29.035.60 涂层织物 标准查询与下载

DS/EN 60464-2:2002 电绝缘用清漆 第2部分：测试方法

This part of 60464 specifies methods of test to be used for testing varnishes used for electrical insulation. This includes methods of test to be applied before and others to be applied after drying and/or curing of the varnish.

Varnishes used for electrical insulation - Part 2: Methods of Test

BS EN 60464-3-2:2002 用于电气绝缘的清漆

This sheet of IEC 60464-3 gives the requirements for hot curing impregnating varnishes and includes requirements for certain properties at elevated temperature.

Varnishes used for electrical insulation

BS EN 60464-3-1:2002 用于电气绝缘的清漆 个别材料的规格 表 1：常温固化面漆

This sheet of IEC 60464-3 gives the requirements for ambient curing finishing varnishes.

Varnishes used for electrical insulation. Specifications for individual materials. Sheet 1: Ambient curing finishing varnishes

KS C IEC 60394-3-2:2001 电工用浸漆织物.第3部分:单项材料规范.第2节:用环氧树脂、聚氨基甲酸乙酯、有机硅树脂、聚酯、沥青或油性树脂清漆浸渍的玻璃纤维基织物

규격의 이 절에서는 다음 수지의 바니시 처리한 유리 직물에 대한 요구 사항에 대해 규정한다

Varnished fabrics for electrical purposes－Part 3：Specifications for individual materials－Sheets 2：Glass－fabric based varnished fabrics with epoxy, polyurethane, silicone, polyester, bituminous or oleoresinous varnish

KS C IEC 60394-3-1:2001 电工用浸漆织物.第3部分:单项材料规范.第1节:油性树脂漆浸渍棉织物

서 론 이 규격은 전폭 롤, 판 또는 다양한 나비로 절단된 테이프 형태로 공급되는 면,

Varnished fabrics for electrical purposes-Part 3:Specifications for individual materials-Sheet 1:Oleoresinous varnish-cotton base, OR/C

KS C IEC 60394-1:2001 电工用浸漆织物.第1部分:定义和通用要求

이 규격에서는 전기용 바니시 처리된 직물류와 관계된 정의와 일반 요구 사항을 포함한다.

Varnished fabrics for electrical purposes－Part 1：Definitions and general requirements

BS EN 60464-2:2001 用于电气绝缘的清漆 测试方法

Varnishes used for electrical insulation. Methods of test

ASTM D1932-97 挠性电绝缘清漆耐热性的标准试验方法

1.1 This test method covers the determination of the relative thermal endurance of flexible electrical insulating varnishes by determining the aging time necessary at elevated temperatures to decrease the dielectric breakdown of the varnish to an arbitrarily selected value when applied to a standard glass fiber fabric.1.2 This test method does not apply to varnishes that lose a high percentage of their dielectric breakdown voltage when flexed before aging as prescribed in the screening test (Section 9). Examples of such varnishes are those used for high speed armatures and laminated structures. Also, this test method is not applicable to varnishes which distort sufficiently during thermal aging so that they cannot be tested using the curved electrode assembly.1.3 Thermal endurance is expressed in terms of a temperature index.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 1.5 The values stated in SI units are the standard.Note 1--There is no equivalent IEC or ISO standard.

Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes

ASTM D4882-97 用扭曲线圈试验测定电绝缘清漆粘结强度的标准试验方法

1.1 This test method covers the determination of the bond strength of an electrical insulating varnish when applied to a twisted coil of film-insulated magnet wire. The use of a particular type of film-insulated wire will show the values for that combination of film coating and varnish. 1.2 This standard does not purport to address all, if any, of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Section 7. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. Note 18212;Although this standard and Method C of IEC 61033 differ in approach or detail, data obtained using either are technically equivalent.

Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test

IEC 60464-3-1:2001 电气绝缘漆 第3部分：单项材料规范 活页1：环境固化覆盖漆

This sheet of IEC 60464-3 gives the requirements for ambient curing finishing varnishes.

Varnishes used for electrical insulation - Part 3: Specifications for individual materials; Sheet 1: Ambient curing finishing varnishes

IEC 60464-2:2001 电气绝缘漆 第2部分：试验方法

This part of IEC 60464 specifies methods of test to be used for testing varnishes used for electrical insulation. This includes methods of test to be applied before and others to be applied after drying and/or curing of the varnish.

Varnishes used for electrical insulation - Part 2: Methods of test

IEC 60464-3-2:2001 电气绝缘漆 第3部分：单项材料规范 活页2：热固化浸渍漆

This sheet of IEC 60464-3 gives the requirements for hot curing impregnating varnishes and includes requirements for certain properties at elevated temperature.

Varnishes used for electrical insulation - Part 3: Specifications for individual materials; Sheet 2: Hot curing impregnating varnishes

ANSI/ASTM D3377:2000 无溶剂清漆重量损失试验方法

This test method covers the determination of the percent weight loss of cured solventless electrical varnishes when exposed to elevated temperatures for prescribed periods of time. Results of this test method are based on 6-mm (1/4-in.) thick specimens and will not be applicable to specimens appreciably thinner or thicker than 6 mm. The values stated in SI units are to be regarded as the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1 -This standard resembles IEC 60216-2 "Guide for the determination of thermal endurance properties of electrical insulating materials. Part 2: Choice of test criteria" in a number of ways, but is not consistently similar throughout. The data obtained using either standard will possibly be technically equivalent.

Test Method for Weight Loss of Solventless Varnishes

DS/EN 60464-1:1999 电绝缘用清漆 第1部分：定义和一般要求

This part of IEC 60464 relates to varnishes used for electrical insulation. All varnishes contain solvent. The varnishes may be used for finishing impregnating applications, and may be dried or dried and cured at ambient or elevated temperatures.

Varnishes used for electrical insulation - Part 1: Definitions and general requirements

JIS C 2103:1999 电绝缘清漆的检验方法

Testing methods of varnishes for electrical insulation

JIS C 2120:1999 电绝缘用漆布和带的检验方法

この規格は，ワニスクロス類の試験方法について規定する。なお，この規格の項目のうち，A法及びB法の二つの内容が規定されていろ項日は，一つの製品に対してそのA法又はB法のいずれかを併記された項目すべてについて一貫して適用するものとし，項目によってそのいずれかを適宜選択又は混用して適用することはできない。

Testing method of varnished cloths and tapes for electrical insulation

ASTM D784-99 电气绝缘用橙色虫胶和其他印度紫胶的标准规范

1.1 This specification covers the requirements and methods of test for three types and four grades of orange shellac and other lacs, typically used as bonding agents for mica splittings and reconstituted mica paper and as coating for other materials, as follows: 1.1.1 Type I -Orange Flake Shellac, Grades A, B, C, and D, 1.1.2 Type II -Button Lac, and 1.1.3 Type III -Garnet Lac. 1.2 Stick-lac and seed-lac are not covered by this specification.

Standard Specification for Orange Shellac and Other Indian Lacs for Electrical Insulation

IEC 60464-1:1998 电气绝缘漆 第1部分:定义和一般要求

GB/T 1981的本部分涉及电气绝缘用漆。漆可用作覆盖装饰或浸渍， 可在室温或高温下干燥或固化。

Varnishes used for electrical insulation - Part 1: Definitions and general requirements

FZ/T 01052-1998 涂层织物 抗扭曲弯挠性能的测定

本标准规定了涂层织物抗扭曲变挠性能的测定方法。 本标准适用于涂层织物。

Coated fabrics.Determination of resistance to damage by crumpling/flexing

NF C26-285:1996 浸渍剂对漆包线底衬的附着强度测定的试验方法

Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate.