25.220.10 标准查询与下载

EN ISO 8502-6:2020 油漆和相关产品用前钢材的预处理.表面清洁度的评定试验.第6部分:提取分析用可溶性杂质.Bresle法

This document specifies a method of extracting, for analysis, water soluble contaminants from a surface by use of flexible cells in the form of adhesive patches or sleeves which can be attached to any surface, regardless of its shape (flat or curved) and its orientation (facing in any direction, including downwards). The method described is suitable for use in the field to determine the presence of water soluble contaminants before painting or a similar treatment. This document does not cover the subsequent analysis of the contaminants that have been dissolved. Methods of analysis suitable for field use are described in other parts of ISO 8502. NOTE The extraction method might give a false negative or not take all the water-soluble material off the surface because of: a) Soluble materials hiding in the crevices or under folds of metal; b) Soluble materials under corrosion layers, passivation layers produced by corrosion inhibitors, oil, grease, or other non-visible thin films.

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 6: Extraction of water soluble contaminants for analysis (Bresle method)(ISO 8502-6:2020)

ISO 8502-6:2020 涂料和相关产品使用前钢衬底的制备.表面清洁度评定试验.第6部分:分析用水溶性污染物的提取（布雷斯勒法）

This document specifies a method of extracting, for analysis, water soluble contaminants from a surface by use of flexible cells in the form of adhesive patches or sleeves which can be attached to any surface, regardless of its shape (flat or curved) and its orientation (facing in any direction, including downwards). The method described is suitable for use in the field to determine the presence of water soluble contaminants before painting or a similar treatment. This document does not cover the subsequent analysis of the contaminants that have been dissolved. Methods of analysis suitable for field use are described in other parts of ISO 8502. NOTE The extraction method might give a false negative or not take all the water-soluble material off the surface because of: a) Soluble materials hiding in the crevices or under folds of metal; b) Soluble materials under corrosion layers, passivation layers produced by corrosion inhibitors, oil, grease, or other non-visible thin films.

Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 6: Extraction of water soluble contaminants for analysis (Bre

ASTM D4940-15(2020) 用于喷砂清理磨料水溶解离子污染导电分析的标准测试方法

1.1 This test method describes a procedure for assessing blast cleaning abrasives for the presence of conductivepotential, ionic contaminants by determining the total concentration of water soluble conductive species using a conductivity test. 1.2 This test method does not identify the ionic species present nor provide quantitative results on each species. 1.3 This test method is based on a volume comparison among abrasives of similar sizes. A volume comparison is more closely related to surface area of the abrasives than is a weight comparison. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives

ASTM D4376-15(2020) 蒸汽脱脂级全氯乙烯的标准规格

1.1 This specification covers vapor-degreasing grade perchloroethylene.2 NOTE 1—Guide D3844 and Practice D4276 provide additional important information on solvent properties. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Vapor-Degreasing Grade Perchloroethylene

BS EN ISO 8504-2:2019 在涂覆油漆和相关产品之前准备钢基材 表面处理方法 喷砂清理

What is ISO 8504 ‑ 2 - Preparation of steel substrates before application of paints about?    ISO 8504 ‑ 2 is part two of a multi-series of international standards on preparation of steel substrates before application of paints and related products which covers the abrasive blast-cleaning method.   ISO 8504 ‑ 2  specifies abrasive blast-cleaning methods for the preparation of steel surfaces before   coating with paints and related products.

Preparation of steel substrates before application of paints and related products. Surface preparation methods - Abrasive blast-cleaning

BS EN ISO 8504-1:2019 在涂覆油漆和相关产品之前准备钢基材 表面处理方法 一般原则

What is ISO 8504 ‑ 1 - Preparation of steel substrates before application of paints about?    ISO 8504 ‑ 1 is part one of a multi-series of international standards on preparation of steel substrates before application of paints and related products which covers its general principles.   ISO 8504 ‑ 1 describes the general principles for the selection of methods for the preparation of steel surfaces before application of paints and related products.   

