25.220.10 标准查询与下载

ASTM B727-04(2020) 电镀塑料材料的制备标准实践

1.1 This practice is a guide to the surface preparation of plastic materials for decorative and functional electroplating, where the sequence of chemical treatments may include: cleaning, conditioning, etching, neutralizing, catalyzing, accelerating, and autocatalytic metal deposition. Surface preparation also includes electrodeposition of metallic strike coatings immediately after autocatalytic metal deposition. These treatments result in the deposition of thin conductive metal films on the surface of molded-plastic materials, and are described in this practice. 1.2 Once molded-plastics materials have been made conductive, they may be electroplated with a metal or combination of metals in conventional electroplating solutions. The electroplating solutions and their use are beyond the scope of this practice. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (See Section 4.) 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Plastics Materials for Electroplating

SN EN ISO 8502-6:2020 涂漆和相关产品前钢基材的准备 表面清洁度评估试验 第6部分：提取水溶性污染物进行分析（Bresle 法）（ISO 8502-6:2020）

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 6: Extraction of water soluble contaminants for analysis (Bresle method) (ISO 8502-6:2020)

BS ISO 11127-8:2020 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料试验方法水溶性氯化物的现场测定

1   Scope This document specifies a field method for the determination of water-soluble chlorides in non-metallic blast-cleaning abrasives. This field method is provided as a kit with all components and premeasured extraction solution. This document differs from ISO 11127‑7 in that equal volumes of the sample of abrasive and extraction solution are used for the determination of chloride level in the abrasive. In comparison, ISO 11127‑7 uses a weight to volume ratio of abrasive to solvent (deionized water) to extract soluble salts from the abrasive. It is intended for use in the field as compared to ISO 11127‑7, which is well suited for use in the laboratory.

Preparation of steel substrates before application of paints and related products. Test methods for nonmetallic blast-cleaning abrasives - Field determination of water-soluble chlorides

NF T35-509-4:2020 涂料及相关产品应用前钢基体的预处理. 非金属喷砂清理磨料试验方法. 第4部分: 玻璃载片试验评估硬度(EN ISO 11127-4)

Le présent document spécifie une méthode pour déterminer si un abrasif non métallique destiné à la préparation par projection a une dureté minimale de 6 sur l'échelle de Mohs.Ce document fait partie de la série de normesISO 11127, qui traite de l'échantillonnage et des essais des

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4 : assessment of hardness by a glass slide test

EN ISO 11127-4:2020 使用涂料及相关产品前钢材的预处理.喷丸处理非金属磨料试验方法.第4部分:通过玻璃划痕试验评定硬度

This document specifies a method of assessing of whether a non-metallic blast-cleaning abrasive has a minimum hardness of 6 on Mohs' scale. This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. The ISO 11126 and ISO 11127 series have been drafted as a coherent set of International Standards on non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A. NOTE The test described in this document is a pass/fail test and is not a method for the accurate determination of hardness.

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:2020)

NF T35-501-4:2020 涂料和相关产品应用之前的钢材预处理. 表面清洁度的目视评估. 第4部分: 与水冲法有关的初始表面条件, 制备级别和闪锈级别

Domaine d'applicationLe présent document établit des principes généraux pour le choix de méthodes de préparation des subjectiles d'acier avant application de peintures et de produits assimilés. Il donne également des informations sur quelques particularités à prendre en compte av

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 4 : initial surface conditions, preparation grades and flash rust grades in connection with water jetting

EN ISO 8501-4:2020 涂料和相关产品使用前钢衬底的制备.表面清洁度的目视评定.第4部分:与水喷射有关的初始表面条件、制备等级和闪锈等级

This document specifies a series of preparation grades for steel surfaces after removal/partial removal of water-soluble contaminants, rust, previous paint coatings and other foreign matter by high-pressure water jetting. The various grades are defined by written descriptions together with photographs that are representative examples within the tolerances for each grade as described in words. This document specifies both initial surface conditions and after-cleaning flash rust grades, also defined by written descriptions together with representative photographic examples. This document applies the cleanliness of the surface to its visual appearance. Consideration in addition to visual appearance is given to invisible contaminants and roughness or profile. Physical and chemical methods for testing for soluble salts and other invisible contaminants on the visually clean surface are found in the ISO 8502 series. The roughness or profile characteristics of the surface are found in the ISO 8503 series.

