29.060 电线和电缆 标准查询与下载

ANSI/ATIS 0600028-2021 通信电源系统用直流电源线和电缆. 适用于XHW/XHW-2和DLO/卤化RHH-RHW电缆类型

DC Power Wire and Cable for Telecommunications Power Systems - for XHHW / XHHW-2 and DLO/Halogenated RHH-RHW Cable Types

NEMA HP 8-2021 电气和电子交联改性低烟聚烯烃（XLPO）绝缘连接线，LS型（额定105°C；600 V）、ZHDM型（额定90°C；600 V）、ZHDH型（额定90°C；600 V）、ZH型（额定125°C；600 V）和ZHX型（额定125°C；1000 V）

Electrical and Electronic Cross-Linked, Modified Low-Smoke Polyolefin (XLPO) Insulated Hook-Up Wire, Types LS (Rated 105°C; 600 V), ZHDM (Rated 90°C; 600 V), ZHDH (Rated 90°C; 600 V), ZH (Rated 125°C; 600 V), and ZHX (Rated 125° C; 1000 V)

NEMA HP 5-2021 电气和电子交联改性聚乙烯（XLPE）绝缘125°C连接线，L（600 V）、LL（1000 V）和LX（3000 V）型

Electrical and Electronic Crosslinked, Modified Polyethylene (XLPE) Insulated 125°C Hook-Up Wire, Types L (600 V), LL (1000 V), and LX (3000 V)

LST HD 361 S4-2020 电缆标识系统

System for cable designation

SN/T 5247-2020 进口电线电缆检验技术要求 新能源电动汽车充电电缆

Technical requirements for inspection of imported wires and cables New energy electric vehicle charging cables

DB21/T 3158-2019 绞型电线外径测量方法

Measuring method of twisted wire outer diameter

DB21/T 3155-2019 导体横截面积测量方法

Conductor cross-sectional area measurement method

DB21/T 3157-2019 黄/绿组合色绝缘线芯双色分配比例测量方法

Measuring method of double-color distribution ratio of yellow/green combined color insulated wire core

DB41/T 1709-2018 额定电压300∕500V 风电传感器用耐扭曲软电缆

Rated voltage 300∕500V twist-resistant flexible cable for wind power sensor

DB41/T 1531-2018 额定电压450-750V及以下铜芯橡皮绝缘塑料护套软电缆

Copper core rubber insulated plastic sheathed flexible cable with rated voltage 450-750V and below

DB41/T 1529-2018 额定电压0.6-1kV及以下聚氯乙烯丁腈复合物弹性体绝缘及护套软电缆标准

Standards for Flexible Cables with Polyvinyl Chloride Nitrile Composite Elastomer Insulation and Sheath with Rated Voltage 0.6-1kV and Below

DB41/T 1528-2018 额定电压450/750V及以下弹性体绝缘及护套扁形软电缆

Elastomer insulated and sheathed flat flexible cables with rated voltages up to and including 450/750V

DB41/T 1530-2018 额定电压1kV及以下平行集束导线

Parallel bundled conductors with rated voltage 1kV and below

CAN/CSA C22.2 No.38-2018 热固性绝缘电线和电缆

1.1 This Standard specifies the requirements for single-conductor and multiple-conductor thermoset-insulated wires and cables rated 600 V, 1000 V, 2000 V, and 5000 V, for use in accordance with the rules of the Canadian Electrical Code, Part I, CSA C22.1, in Canada, Standard for Electrical Installations, NOM-001-SEDE, in Mexico, and the National Electrical Code (NEC), NFPA 70, in the United States of America. See Annex A for the complete list of types and voltage ratings covered by this Standard and the specific electrical codes for which they are intended, and Annex B for a summary of construction and test requirements for these types. 1.2 Table 1 provides a summary of the maximum conductor temperature, voltage ratings, and the number of insulated conductors for the types to which this Standard applies. 1.3 This Standard also specifies the requirements for submersible pump cables, with or without jackets, in Deep Well Submersible Water-Pump Cable, Section 7. No type-letter designations are assigned to these cables. 1.4 Products within this Standard might have applications not covered by the electrical codes listed in 1.1.

