29.120.30 插头、插座、连接器 标准查询与下载

GSO IEC 60309-2:2023 工业用插头、固定式或便携式插座和器具输入插座 第2部分：插针和接触管配件的尺寸兼容性要求

IEC 60309-2:2021 applies to plugs, fixed or portable socket-outlets, and appliance inlets, hereinafter referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 125 A, primarily intended for industrial use, either indoors or outdoors. This fifth edition cancels and replaces the fourth edition published in 1999, Amendment 1:2005 and Amendment 2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: addition of requirements and test for non-solid pins; additional rating IPX9; additional marking to indicate neutral terminal and/or earthing terminal. This document is to be read in conjunction with IEC 60309-1:2021.

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Part 2: Dimensional compatibility requirements for pin and contact-tube accessories

T/CNFA 025-2023 家具配电单元安装要求

本文件规定了家具配电单元的术语和定义、基本要求、标志与警示、安全要求、安装要求。 本文件适用于室内使用的家具上及类似用途的家具配电单元（额定电压在50V以上但不超过250V、额定电流不超过16A），允许办公连接配电主线额定电流不超过20A。 本文件规定了家具配电单元适合使用的环境温度。

Furniture distribution unit installation requirements

KS C IEC TR 60083-2023 IEC成员国标准化的家用和类似通用插头和插座

Plugs and socket outlets for domestic and similar general use standardized in member countries of IEC

KS C IEC 60906-2-2023 IEC家用和类似用途插头和插座系统.第2部分:15 A 125 V AC和20 A 125 V交流电插头和插座

IEC system of plugs and socket-outlets for household and similar purposes — Part 2: Plugs and socket-outlets 15 A 125 V AC and 20 A 125 V AC

KS C IEC 60320-2-1-2023 家用和类似用途电器耦合器第2-1部分:缝纫机耦合器

Appliance couplers for household and similar general purposes ― Part 2-1：Sewing machine couplers

KS C IEC 60906-1-2023 IEC家用和类似用途插头和插座系统.第1部分:16 A 250 V AC插头和插座

IEC system of plugs and socket-outlets for household and similar purposes — Part 1: Plugs and socket-outlets 16 A 250 V AC

KS C IEC 60884-2-4-2023 家用和类似用途的插头和插座.第2-4部分:SELV插头和插座的特殊要求

Plugs and socket-outlets for household and similar purposes — Part 2-4: Particular requirements for plugs and socket-outlets for SELV

23/30466423 DC BS IEC 60884-2-3 家用和类似用途的插头和插座 第 2-3 部分 固定安装用不带联锁装置的开关插座的特殊要求

BS IEC 60884-2-3. Plugs and socket-outlets for household and similar purposes - Part 2-3. Particular requirements for switched socket-outlets without interlock for fixed installations

23/30466427 DC BS IEC 60884-2-7 家用和类似用途的插头和插座 第 2-7 部分 延长线装置的特殊要求

BS IEC 60884-2-7. Plugs and socket-outlets for household and similar purposes - Part 2-7. Particular requirements for cord extension sets

T/CES 184-2022 中低压配电网快速插拔电缆连接器配置技术导则

中国电工技术学会团体标准T/CES 184-2022《中低压配电网快速插拔电缆连接器配置技术导则》由中国电工技术学会提出，东莞市纳百川电子科技有限公司等单位起草编制完成。该标准规定了中低压配电网架空线路、柱上配变台区、配电站房及预装式变电站等新建、改扩建时装设快速插拔电缆连接器的配置原则、配置要求、装设位置及产品选型等方面技术要求。

Technical guide for configuration of quick plug-pull cable connectors for medium and low voltage distribution networks

KS C IEC 60309-2-2022 工业用插头、固定或便携式插座和器具插座.第2部分:插针和接触管附件的尺寸兼容性要求

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes — Part 2: Dimensional compatibility requirements for pin and contact-tube accessories

KS C IEC 60309-1:2022 工业用插头、固定或便携式插座和器具插座.第1部分:一般要求

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes — Part 1: General requirements

