29.035.60 涂层织物 标准查询与下载

ASTM D3056-14 无溶剂清漆凝固时间的标准试验方法

4.1 Gel time is important in determining batch uniformity and some processing characteristics. It is indicative of pot life and shelf life. 1.1 This test method covers the determination of the gel time of a solventless varnish mixed with a catalyst, if required, and exposed to elevated temperature. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see Section 6. Note 1: Although this standard and IEC 60455–2 differ in approach or detail, data obtained using either are technically equivalent.

Standard Test Method for Gel Time of Solventless Varnishes

GSO IEC 60394-2:2013 电气用抛光器具 第2部分：测试方法

Abstract Describes methods of test to determine the electrical, mechanical and chemical resistance of varnished fabrics and includes descriptions of the testing apparatus to be employed,

Varnished fabrics for electrical purposes. Part 2: Methods of test

ANSI/ASTM D3145:2013 用螺旋线圈法对电绝缘清漆耐热性的试验方法

Test Method for Thermal Endurance of Electrical Insulating Varnishes by the Helical Coil Method

ANSI/ASTM D1932:2013 柔性电绝缘漆耐热性试验方法

TEST METHOD FOR THERMAL ENDURANCE OF FLEXIBLE ELECTRICAL INSULATING VARNISHES

ANSI/ASTM D3955:2013 电绝缘漆规格

SPECIFICATION FOR ELECTRICAL INSULATING VARNISHES

ANSI/ASTM D4733:2013 无溶剂电绝缘清漆的试验方法

TEST METHODS FOR SOLVENTLESS ELECTRICAL INSULATING VARNISHES

ASTM D3056-05(2010) 无溶剂清漆凝胶时间的标准测试方法

Standard Test Method for Gel Time of Solventless Varnishes

ASTM D4880-08 绝缘漆的盐水防腐标准测试方法

This test method is useful in determining the performance of varnishes over enamelled magnet wire when subjected to the specified sodium chloride solution. It is useful in evaluating the resistance of varnished magnet wire to a diluted sodium chloride solution under applied voltage.1.1 This test method covers the performance in a specified water solution of an insulating varnish applied over enamelled magnet wire. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6. Note 18212;There is no IEC method equivalent to this standard.

Standard Test Method for Salt Water Proofness of Insulating Varnishes Over Enamelled Magnet Wire

ASTM D411-08 电绝缘用紫胶片的标准试验方法

Polymerization time provides a measure of time during which shellac retains its plasticity and flow properties at the specified temperature before gelling or polymerizing to the tough rubbery insoluble form. This test is important in determining the quality of different lots, useful shelf-life, batch uniformity, and processing characteristics of shellac. 1.1 These test methods cover tests for shellac in the dry button or powder form to be used for electrical insulating purposes. Typically, shellac is used as a bonding agent for mica splittings and reconstituted mica paper products, or as a coating or adhesive for other material. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no similar or equivalent IEC standard. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Test Methods for Shellac Used for Electrical Insulation

ANSI/ASTM D4880:2008 绝缘清漆涂覆的磁线的盐水试验用试验方法

Test Method for Salt Water Proofness of Insulating Varnishes over Enameled Magnet Wire

ANSI/ASTM D6053:2008 高度绝缘清漆的挥发性有机化合物(VOC)含量的测定用试验方法

Test Method for Determination of Volatile Organic Compound (VOC) Content of Electric Insulating Varnishes

ANSI/ASTM D411:2008 电绝缘用虫胶漆的试验方法

Test Methods for Shellac used for Electrical Insulation

ANSI/ASTM D784:2008 电气绝缘用柑桔虫胶和其他印度紫胶用规范

Specification for Orange Shellac and Other Indian Lacs for Electrical Insulation

ASTM D784-08 电绝缘材料用橙色紫胶和其他印度虫胶标准规范

1.1 This specification covers the requirements and methods of test for three types and four grades of orange shellac and other lacs, typically used as bonding agents for mica splittings and reconstituted mica paper and as coating for other materials, as follows: 1.1.1 Type I8212;Orange Flake Shellac, Grades A, B, C, and D, 1.1.2 Type II8212;Button Lac, and 1.1.3 Type III8212;Garnet Lac. 1.2 Stick-lac and seed-lac are not covered by this specification. Note 18212;ISO Specifications 56–1 and 56–2 cover shellac. However, the equivalency of the ISO specification to this standard is unknown. Refer directly to the ISO standards to determine equivalency. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

Standard Specification for Orange Shellac and Other Indian Lacs for Electrical Insulation

DIN EN 61033:2007 浸渍剂对漆包线衬底粘结强度测定的试验方法

Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate (IEC 61033:1991 + A1:2006); German version EN 61033:2006

DS/EN 61033:2007 测定浸渍剂对漆包线基材粘合强度的试验方法

This standard describes three methods of test to determine the bond strength of impregnating agents such as solvent-based varnishes and solventless resins to an enamelled wire substrate. Bond strength may be affected by cure, by test temperature, by thermal ageing, and for any impregnating agent, by the chosen type of wire enamel.These three methods of test cover the prevailing standard practice of testing bond strength. For a certain group of materials, one of these methods may be assigned to be the referee method subject to a specification in the relevant specification sheet.

Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate

ANSI/ASTM D115:2007 电绝缘用含清漆测试溶剂的试验方法

These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods include tests for control and performance as follows:Where the entire test method is included in this standard, the precision and bias are not known unless given in the stated method. The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5. Note 1There is no equivalent IEC standard.

Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation

ANSI/ASTM D2756:2007 电绝缘清漆的重量损失用试验方法

This test method covers the measurement of the loss in weight of cured electrical insulating varnishes on exposure to elevated temperature in air. The values stated in SI units are the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precaution statements, see Section 7. Note 1IEC 60216 Part 2 is technically equivalent to this standard.

Test Method for Weight Loss of Electrical Insulating Varnishes

ANSI/ASTM D2519:2007 用螺旋线圈试验测定电绝缘清漆粘结强度的试验方法

This test method covers determination of the bond strength of an electrical insulating varnish when applied to a helical coil. The helical coil can be made from bare aluminum or copper wire or from film or fiber-insulated magnet wire. Helical coils made from bare aluminum or bare copper wire will yield values of bond strength for the varnish when applied to bare metal conductors. The use of film or fiber-insulated magnet wire will show values for that particular combination of insulation and varnish. The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 7.

Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test

DS/EN 60464-3-2/A1:2007 电绝缘用清漆 第3部分：个别材料规范 第 2 页：热固化浸渍清漆

This sheet specifies requirements for hot curing impregnating varnishes and includes requirements for certain properties at elevated temperatures.

Varnishes used for electrical insulation - Part 3: Specifications for individual materials - Sheet 2: Hot curing impregnating varnishes