29.080.10 绝缘子 标准查询与下载

LST EN 61462-2008 复合空心绝缘子 用于额定电压大于 1000 V 的电气设备的加压和非加压绝缘子 定义、测试方法、验收标准和设计建议（IEC 61462:2007）

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations (IEC 61462:2007)

DS/EN 61462:2008 复合空心绝缘子 用于额定电压大于 1000 V 的电气设备的加压和非加压绝缘子 定义、试验方法、验收标准和设计建议

Applies to composite hollow insulators consisting of a load bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devices at the ends of the insulating tube. Composite hollow insulators as defined in this report are intended to be used under conditions involving internal pressure or free of pressure. They are intended for use in outdoor or indoor electrical equipment operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations

GOST R 52034-2008 陶瓷支撑绝缘子电压超过1000 V.一般规范

Ceramic support insulators for voltage over 1000 V. General specifications

BS EN 61462:2007 复合空心绝缘子.额定电压大于1000 V的电气设备用受压和未受压绝缘子.定义、试验方法、验收标准和设计建议

This International Standard applies to composite hollow insulators consisting of a load-bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devices at the ends of the insulating tube. Composite hollow insulators as defined in this standard are intended for general use (unpressurized) or for use with a permanent gas pressure (pressurized). They are intended for use in both outdoor and indoor electrical equipment operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a rated voltage greater than 1 500 V. This standard does not prescribe impulse voltage or power frequency voltage type tests, nor does it prescribe pollution tests because the withstand voltages are not characteristics of the hollow insulator itself, but of the apparatus of which it ultimately forms a part. All the tests in this standard, apart from the thermal-mechanical test, are performed at normal ambient temperature. This standard does not prescribe tests that may be characteristic of the apparatus of which the hollow insulator ultimately forms a part. Further technical input is required in this area.

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1000 V. Definitions, test methods, acceptance criteria and design recommendations

IEC 61466-1:1997/COR1:2007 额定电压超过1000V的架空线路用复合绝缘子串组合件.第1部分:标准强度等级和终端部件.技术勘误1

This standard is about Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings; Corrigendum 1

Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings; Corrigendum 1

IEC 36C/172/DTS:2007 IEC/TS 62371, Ed. 1.0:额定电压超过1000V的电气设备用空心压力和非压力陶瓷和玻璃绝缘子的特征

IEC/TS 62371, Ed. 1.0: Characteristics of hollow pressurised and unpressurised ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V

SANS 61462:2007 复合空心绝缘子．使用在额定电压大于1000伏的电气设备用受压和未受压绝缘子．定义、试验方法、验收标准和设计建议

Applies to composite hollow insulators consisting of a load-bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devic

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations

JB/T 10583-2006 低压绝缘子瓷件技术条件

本标准规定了低压绝缘子瓷件的技术要求、试验、包装和标志的一般要求。 本标准适用于直流电压低于1000V的或交流电压低于1000V、频率不超过lOOHz的架空电力线路、电气装置和设备上使用的绝缘子瓷件。 本标准不适用于在有破坏瓷及釉的介质（气体或液体）中工作的瓷件。

Technical specifications of porcelain element for low voltage insulators

DL/T 1048-2007 标称电压高于1000V的交流用棒形支柱复合绝缘子.定义、试验方法及验收规则

本标准规定了交流系统中运行的电力设备和装置上的户内和户外复合支柱绝缘子的定义、技术要求、标志和试验分类及检验规则。 本标准适用于标称电压1kV～252kV、频率不超过50Hz的交流系统中运行的电力设备和装置上的户内和户外棒形支柱复合绝缘子(简称绝缘子)。安装地点的海拔高度为1000m及以下，环境温度在-40℃～+40℃之间。 本标准不包含特殊运行条件下选用绝缘子的要求。

Composite post insulators for a.c. with a nominal voltage greater than 1000V.definitions,test methods and acceptance criteria

LST EN 62217-2006/AC-2007 标称电压 > 1 000 V 的室内和室外聚合物绝缘子 一般定义、测试方法和验收标准（IEC 62217:2005）

Polymeric insulators for indoor and outdoor use with a nominal voltage > 1 000 V - General definitions, test methods and acceptance criteria (IEC 62217:2005)

DIN EN 62231:2007 交流电压＞1000V并＜245kV变电站用复合固定柱形绝缘子.定义、试验方法和验收标准

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria (IEC 62231:2006); German version EN 62231:2006

DS/EN 62231:2007 交流电压大于 1000 V 至 245 kV 的变电站用复合站柱式绝缘子 定义、测试方法和验收标准

This Standard applies to composite station post insulators consisting of a load bearing cylindrical insulating solid core made of resin impregnated fibres, a housing (outside the insulating solid core) made of elastomer materials (e.g. silicone or ethylene-propylene) and end fittings attached to the insulating core. Compisite station post insulators covered by this standard are subjected to cantilever, torsion, tension and compression loads. They are intended for substations with a.c. voltages greateder than 1000 V up to 245kV.

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria

LST EN 62231-2007 交流电压大于 1000 V 至 245 kV 的变电站用复合站柱绝缘子 定义、测试方法和验收标准（IEC 62231:2006）

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria (IEC 62231:2006)

BS EN 62231:2007 交流电压＞1000V且＜245kV变电站用复合固定柱形绝缘子.定义、试验方法和验收标准

This International Standard applies to composite station post insulators consisting of a load bearing cylindrical insulating solid core made of resin impregnated fibres, a housing (outside the insulating solid core) made of elastomer material (e.g. silicone or ethylene-propylene) and end fittings attached to the insulating core. Composite station post insulators covered by this standard are subjected to cantilever, torsion, tension and compression loads. They are intended for substations with a.c. voltages greater than 1 000 V up to 245 kV. The object of this standard is – to define the terms used, – to prescribe test methods, – to prescribe acceptance or failure criteria. This standard does not include requirements dealing with the choice of insulators for specific operating conditions.

Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria

IEC 61462:2007 复合空心绝缘子.使用在额定电压大于1000伏的电气设备用受压和未受压绝缘子.定义、试验方法、验收标准和设计建议

This International Standard applies to composite hollow insulators consisting of a load-bearing insulating tube made of resin impregnated fibres, a housing (outside the insulating tube) made of elastomeric material (for example silicone or ethylene-propylene) and metal fixing devices at the ends of the insulating tube. Composite hollow insulators as defined in this standard are intended for general use (unpressurized) or for use with a permanent gas pressure (pressurized). They are intended for use in both outdoor and indoor electrical equipment operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct current equipment with a rated voltage greater than 1 500 V.

Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1000 V - Definitions, test methods, acceptance criteria and design recommendations

KS C IEC 61264:2006 甜食高压设备和控制设备压缩空心陶瓷绝缘子

Ceramic pressurized hollow insulators for high－voltage switchgear and controlgear

KS C 3833-2006(2021) 6.6 kV耐张绝缘子

6.6 kV strain insulators

KS C 3834-2006 供电线用悬式绝缘子

이 규격은 전기 철도용 급전선로에 사용하는 자기제의 핀 애자(이하 애자라고 한다.)에 대하

Pin type insulators for feeder

KS C 3833-2006 6.6kV拉紧绝缘子

이 규격은 주로 고압 가공 전선로에 사용되는 지름 102 mm, 높이 178 mm의 클레비

6.6 kV strain insulators

KS C 3834-2006(2021) 馈线用针式绝缘子

Pin type insulators for feeder