共找到 305 条与 绝缘气体 相关的标准,共 21 页
Low-voltage three-phase squirrel-cage induction motors for general purpose
Cotton-rubber adhesive tapes for electrical insulation
Testing methods for electrical insulating mica products
Testing methods for resistance of thermosetting plastic insulating materials
Technical specifications for the recovery, regeneration and reuse of sulfur hexafluoride gas used in electrical equipment
本标准规定了六氟化硫试验尾气回收的流程和技术要求。 本标准适用于六氟化硫试验尾气的回收,六氟化硫混合气体试验尾气的回收可参照执行。
Technical guidelines for tail gas recovery of sulfur hexafluoride test
本标准规定了基于北斗导航系统的架空输电线路地表形变监测装置的安装、调试及验收要求。 本标准适于用基于北斗导航系统的架空输电线路地表形变监测装置的安装、调试及验收
Monitoring Specifications for Overhead Transmission Lines Based on Beidou Navigation System Part 2: Installation, Commissioning and Acceptance of Ground Monitoring Devices
本标准规定了输变电工程用定扣矩电动扳手的结构组成、基本参数及型号、技术要求、检验规则、试验方法、标志、包装、运输及贮存等 本标准适用于定扭矩电动扳手设计、制造、试验、验收及使用维护。
Constant torque electric wrench for power transmission and transformation engineering
本标准规定了在役输电线路钢制角钢塔、钢管塔和钢管杆腐蚀状态的评估方法。 本标准适用于输电线路钢制角钢塔、钢管塔和钢管杆涂/镀层腐蚀状态评估
Guidelines for assessment of corrosion status of steel towers for transmission lines
Specification of technical grade sulphur hexafluoride (SF6) and complementary gases to be used in its mixtures for use in electrical equipment
This document defines the quality for technical grade sulphur hexafluoride (SF6) and complementary gases such as nitrogen (N2) and carbon tetra-fluoride (CF4), for use in electrical equipment. Detection techniques, covering both laboratory and in-situ portable instrumentation, applicable to the analysis of SF6, N2 and CF4 gases prior to the introduction of these gases into the electrical equipment are also described in this document. This document provides some information on sulphur hexafluoride in Annex A and on the environmental effects of SF6 in Annex B. Information about SF6 by-products and the procedure for evaluating the potential effects of SF6 by-products on human health are covered by IEC 60480, their handling and disposal being carried out according to international and local regulations with regard to the impact on the environment. Handling of SF6 and its mixtures is covered by IEC 62271-4. Procedures to determine SF6 leakages are described in IEC 60068-2-17. For the purposes of this document, the complementary gases used in SF6 mixtures will be limited to N2 or CF4.
Specification of technical grade sulphur hexafluoride (SF6) and complementary gases to be used in its mixtures for use in electrical equipment
1.1 These test methods describe the determination of the water vapor content of electrical insulating gases by direct or indirect measurement of the dew point and the calculation of the water vapor content. 1.2 The following four test methods are provided: 1.2.1 Method A describes the automatic chilled mirror method for measurement of dew point as low as − 73°C (−99°F). 1.2.2 Method B describes the manual chilled mirror or dew cup method for measurement of dew point as low as − 73°C (−99°F). 1.2.3 Method C describes the adiabatic expansion method for measurement of dew point as low as − 62°C (−80°F). 1.2.4 Method D describes the capacitance method for measurement of dew point as low as − 110°C (−166°F). 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warnings, see 8.1.1, 9.2, 10.1.2 and 10.2.5.
Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point
Testing methods for resistance of thermosetting plastic insulating materials
Testing methods for resistance of thermosetting plastic insulating materials
Testing methods for electrical insulating mica products
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号