25.220.20 标准查询与下载

BS EN 17002:2018 热喷涂 具有热喷涂涂层的部件 热喷涂程序规范

Thermal spraying. Components with thermally sprayed coatings. Thermal spray procedure specification

EN 17001:2018 热喷涂 带热喷涂涂层的部件 涂层规范

Thermal spraying - Components with thermally sprayed coatings - Coating specification

EN 17002:2018 热喷涂 具有热喷涂涂层的部件 热喷涂程序规范

Thermal spraying - Components with thermally sprayed coatings - Thermal spray procedure specification

EN 1395-5:2018 热喷涂.热喷涂设备的验收检验.第5部分:室内等离子喷涂

Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 5: Plasma spraying in chambers

ISO 2085:2018 铝和铝合金的阳极氧化 阳极氧化膜的连续性检验 硫酸铜试验

This document specifies a method for checking the continuity of thin anodic oxidation coatings on aluminium and its alloys by a copper sulfate contact test. The use of this method is limited to anodic oxidation coatings of thickness less than 5 µm or coatings that have been deformed, which includes those produced by coil anodizing techniques. NOTE The method described enables a rapid check to be made for the continuity of a thin coating of aluminium oxidation on aluminium and its alloys. In cases of doubt regarding a visible fault on the surface of a coating, the use of this method makes it possible to verify whether the fault corresponds to a local gap in the coating that exposes bare metal.

Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test

ISO 6581:2018 铝和铝合金的阳极氧化 着色阳极氧化膜耐紫外光的测定

This document specifies a comparative method for the determination of the fastness of coloured anodic oxidation coatings to ultraviolet (UV) light and heat. The method is not suitable for testing coloured anodic oxidation coatings that are heat sensitive. NOTE Dark-coloured test specimens will normally reach the highest temperatures.

Anodizing of aluminium and its alloys - Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings

ISO 8251:2018 铝和铝合金的阳极氧化.阳极氧化涂层耐磨性测量

This document specifies the following tests: a) abrasive-wheel-wear test, determining the abrasion resistance of anodic oxidation coatings with abrasive wheel on flat specimens of aluminium and its alloys; c) falling sand abrasion test, determining the abrasion resistance of anodic oxidation coatings with falling sand on thin anodic oxidation coatings of aluminium and its alloys. b) abrasive jet test, determining the comparative abrasion resistance of anodic oxidation coatings with jet of abrasive particles on anodic oxidation coatings of aluminium and its alloys; The use of abrasive-wheel-wear test and abrasive jet test for coatings produced by hard anodizing is described in ISO 10074.

Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings

BS EN 17059:2018 电镀和阳极氧化线 安全要求

What is BS EN 17059- Plating and anodizing lines about?    BS EN 17059 describes all significant hazards, hazardous situations and events relating to plating and anodizing lines, when used as intended and in compliance with the foreseeable conditions of the manufacturer.    BS EN 17059 applies to the design and construction of plating lines and anodizing lines including their transporter systems for surface treatment of industrial products by means of inorganic or organic electrolytes or by means of other processes chemistries.   Plating lines and anodizing lines in terms of this standard are arrangements of process tanks for:  

Plating and anodizing lines. Safety requirements

BS EN ISO 14918:2018 热喷涂 热喷涂机的鉴定测试

Thermal spraying. Qualification testing of thermal sprayers

EN ISO 14918:2018 热喷涂.热喷涂器的验收试验

Thermal spraying - Qualification testing of thermal sprayers

ASTM D1978-91(2018) 分析电泳浴样品的标准指南

1.1 This guide covers the selection of test methods for determination of the important parameters that affect the performance of electrocoating paints. 1.2 The test methods involved are D4370, D4399, D4584, and D5145. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Analysis of Electrocoat Bath Samples

EN 17059:2018 电镀和阳极氧化生产线 安全要求

Plating and anodizing lines - Safety requirements

DB34/T 3086-2018 钢板涂层中六价铬含量的测定 分光光度法

本标准规定了分光光度法测定钢板涂层中六价铬含量。 本标准适用于钢板表面用化学或者电化学方法产生的涂层中六价铬含量的测定。 本标准测量范围 0.05 μg/cm2～10.00 μg/cm2。

Determination of hexavalent chromium content in steel plate coating spectrophotometric method

CSA G164-2018 不规则形状物品的热浸镀锌

1 Scope 1.1 This Standard specifies the requirements for zinc coating (galvanizing) by the hot-dipping process on iron and steel products intended or primarily for use in electrical and communication systems, made from rolled, pressed, cast iron, or forged shapes such as structural sections, plates, bars, pipes, or sheets 1 mm thick and thicker. 1.2 This Standard applies to a) both unfabricated and fabricated products such as assembled steel products, structural steel fabrications, large hollow sections bent or welded before galvanizing, and wire work fabricated from uncoated steel wire; and b) steel forgings and iron castings that are to be galvanized separately or in batches. 1.3 This Standard does not apply to a) the continuous galvanizing of chain link fence fabric, wire, sheet, and strip; and b) pipe and conduit that are normally hot dip galvanized by a continuous or semicontinuous automatic process. 1.4 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Hot dip galvanizing of irregularly shaped articles

ISO 14918:2018 热喷涂.热喷涂人员的合格测试

This document specifies procedural instructions for qualification testing of thermal sprayers. It defines requirements, ranges of qualification, test conditions, acceptance requirements and certification for qualification testing of thermal spray performance. This document is applicable when the thermal sprayer’s qualification is required by this document, the purchaser, by inspection authorities or by other organizations. The thermal spraying processes referred to in this document include those spraying processes which are designated as manual or mechanized. The test for mechanised application includes the use of automatically controlled thermal spraying, e.g. robotics, scan units.

Thermal spraying - Qualification testing of thermal sprayers

BS EN ISO 17836:2017 热喷涂 热喷涂沉积效率的测定

Thermal spraying. Determination of the deposition efficiency for thermal spraying

DIN EN ISO 17836:2018 热喷涂.热喷涂熔敷效率的测定(ISO 17836-2017);德文版本EN ISO 17836-2017

This standard defines the procedure for determining the deposition efficiency for a thermal spray process in connection with a spray material and related equipment and auxiliary materials. It is applicable for all thermal spray processes (see ISO 14917) and all wire, rod, cord and powder spray materials. This standard shall be applied if data concerning the deposition efficiency of a spray process in connection with a defined spray material are required.

Thermal spraying - Determination of the deposition efficiency for thermal spraying (ISO 17836:2017); German version EN ISO 17836:2017

BS EN ISO 7599:2018 铝及其合金的阳极氧化. 铝表面装饰性和保护性阳极氧化膜的确定方法

Anodizing of aluminium and its alloys. Method for specifying decorative and protective anodic oxidation coatings on aluminium

BS EN ISO 2931:2018 铝及其合金的阳极氧化 通过导纳测量评估密封阳极氧化涂层的质量

Anodizing of aluminium and its alloys. Assessment of quality of sealed anodic oxidation coatings by measurement of admittance

EN ISO 7599:2018 铝和铝合金的阳极氧化.铝阳极氧化膜的一般规范

Anodizing of aluminium and its alloys - Method for specifying decorative and protective anodic oxidation coatings on aluminium