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with water jetting (ISO 8501-4:2020)

DS/ISO 11124-5:2020 涂装油漆和相关产品前钢材表面的准备 金属喷砂清理磨料规范 第5部分：切割钢丝

Preparation of steel substrates before application of paints and related products – Specifications for metallic blast-cleaning abrasives – Part 5: Cut steel wire

ISO 8501-4:2020 涂料和相关产品使用前钢衬底的制备.表面清洁度的目视评定.第4部分:与水喷射有关的初始表面条件、制备等级和闪锈等级

This document specifies a series of preparation grades for steel surfaces after removal/partial removal of water-soluble contaminants, rust, previous paint coatings and other foreign matter by high-pressure water jetting. The various grades are defined by written descriptions together with photographs that are representative examples within the tolerances for each grade as described in words. This document specifies both initial surface conditions and after-cleaning flash rust grades, also defined by written descriptions together with representative photographic examples. This document applies the cleanliness of the surface to its visual appearance. Consideration in addition to visual appearance is given to invisible contaminants and roughness or profile. Physical and chemical methods for testing for soluble salts and other invisible contaminants on the visually clean surface are found in the ISO 8502 series. The roughness or profile characteristics of the surface are found in the ISO 8503 series.

Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 4: Initial surface conditions, preparation grades and flash rust gra

ISO 11127-8:2020 涂料和相关产品使用前钢衬底的制备.非金属喷砂清理磨料的试验方法.第8部分:水溶性氯化物的现场测定

This document specifies a field method for the determination of water-soluble chlorides in non-metallic blast-cleaning abrasives. This field method is provided as a kit with all components and premeasured extraction solution. This document differs from ISO 11127-7 in that equal volumes of the sample of abrasive and extraction solution are used for the determination of chloride level in the abrasive. In comparison, ISO 11127-7 uses a weight to volume ratio of abrasive to solvent (deionized water) to extract soluble salts from the abrasive. It is intended for use in the field as compared to ISO 11127-7, which is well suited for use in the laboratory.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 8: Field determination of water-soluble chlorides

ISO 11127-5:2020 涂料和相关产品应用前的钢基材的制备 - 非金属喷砂清洁磨料的测试方法 - 第5部分:水分测定

This document specifies a method for the determination of the level of free moisture present in non- metallic blast-cleaning abrasives. It is determined by measuring the mass lost on heating. This document is one of a number of parts of ISO 11127 dealing with the sampling and testing of non- metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. Standards on non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 5: Determination of moisture

ISO 11127-2:2020 涂料和相关产品应用前的钢基材的制备 - 非金属喷砂清洁磨料的测试方法 - 第2部分:粒度分布的测定

This document specifies a method for the determination of the particle size distribution of non-metallic blast-cleaning abrasives by sieving. This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements for each are contained in the ISO 11126 series. non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 2: Determination of particle size distribution

ISO 11127-1:2020 涂料和相关产品应用前的钢基材的制备 - 非金属喷砂清洁磨料的测试方法 - 第1部分:取样

This document specifies a method for the sampling of non-metallic blast-cleaning abrasives from consignments and for the subdivision of the sample into quantities suitable for undertaking the appropriate test methods specified in ISO 11127-2, ISO 11127-3, ISO 11127-4, ISO 11127-5, ISO 11127-6 This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements for each are contained in the ISO 11126 series. non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex B.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 1: Sampling

ISO 11127-3:2020 涂料和相关产品应用前的钢基材的制备 - 非金属喷砂清洁磨料的试验方法 - 第3部分:表观密度的测定

This document specifies a method for the determination of the apparent density of non-metallic blast- cleaning abrasives. This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements for each are contained in the ISO 11126 series. non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 3: Determination of apparent density

ISO 11127-4:2020 涂料和相关产品之前的钢基材料的制备 - 非金属喷砂清理剂的试验方法 - 第4部分:通过玻璃载片试验评估硬度

This document specifies a method of assessing of whether a non-metallic blast-cleaning abrasive has a minimum hardness of 6 on Mohs' scale. This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic abrasives for blast-cleaning. The types of non-metallic abrasive and requirements on each are contained in the ISO 11126 series. non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex A. NOTE The test described in this document is a pass/fail test and is not a method for the accurate determination of hardness.

Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 4: Assessment of hardness by a glass slide test

BS ISO 8502-15:2020 在涂覆油漆和相关产品之前准备钢基材 表面清洁度评估测试 通过酸萃取提取可溶性污染物进行分析

What is ISO 850215 about?    ISO 8502 discusses the preparation of steel substrates before the application of paints and related products. ISO 850215 is the fifteenth part of the ISO 8502 multi-series and discusses the extraction of soluble contaminants.    ISO 850215 specifies a method of extracting, for analysis, acid-soluble contaminants from a surface by use of flexible cells in the form of adhesive patches or sleeves which can be attached to any surface, regardless of its shape (flat or curved) and its orientation (facing in any direction, including downwards). ISO 850215 is similar in procedure to, but not equal to, ISO 85026 . The main difference is the solvent used and the subsequent analysis that can be performed on the extraction solution.   Note: ISO 850215 does not cover the subsequent analysis of the contaminants that have been dissolved off. Methods of analysis suitable for field use are described in other parts of ISO 8502 such as ISO 85025 .  Who is

Preparation of steel substrates before application of paints and related products. Tests for the assessment of surface cleanliness - Extraction of soluble contaminants for analysis by acid extraction

ISO 8502-15:2020 涂料和相关产品使用前钢衬底的制备.表面清洁度评定试验.第15部分:用酸萃取法分析可溶性污染物的萃取

This document specifies a method of extracting, for analysis, acid soluble contaminants from a surface by use of flexible cells in the form of adhesive patches or sleeves which can be attached to any surface, regardless of its shape (flat or curved) and its orientation (facing in any direction, including downwards). The described method is suitable for use in the field to determine the presence of acid soluble contaminants before painting or a similar treatment. This document does not cover the subsequent analysis of the contaminants that have been dissolved off. Methods of analysis suitable for field use are described in other parts of ISO 8502 such as ISO 8502-5. This document is similar in procedure to, but not equal to, ISO 8502-6. The main difference is the solvent used and the subsequent analysis that can be performed on the extraction solution.

Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 15: Extraction of soluble contaminants for analysis by acid e

EN ISO 8502-9:2020 涂装油漆和有关产品前钢材预处理表面清洁度的评定试验.第9部分:水溶性盐的现场电导测定法

This document specifies a field method for the assessment of the surface density of various water-soluble salts on steel surfaces, before and/or after surface preparation, by conductometric determination. The individual surface densities of the salt composition like chlorides, sulphates, sodium, etc, cannot be determined by this method. This method assesses only contaminants that forms an electrolyte (ions) when in contact with water. These represent the greater part of the contaminants.

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:2020)

ISO 8502-9:2020 涂料和相关产品前钢基材料的制备 - 表面清洁度评估试验 - 第9部分:水溶性盐电导率测定的现场方法

This document specifies a field method for the assessment of the surface density of various water-soluble salts on steel surfaces, before and/or after surface preparation, by conductometric determination. The individual surface densities of the salt composition like chlorides, sulphates, sodium, etc, cannot be determined by this method. This method assesses only contaminants that forms an electrolyte (ions) when in contact with water. These represent the greater part of the contaminants.

Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 9: Field method for the conductometric determination of water

BS EN ISO 8502-6:2020 在涂覆油漆和相关产品之前准备钢基材 表面清洁度评估测试 萃取水溶性污染物进行分析（布雷勒法）

What is ISO 8502 ‑ 6 about?    ISO 8502 discusses the preparation of steel substrates for paint application. ISO 8502 series covers tests for the assessment of surface cleanliness. ISO 8502 ‑ 6 specifies the Bresle method for extracting water-soluble contaminants from a surface, for analysis.   The Bresle method is suitable for use in the field to determine the presence of water-soluble contaminants before painting or a similar treatment.   Note1:  The extraction method might give a false negative or not take all the water-soluble material off the surface because of:   Soluble materials hiding in the crevices or under folds of metal  Soluble materials under corrosion layers, p...

Preparation of steel substrates before application of paints and related products. Tests for the assessment of surface cleanliness - Extraction of water soluble contaminants for analysis (Bresle method)