

本文件规定了锂电池预热隧道炉的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于卷绕之后的裸电芯（JR）在整形之前的预热，以便能使裸电芯快速预热、提高产能的锂电池预热隧道炉，以下简称“隧道炉”。

Lithium battery preheating tunnel furnace

T/CEEIA 698-2023 热处理电阻炉质量分级规范

本文件规定了热处理电阻炉的质量分级原则、分级指标、抽样检验方法、判定和文档管理。 本文件适用于井式电阻炉、箱式电阻炉、台车式电阻炉、箱式淬火电阻炉、电热浴炉、推送式电阻加热机组（以下简称推送炉机组）等常见典型炉型的热处理电阻炉的质量分级活动。

Specifications for quality grade of heat treatment resistance furnaces

T/CEEIA 697-2023 铸造感应炉质量分级规范

本文件规定了铸造感应炉的质量分级原则、分级指标、抽样检验方法和文档管理。 本文件适用于工作频率高于工频50 Hz，低于或等于1000 Hz，额定容量在1 t~60 t范围内，由中频半导体变频装置供电，无心感应铸铁（钢）熔化炉、无心感应铜及其合金熔化炉、无心感应铝熔化炉和无心感应锌熔化炉的质量分级活动。 本文件也适用于没有变频装置，直接使用工业电网频率50 Hz或60 Hz电源供电的无心感应炉和有心感应熔铜（铝、锌）炉的质量分级活动。

Specifications for quality grade of foundry induction furnaces

T/QGCML 711-2023 光波远红外石英加热管

本文件规定了光波远红外石英加热管的术语和定义、要求、检验方法、检验规则、标志、包装、运输和贮存。 本文件适用于光波远红外石英加热管的生产和检验。

Light wave far infrared quartz heating tube

ASTM D5513-22 痕量素分析用工业炉供入液流的微波溶解标准实施规范

1.1 This practice describes the multi-stage microwave digestion of typical industrial furnace feed stream materials using nitric, hydrofluoric, hydrochloric, and boric acids for the subsequent determination of trace metals. 1.2 This practice has been used successfully on samples of coal, coke, cement raw feed materials, and waste-derived fuels composed primarily of waste paint-related material in preparation for measuring the following trace elements: Ag, As, Ba, Be, Cd, Cr, Hg, Pb, Sb, and Tl. This practice may be applicable to elements not listed above. 1.3 This practice is also effective for other waste materials (for example, fly ash, foundry sand, alum process residue, cement kiln dust, etc.). 1.4 The values stated in SI units are to be regarded as standard. Other units of measurement in parentheses in this standard are informational. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Microwave Digestion of Industrial Furnace Feed Streams and Waste for Trace Element Analysis

ASTM A1100-16(2022) 感应热处理鉴定与控制指南

1.1 This guide covers the process control and product properties verification of continuous heat treating of material using a quench and temper induction process (surface hardening, surface heat treating, and batch heat-treated products using induction are not considered in this guide). Examples of products covered by this guide may include products covered by API Specifications 20E, 5L, and 5CT. 1.2 This guide indicates some features of induction heat treating compared to furnace heat treating. Induction heat treating processes typically operate at higher temperatures compared to furnace processes. 1.3 This guide addresses the features and requirements necessary for induction heating and ancillary equipment. However, induction equipment may be used in combination with convection heating equipment (for example, gas or electric furnaces). 1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Qualification and Control of Induction Heat Treating

KS C IEC 60703-2022 电子枪电加热装置的试验方法

Test methods for electroheating installations with electron guns

KS C IEC 60519-7-2022 电热装置的安全 第7部分：电子枪装置的特殊要求

Safety in electroheat installations－Part 7：Particular requirements for installations with electron guns

KS C IEC 61308-2022 高频介质加热装置 测定功率输出的试验方法

High-frequency dielectric heating installations－Test methods for the determination of power output