25.220.10 标准查询与下载

DIN EN ISO 8501-4:2021 涂料和有关产品涂覆之前钢基片的制备. 表面清洁度的目视评估. 第4部分: 与水冲法有关的初始表面条件、制备等级和闪锈等级(ISO 8501-4-2020); 德文版本EN ISO 8501-4-2020

This part of DIN EN ISO 8501 specifies a series of preparation grades of steel surfaces after removal of water-soluble contaminants, rust and coatings as well as other foreign matter by high-pressure water jetting.

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with water jetting (ISO 8501-4:2020);

LST EN ISO 11127-4:2021 涂装油漆和相关产品前钢基材的制备 非金属喷砂清理磨料的试验方法 第4部分：通过载玻片试验评估硬度（ISO 11127-4:2020）

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:2020)

LST EN ISO 8501-4:2021 涂漆和相关产品前钢基材的准备 表面清洁度的目视评估 第4部分：与水喷射有关的初始表面条件、准备等级和闪锈等级（ISO 8501-4:2020）

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with water jetting (ISO 8501-4:2020)

BS EN ISO 8501-4:2020 涂料和相关产品使用前钢衬底的制备 表面清洁度的目测评估 与高压水冲法有关的初始表面条件、制备等级和闪锈等级

Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Initial surface conditions, preparation grades and flash rust grades in connection with water jetting

OENORM EN ISO 11127-4:2021 涂装油漆和相关产品前钢基材的制备 非金属喷砂清理磨料的试验方法 第4部分：通过载玻片试验评估硬度（ISO 11127-4:2020）

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:2020)

DIN/TR 55684:2021 通过防护涂料系统对钢结构进行腐蚀防护 在涂覆涂料材料之前对无法目视检测的容器进行表面测试

This document contains test to dedect oils, greases and waxes on for coating prepared steel surfaces.

Corrosion protection of steel structures by protective paint systems - Testing of surfaces before application of coating materials for containments that cannot be detected visually / Note: To be replaced by DIN/TR 55684 (2023-02).

ISO 3861:2021 喷砂和喷丸用橡胶软管和软管组件. 规范

This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.

Rubber hoses and hose assemblies for sand and grit blasting - Specification

SN EN ISO 8502-9:2021 涂漆和相关产品前钢基材的制备 表面清洁度评估试验 第9部分：水溶性盐类电导测定的现场方法（ISO 8502-9:2020）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:2020)

OENORM EN ISO 8502-9:2020 涂漆和相关产品前钢基材的制备 表面清洁度评估试验 第9部分：水溶性盐类电导测定的现场方法（ISO 8502-9:2020）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:2020)

UNI EN ISO 8502-9:2020 涂漆和相关产品前钢基材的准备 表面清洁度评估试验 第9部分：水溶性盐的电导测定的现场方法

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts

DIN EN ISO 8502-9:2020 应用涂料和相关产品前钢基体的制备. 表面清洁度评估试验. 第9部分: 水溶性盐电导测定的现场方法(ISO 8502-9-2020); 德文版 EN ISO 8502-9-2020

This document specifies a field method for the assessment of the surface density of various water-soluble salts on steel surfaces, before and/or after surface preparation, by conductometric determination. The individual surface densities of the salt composition like chlorides, su

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:2020); German version EN ISO

LST EN ISO 8502-9:2020 涂漆和相关产品前钢基材的制备 表面清洁度评估试验 第9部分：水溶性盐类电导测定的现场方法（ISO 8502-9:2020）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:2020)

KS B 4916-2020 喷丸

Shotblast

PN-EN ISO 8502-6-2020-11 E 涂装油漆和相关产品前钢基材的准备 表面清洁度评估试验 第6部分：提取水溶性污染物进行分析（Bresle 法）（ISO 8502-6:2020）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 6: Extraction of water soluble contaminants for analysis (Bresle method)(ISO 8502-6:2020)

DS/ISO 8501-4:2020 涂装油漆和相关产品前钢基材的准备 表面清洁度的目测评估 第4部分：与水射流相关的初始表面条件、准备等级和闪锈等级

Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with water jetting

DS/EN ISO 8501-4:2020 涂装油漆和相关产品前钢基材的预处理“表面清洁度的目测评估”第4部分：初始表面条件、预处理等级和与水喷射相关的闪锈等级（ISO 8501-4:2020）

Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with water jetting (ISO 8501-4:2020)

DS/EN ISO 11127-4:2020 涂装油漆和相关产品前钢基材的准备 非金属喷砂清理磨料的试验方法 第4部分：通过载玻片试验评估硬度（ISO 11127-4:2020）

Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:2020)

BS EN ISO 11127-4:2020 涂料和其它相关制品应用前钢基质的预处理. 非金属喷砂清理磨料试验方法. 用玻璃划痕试验评估硬度

Preparation of steel substrates before application of paints and related products. Test methods for non-metallic blast-cleaning abrasives. Assessment of hardness by a glass slide test

DS/ISO 11127-4:2020 涂装油漆和相关产品前钢基材的准备 非金属喷砂清理磨料的试验方法 第4部分：通过载玻片试验评估硬度

Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 4: Assessment of hardness by a glass slide test

ASTM B727-04(2020) 电镀塑料材料的制备标准实践

1.1 This practice is a guide to the surface preparation of plastic materials for decorative and functional electroplating, where the sequence of chemical treatments may include: cleaning, conditioning, etching, neutralizing, catalyzing, accelerating, and autocatalytic metal deposition. Surface preparation also includes electrodeposition of metallic strike coatings immediately after autocatalytic metal deposition. These treatments result in the deposition of thin conductive metal films on the surface of molded-plastic materials, and are described in this practice. 1.2 Once molded-plastics materials have been made conductive, they may be electroplated with a metal or combination of metals in conventional electroplating solutions. The electroplating solutions and their use are beyond the scope of this practice. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (See Section 4.) 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Plastics Materials for Electroplating