29.120.20 连接装置 标准查询与下载

LST EN IEC 60320-2-4:2021 家用和类似一般用途的器具耦合器 第 2-4 部分：取决于器具重量的耦合器（IEC 60320-2-4:2018）

Appliance couplers for household and similar general purposes - Part 2-4: Couplers dependent on appliance weight for engagement (IEC 60320-2-4:2018)

T/CEC 450-2021 高压隔离开关及通流回路接触面喷涂检修工艺导则

本文件规定了高压隔离开关及通流回路接触面纳米导电剂喷涂检修的检修分类及周期、检修条件、检修项目和内容、检修工艺要求、试验、检修后效果评估等。 本文件适用于 10 kV 及以上电压等级交直流敞开式高压隔离开关及通流回路接触面部件纳米导电剂（具体技术参数见附录 A）喷涂检修工作，包括但不限于高压隔离开关触头、触指、导电臂连接部位、设备接线板、线夹等在运行过程中出现过热或检测过程中回路电阻超标的设备（部件）；高压隔离开关进行例行检修时适用本文件；其他设备（如手车断路器、敞开式断路器、环网柜断路器、环网柜隔离开关、通流母线排等）的通流回路接触面部件的喷涂检修可参考本文件。

Guidelines for Spraying Maintenance Process of Contact Surfaces of High Voltage Isolating Switches and Flow Circuits

BS EN IEC 60320-2-4:2021 家用和类似一般用途的电器耦合器 联轴器的接合取决于设备重量

Appliance couplers for household and similar general purposes. Couplers dependent on appliance weight for engagement

DS/EN IEC 60320-2-4:2021 家用和类似用途的器具耦合器 第 2-4 部分：取决于器具重量的耦合器接合

Appliance couplers for household and similar general purposes – Part 2-4: Couplers dependent on appliance weight for engagement

PN-EN IEC 60352-4-2021-03 E 无焊连接 第4部分：不可触及的绝缘位移（ID）连接 一般要求、测试方法和实用指南（IEC 60352-4:2020）

Solderless connections -- Part 4: Non-accessible insulation displacement (ID) connections -- General requirements, test methods and practical guidance (IEC 60352-4:2020)

BS EN IEC 60352-7:2021 无焊连接 第7部分：弹簧夹连接 一般要求，试验方法和实用指南

Solderless connections. Spring clamp connections. General requirements, test methods and practical guidance

PN-EN IEC 60352-3-2021-01 E 无焊连接 第3部分：可触及的绝缘位移（ID）连接 一般要求、测试方法和实用指南（IEC 60352-3:2020）

Solderless connections -- Part 3: Accessible insulation displacement (ID) connections -- General requirements, test methods and practical guidance (IEC 60352-3:2020)

IEC 61534-21:2021 电力轨道系统第21部分:用于墙壁和天花板安装的电力轨道系统的特殊要求

Powertrack systems - Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting

IEC 61534-22:2021 电力轨道系统第22部分:地面或地下安装电力轨道系统的特殊要求

Powertrack systems - Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation

KS C 2618-2020 压缩端子

Compression terminals

KS C 8461-2020 刚性金属导管的表面附件

Surface accessary for rigid metal conduits

KS C 2621-2020 用于铜导体的非绝缘压接式套管

Non-insulated crimp-type sleeves for copper conductors

DIN EN IEC 61238-1-3:2020 电力电缆的压缩和机械连接器. 第1-3部分: 在非绝缘导体上试验的额定电压高于1 kV(Um = 1.2 kV)至36 kV(Um = 42 kV)的电力电缆的压缩和机械连接器的试验方法和要求(IEC 61238-1-3-2018); 德文版 EN IEC 61238-1-3-2019 + A11-2019

This part of IEC 61238-1 applies to compression and mechanical connectors for power cables for rated voltages above 1 kV (Um = 1,2 kV) up to 36 kV (Um = 42 kV), e. g. buried cables or cables installed in buildings, having conductors complying with IEC 60228 having nominal cross-s

Compression and mechanical connectors for power cables - Part 1-3: Test methods and requirements for compression and mechanical connectors for power cables for rated voltages above 1 kV (Um = 1,2 kV) up to 36 kV (Um = 42 kV) tested on non-insulated conduc

DIN EN IEC 61238-1-2:2020 电力电缆的压缩和机械连接器. 第1-2部分: 在绝缘导体上试验的额定电压高达 1 kV(Um = 1.2 kV)的电力电缆的绝缘穿刺连接器的试验方法和要求(IEC 61238-1-2)-2018); 德文版 EN IEC 61238-1-2-2019

This part of IEC 61238-1 applies to insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV), e. g. buried cables or cables installed in buildings, having conductors complying with IEC 60228 having nominal cross-sectional areas between 2,5 mm2 a

Compression and mechanical connectors for power cables - Part 1-2: Test methods and requirements for insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV) tested on insulated conductors (IEC 61238-1-2:2018); German ve

DIN EN IEC 61238-1-1:2020 电力电缆的压缩和机械连接器. 第1-1部分: 在非绝缘导体上试验的额定电压高达1 kV(Um = 1.2 kV)的电力电缆的压缩和机械连接器的试验方法和要求(IEC 61238- 1-1-2018); 德文版 EN IEC 61238-1-1-2019

This part of IEC 61238-1 applies to compression and mechanical connectors for power cables 116 for rated voltages up to 1 kV (Um = 1,2 kV), e. g. buried cables or cables installed in buildings, having conductors complying with IEC 60228 having nominal cross-sectional areas betwee

Compression and mechanical connectors for power cables - Part 1-1: Test methods and requirements for compression and mechanical connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV) tested on non-insulated conductors (IEC 61238-1-1:2018)

ASTM B389-81(2020) 温控金属螺旋和螺旋线圈​​热挠曲率的标准测试方法

1.1 This test method covers the determination of the thermal deflection rate of spiral and helical coils of thermostat metal. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal Deflection Rate of Spiral and Helical Coils of Thermostat Metal

ASTM B362-91(2020) 温控金属螺旋线圈机械扭矩的标准测试方法

1.1 The test method covers the principles of determining the mechanical torque rate of spiral coils of thermostat metal. NOTE 1—This test method has been developed particularly to cover the determination of the mechanical torque rate of spiral coils made of thermostat metal for carburetors and manifold heat controls. The method is not limited to thermostat metals and can be used for spiral coils of other materials for which the torque rate must be measured accurately. 1.2 The values stated in inch-pound units are to be regarded as the standard. The metric equivalents of inch-pound units may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Mechanical Torque Rate of Spiral Coils of Thermostat Metal

BS EN IEC 60352-4:2020 无焊连接 不可触及的绝缘刺破 (ID) 连接 一般要求、测试方法和实践指导

What is BS EN IEC 60352 ‑ 4 about?   BS EN IEC 60352 ‑ 4 is a multi-part series of European standard which discusses about the solderless connection.    BS EN IEC 60352 ‑ 4 is applicable to non-accessible ID connections for which the tests and measurements according to Clauses 6 through 8 are suitable and which are made with:  

Solderless connections - Non-accessible insulation displacement (ID) connections. General requirements, test methods and practical guidance

EN IEC 60352-4:2020 无焊连接 第4部分：不可触及的绝缘位移（ID）连接 一般要求、测试方法和实用指南

IEC 60352-4:2020 is applicable to non-accessible ID connections for which the tests and measurements according to Clauses 6 through 8 are suitable and which are made with: – appropriately designed ID terminations; – wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; – wires having stranded conductors of 0,05 mm2 to 10 mm2 cross-sectional area; for use in electrical and electronic equipment and components. Information on materials and data from industrial experience is included in addition to the test procedures to provide electrically stable connections under prescribed environmental conditions. There are different designs and materials for ID terminations in use. For this reason, only fundamental parameters of the termination are specified, while the performance requirements of the wire and the complete connection are specified in full detail. The purpose of this document is: – to determine the suitability of non-accessible ID connections under specified mechanical, electrical and atmospheric conditions; – to provide a means of comparing test results when the tools used to make the connections, if any, are of different designs or manufacture. This second edition cancels and replaces the first edition, published in 1994, and its Amendment 1 (2000). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Transferred Clauses 9 to 13 into Annex A (informative). b) The figures were re-drawn for clarity.

Solderless connections - Part 4: Non-accessible insulation displacement (ID) connections - General requirements, test methods and practical guidance

BS EN IEC 60352-3:2020 无焊连接 可触及的绝缘刺破 (ID) 连接 一般要求、测试方法和实践指导

What is BS EN IEC 60352 ‑ 3 about?     BS EN IEC 60352 ‑ 3 is a multi-part series of European standard which discusses about the solderless connections.    BS EN IEC 60352 ‑ 3 is applicable to ID connection which are accessible for tests and measurements according to Clauses 6 through 8 and which are made with:  

Solderless connections - Accessible insulation displacement (ID) connections. General requirements, test methods and practical guidance