Preparation of steel substrates before application of paints and related products. Surface preparation methods - General principles

KS M ISO 12944-4:2019 色漆和清漆防护涂料体系对钢结构的腐蚀防护第4部分:表面类型和表面处理

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 4：Types of surface and surface preparation

KS M ISO 12944-4-2019 色漆和清漆防护涂料体系对钢结构的腐蚀防护第4部分:表面类型和表面处理

Paints and varnishes－Corrosion protection of steel structures by protective paint systems－Part 4：Types of surface and surface preparation

KS M ISO 11124-4:2019 涂料和相关产品应用前的钢基材的制备 - 金属喷砂清理磨料规范 - 第4部分:低碳铸钢射击

Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot

KS M ISO 8501-2-2019 应用涂料和相关产品前的钢基材料的制备 - 表面清洁度的目视评估 - 第2部分:局部除去以前的涂层之后的预先涂覆的钢基材的制备等级

Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 2: Preparation grades of previously coated steel substrates after lo

KS M ISO 8501-2:2019 应用涂料和相关产品前的钢基材料的制备 - 表面清洁度的目视评估 - 第2部分:局部除去以前的涂层之后的预先涂覆的钢基材的制备等级

Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 2: Preparation grades of previously coated steel substrates after lo

KS M ISO 11124-3-2019 涂料和相关产品应用前的钢基材的制备 - 金属喷砂清理磨料规范 - 第3部分:高碳铸钢球磨机

Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit

KS M ISO 11124-3:2019 涂料和相关产品应用前的钢基材的制备 - 金属喷砂清理磨料规范 - 第3部分:高碳铸钢球磨机

Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit

KS M ISO 11124-4-2019 涂料和相关产品应用前的钢基材的制备 - 金属喷砂清理磨料规范 - 第4部分:低碳铸钢射击

Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot

KS M ISO 8501-3-2019 涂装油漆及相关产品前钢基材的制备 表面清洁度的目视评估 第3部分：焊缝、切割边缘和其他有表面缺陷区域的制备等级

Preparation of steel substrates before application of paints and related products－Visual assessment of surface cleanliness－Part 3：Preparation grades of welds,cut edges and other areas with surface imperfections

EN ISO 8504-2:2019 涂装油漆和有关产品前钢材预处理.表面预处理方法.第2部分:磨料喷射清理

This document specifies abrasive blast-cleaning methods for the preparation of steel surfaces before coating with paints and related products. It provides information on the effectiveness of the individual methods and their fields of application. It describes the equipment to use and the procedure to follow. NOTE These methods are essentially intended for hot-rolled steel to remove mill scale, rust, etc. but could also be used for cold-rolled steel of sufficient thickness to withstand the deformation caused by the impact of abrasive.

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 2: Abrasive blast-cleaning (ISO 8504-2:2019)

EN ISO 8504-1:2019 涂装油漆和有关产品前钢材预处理表面预处理方法.第1部分:总则

This document describes the general principles for the selection of methods for the preparation of steel surfaces before application of paints and related products. It also contains information on features that are taken into account when selecting and specifying certain surface preparation methods and preparation grades.

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 1: General principles (ISO 8504-1:2019)

ISO 8504-2:2019 涂料和相关产品之前制备钢基材 - 表面处理方法 - 第2部分:磨料喷砂清洗

This document specifies abrasive blast-cleaning methods for the preparation of steel surfaces before coating with paints and related products. It provides information on the effectiveness of the individual methods and their fields of application. It describes the equipment to use and the procedure to follow. NOTE These methods are essentially intended for hot-rolled steel to remove mill scale, rust, etc. but could also be used for cold-rolled steel of sufficient thickness to withstand the deformation caused by the impact of abrasive.

Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning

ISO 8504-1:2019 油漆及相关产品应用前钢基材料的制备 - 表面处理方法 - 第1部分:一般原则

This document describes the general principles for the selection of methods for the preparation of steel surfaces before application of paints and related products. It also contains information on features that are taken into account when selecting and specifying certain surface preparation methods and preparation grades.

Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 1: General principles

ASTM F3401-19 马术合成跑道表面蜡粘合剂去除的标准试验方法

1.1 Equine surfaces containing wax-oil based coatings/ binders must be treated and cleaned prior to the subsequent material tests described for sand and fiber surfaces. Note: skip this test for surfaces that are not wax coated. 1.2 The procedures described for wax separation employ Soxhlet extraction to remove wax content from the surface and to calculate crude wax percentage in the surface. Procedures are based upon the Soxhlet extraction method, which has been modified for use on equestrian surfaces by Lab/Cor Materials, Seattle, Washington, USA.2 1.3 If synthetic fibers are present, then fiber solubility will need to be considered prior to Soxhlet extraction to ensure that the Soxhlet procedure will not damage fiber integrity. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wax Binder Removal from Equestrian Synthetic Track Surfaces