Thermoset-insulated wires and cables

CAN/CSA C22.2 No.355-2018 密封旋接连接装置

1.1 The wire connectors covered by these requirements are intended for use with copper conductor in accordance with installations covered by the National Electrical Code, NFPA 70; the Canadian Electrical Code, Part I, C22.1; and NOM 001 SEDE, Standard for Electrical Installations. The requirements in this standard cover twist-on style splicing sealed wire connectors intended for installations for applications noted below: a) In accordance with wiring methods where the connector is installed in enclosures rated for the environment and located in dry locations, damp locations, wet locations, below grade, or above grade. b) In lighting systems operating at 30 volts or less (rated 25 amperes and 30 volts, 42.4 volts peak, maximum), and lighting equipment connected to a Class 2 power source; where the connector is located in dry locations, damp locations, wet locations, direct buried locations, below grade, or above grade where protected from direct exposure to sunlight. NOTE: Sealed wire connectors used in these applications do not require the use of an enclosure. c) In Canada, Class 2 circuits located in dry locations, damp locations, wet locations, direct buried locations, below grade, or above grade where protected from direct exposure to sunlight. In the United States and Mexico, Class 2 and Class 3 circuits located in dry locations, damp locations, wet locations, direct buried locations, below grade, or above grade where protected from direct exposure to sunlight. NOTE: Sealed wire connectors used in these applications do not require the use of an enclosure. 1.2 Splicing sealed wire connectors covered by this standard are intended for use with single or multiple conductor underground feeder cable, golf course sprinkler cable, underground low energy cable, irrigation cable, or other cable with insulation acceptable for direct burial, below grade use, or wet locations. 1.3 Splicing sealed wire connectors covered by this standard are intended for use with copper conductor sizes 30 AWG (0.05 mm2) through 6 AWG (13.3 mm2) with currents not exceeding the ampacity of insulated conductors rated either 75 °C (167 °F) or 90 °C (194 °F) and intended for use at 600 V or less. 1.4 For products intended for use in Canada, general requirements are given in CAN/CSA-C22.2 No. 0.

Sealed twist-on connecting devices

GSO IEC 62567:2017 架空线路导线自阻尼特性测试方法

The scope of this Standard is to provide test procedures based on the above-mentioned documents and devoted to minimize the causes of discrepancy between test results, taking into consideration the large experience accumulated in the last 30 years by numerous test engineers and available in literature, including a CIGRE Technical Brochure specifically referring to this standard (see Bibliography). This Standard describes the current methodologies, including apparatus, procedures and accuracies, for the measurement of conductor self-damping and for the data reduction formats.In addition, some basic guidance is also provided to inform the potential user of a given method's strengths and weaknesses. The methodologies and procedures incorporated in this Standard are applicable only to testing on indoor laboratory spans.

Overhead lines - Methods for testing self-damping characteristics of conductors

CSA C22.2 No.75-2017 热塑性绝缘电线电缆

1.1 This Standard specifies the requirements for 600 V single-conductor, thermoplastic-insulated wires and cables, for use as follows: a) In Canada, in accordance with CSA C22.1, Canadian Electrical Code (CE Code), Part I; b) In Mexico, in accordance with NOM-001-SEDE, Standard for Electrical Installations; and c) In the United States, in accordance with ANSI/NFPA 70, National Electrical Code (NEC). Note: See Annex A for the complete list of wire types and voltage ratings covered by this Standard and the specific electrical codes for which they are intended. 1.2 This Standard also specifies the requirements for submersible-pump cables, with or without jackets (see Section 7). No type-letter designations are assigned to these cables. 1.3 In Mexico, the requirements for multiple-conductor thermoplastic-insulated and -jacketed cables rated 600 V are specified in Annex B. In Canada and the United States, requirements for multiple-conductor thermoplastic-insulated and -jacketed cables are covered in other standards. 1.4 Products for which this Standard provides requirements might have applications not described in the electrical codes listed in Clause 1.1.

Thermoplastic-insulated wires and cables

NB/T 42106-2016 铝管支撑性耐热铝合金扩径导线

Aluminum tube supporting heat-resistant aluminum alloy expanded diameter wire

DB41/T 1260-2016 额定电压450/750V及以下固定敷设用铜包铝无护套电缆

Copper-clad aluminum non-sheathed cables for fixed laying of rated voltage 450/750V and below

DB51/T 2174-2016 额定电压10kV钢芯铝绞线架空绝缘电缆 通用技术规范

本标准规定了交流额定电压10 kV钢芯铝绞线架空绝缘电缆产品的术语和定义、符号和代号、使用特性、型号和规格、技术要求、试验方法、验收规则、包装、运输和贮存。 本标准适用于交流额定电压U（Um）为10（12）kV的架空电力线路用钢芯铝绞线交联聚乙烯（XLPE）和高密度聚乙烯（HDPE）绝缘的架空绝缘电缆。

General technical specification for 10kV rated voltage 10kV ACSR overhead insulated cables