25.220.10 标准查询与下载

ISO/TR 22770:2019 涂料和相关产品使用前钢衬底的制备.支持表面制备等级目视评估的分析比色法

Preparation of steel substrates before application of paints and related products — Analytical colorimetry method to support visual assessment of surface preparation grades

ASTM E1793-19 泡沫和梁式运输庇护所中用于粘合的铝合金的标准实践

1.1 This practice covers the preparation of clean, uniform surfaces of aluminum alloy suitable for formation of durable adhesive bonds in “foam and beam” panels used for the manufacture of tactical rigid wall shelters. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Aluminum Alloy for Bonding in Foam and Beam Type Transportable Shelters

ISO 11124-5:2019 涂料和相关产品使用前钢衬底的制备.金属喷砂清理磨料规范.第5部分:切割钢丝（ISO 11124-5-2019）

This document specifies requirements for 13 grades of cut steel wire abrasives, as supplied for blast- cleaning processes. It specifies ranges of particle sizes, together with corresponding grade designations. Values are specified for hardness, density, defect/structural requirements, metallographic structure and chemical composition. This document is suitable for cut steel wire supplied for blast-cleaning processes which is made by cutting new cold drawn wire. The requirements specified in this document apply to abrasives manufactured from virgin wire supplied in the new and unconditioned state only. They do not apply to abrasives either during or after use. NOTE 1 Information on commonly referenced national standards for cut steel wire abrasives and their approximate relationship with ISO 11124 is given in Annex A. NOTE 2 Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques.

Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 5: Cut steel wire

ASTM B281-88(2019)e1 电镀和转化涂层用铜和铜基合金的制备

1.1 This practice is intended to serve as a guide for the proper preparation of copper and its alloys for electroplating and conversion coating. This practice is also suitable for use before autocatalytic plating. Only alloys containing at least 50 mass % copper are considered within the scope of this practice. 1.2 The wide variety of methods of mechanical finishing are not considered strictly as preparation for electroplating or conversion coating and consequently are described only briefly. 1.3 Details of electroplating and subsequent treatments for applying conversion coatings are not within the scope of this practice. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 6.5.2. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Copper and Copper-Base Alloys for Electroplating and Conversion Coatings

BS EN ISO 8504-3:2018 在涂覆油漆和相关产品之前准备钢基材 表面处理方法 手动和电动工具清洁

What is ISO 8504‑3 about? ISO 8504 discusses the preparation of steel substrates before the application of paints and related products. ISO 8504‑3 is the third part of the ISO 8504 multi-series and discusses surface preparation methods. The primary objective of surface preparation is to ensure the removal of deleterious matter and to obtain a surface that permits satisfactory adhesion of the priming paint to the steel. It also assists in reducing the amounts of contaminants that initiate corrosion. ISO 8504‑3 describes methods for hand- and power-tool cleaning. It should be read in conjunction with ISO 8504‑1 . Who is ISO 8504‑3 for ? ISO 8504‑3 on the preparation of steel substrates before application of paints and related products (hand- and power-tool cleaning) is useful for: Manufacturers of steel products Quality control personnel Painters Why should you use ISO 8504‑3? The performance of protective coatings of paint and related products applied to steel is significantly affected by the state of the steel surface immediately prior to painting.

Preparation of steel substrates before application of paints and related products. Surface preparation methods. Hand- and power-tool cleaning

KS M ISO 11126-10-2018 涂料和有关产品使用前钢衬底的制备.非金属喷砂清理磨料规范.第10部分:铝榴石-石榴石

Preparation of steel substrates before application of paints and related products — Specification for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet

KS M ISO 8503-5:2018 涂料和相关产品应用前的钢基材的制备 - 喷砂清理钢基材的表面粗糙度特性 - 第5部分:表面轮廓测定的复制带方法

Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determinat

KS M ISO 11126-10:2018 涂料和有关产品使用前钢衬底的制备.非金属喷砂清理磨料规范.第10部分:铝榴石-石榴石

Preparation of steel substrates before application of paints and related products — Specification for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet

KS M ISO 8503-5-2018 涂料和相关产品应用前的钢基材的制备 - 喷砂清理钢基材的表面粗糙度特性 - 第5部分:表面轮廓测定的复制带方法

Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determinat

EN ISO 8504-3:2018 涂装油漆和有关产品前钢材预处理.表面预处理方法.第3部分:手工和动力工具清洗

This document describes methods for hand-tool and power-tool cleaning of steel substrates before application of paints and related products. It is applicable both to new steelwork and to steel surfaces that have been coated previously and that show areas of breakdown requiring maintenance painting. It describes the equipment to be used and the procedures to be followed.

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 3: Hand- and power-tool cleaning (ISO 8504-3:2018)

BS EN ISO 11125-1:2018 在涂覆油漆和相关产品之前准备钢基材 金属喷砂清理磨料的测试方法 采样

What is ISO 11125-1 - Metallic blast-cleaning abrasives about?    ISO 11125 discusses test methods for metallic blast-cleaning abrasives.   ISO 11125-1 is the first part of ISO 11125 multi-series and discusses sampling. ISO 11125-1 deals with the sampling and testing of metallic abrasives for blast cleaning.   The types of metallic abrasive and requirements for each are contained in the various parts of ISO 11124 . The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives.   Who is ISO 11125-1 -

Preparation of steel substrates before application of paints and related products. Test methods for metallic blast-cleaning abrasives. Sampling

BS EN ISO 11125-7:2018 在涂覆油漆和相关产品之前准备钢基材 金属喷砂清理磨料的测试方法 水分测定

What is ISO 11125-7 - Metallic blast-cleaning abrasives about?    ISO 11125 discusses test methods for metallic blast-cleaning abrasives. ISO 11125-7 is the seventh part of ISO 11125 and discusses the determination of moisture and dealing with the sampling and testing of metallic abrasives for blast cleaning.    The types of metallic abrasive and requirements for each are contained in the various parts of ISO 11124. The ISO 11124 and ISO 11125 series have been drafted as a coherent set of International Standards on metallic blast-cleaning abrasives.   Who is ISO 11125-7 - Metallic blast-cleaning abrasives for?   ISO 11125-7 on ...

Preparation of steel substrates before application of paints and related products. Test methods for metallic blast-cleaning abrasives. Determination of moisture

ISO 8504-3:2018 涂料和相关产品应用前的钢基材的制备 - 表面处理方法 - 第3部分:手动和电动工具清洁

This document describes methods for hand-tool and power-tool cleaning of steel substrates before application of paints and related products. It is applicable both to new steelwork and to steel surfaces that have been coated previously and that show areas of breakdown requiring maintenance painting. It describes the equipment to be used and the procedures to be followed.

Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 3: Hand- and power-tool cleaning

BS EN ISO 11126-7:2018 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料规范 电熔氧化铝

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Fused aluminium oxide

BS EN ISO 11124-3:2018 在涂覆油漆和相关产品之前准备钢基材 金属喷砂清理磨料的规范 高碳铸钢丸和砂粒

Preparation of steel substrates before application of paints and related products. Specifications for metallic blast-cleaning abrasives. High-carbon cast-steel shot and grit

BS EN ISO 11126-5:2018 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料规范 镍渣

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Nickel slag

BS EN ISO 11126-6:2018 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料规范 钢铁渣

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Iron and steel slags

BS EN ISO 11126-8:2018 涂料和其它相关制品应用前钢基质的预处理. 喷非金属清理磨料规格. 橄榄石砂

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Olivine

BS EN ISO 11126-1:2018 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料规范 总体介绍及分类

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. General introduction and classification

BS EN ISO 11126-4:2018 在涂覆油漆和相关产品之前准备钢基材 非金属喷砂清理磨料规范 煤炉渣

Preparation of steel substrates before application of paints and related products. Specifications for non-metallic blast-cleaning abrasives. Coal furnace slag