KS C IEC 60309-2:2022 工业用插头、固定或便携式插座和器具插座.第2部分:插针和接触管附件的尺寸兼容性要求

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes — Part 2: Dimensional compatibility requirements for pin and contact-tube accessories

KS C IEC 60309-1-2022 工业用插头、固定或便携式插座和器具插座.第1部分:一般要求

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes — Part 1: General requirements

BS EN 60320-3:2014+A2:2022 家用和类似通用用途的器具耦合器 标准板材和仪表

This part of the lEC 60320 sets the dimensions for appliance couplers for two poles and two poles with earth contact – for the connection of electrical devices for household and similar onto the mains supply and – for the interconnection of the electrical supply to appliance or equipment – and dimensions for gauges.

Appliance couplers for household and similar general purposes - Standard sheets and gauges

EN IEC 62196-2:2022 插头、插座、车辆连接器和车辆入口 电动车辆的传导充电 第2部分：AC 插针和接触管附件的尺寸兼容性要求

This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles. This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1. NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS). These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals. The use of these accessories for bidirectional power transfer is under consideration. This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C. NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO. NOTE 3 In the following country, −35 °C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in IEC 61851-1:2017.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories

EN IEC 62196-3:2022 插头、插座、车辆连接器和车辆入口 电动车辆的传导充电 第3部分：DC 和 AC/DC 插针和接触管车辆耦合器的尺寸兼容性要求

This part of IEC 62196 is applicable to vehicle couplers with pins and contact tubes of standardized configuration, herein also referred to as "accessories", intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage and current in accordance with IEC 62196-1:2022. This document applies to high power DC interfaces and combined AC/DC interfaces of vehicle couplers that are intended for use in conductive charging systems for circuits specified in IEC 61851-1:2017 and IEC 6185123:-2. The DC vehicle connectors and inlets covered by this document are used only in charging mode 4, according to IEC 618511:2017, 6.2.4, and case C, as shown in IEC 618511:2017, Figure 3. These vehicle couplers are intended to be used for circuits specified in IEC 61851-23: - which operate at different voltages, and which can include ELV and communication signals. This document applies to the vehicle couplers to be used in an ambient temperature between -30 °C and +40 °C. NOTE 1 In some countries, other requirements may apply. NOTE 2 In the following country, −35 °C applies: SE. These vehicle couplers are intended to be connected only to cables with copper or copper-alloy conductors.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility requirements for DC and AC/DC pin and contact-tube vehicle couplers

EN IEC 62196-1:2022 插头、插座、车辆连接器和车辆插座 电动车辆的传导充电 第1部分：一般要求

This part of IEC 62196 is applicable to EV plugs, EV socket-outlets, vehicle connectors, vehicle inlets, herein referred to as "accessories", and to cable assemblies for electric vehicles (EV) intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding: - 690 V AC 50 Hz to 60 Hz, at a rated current not exceeding 250 A; - 1 500 V DC at a rated current not exceeding 800 A. These accessories and cable assemblies are intended to be installed by instructed persons (IEV 195-04-02) or skilled persons (IEV 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC 61851 (all parts), which operate at different voltages and frequencies, and which can include extra-low voltage and communication signals. These accessories and cable assemblies are intended to be used at an ambient temperature between −30 °C and +40 °C. NOTE 1 In some countries, other requirements can apply. NOTE 2 In the following country, −35 °C applies: SE. NOTE 3 The manufacturer can enlarge the temperature range on the condition that the specified range information is provided. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this document are intended for use in electric vehicle supply equipment in accordance with IEC 61851 (all parts). This document does not apply to standard plug and socket-outlets used for mode 1 and mode 2 according to IEC 61851-1:2017, 6.2. NOTE 4 In the following countries, mode 1 is not allowed: UK, US, CA, SG.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

BS EN IEC 60309-2:2022 工业用插头、固定式或便携式插座和器具入口 插针和接触管配件的尺寸兼容性要求

1   Scope This document applies to plugs, fixed or portable socket-outlets, and appliance inlets, hereinafter referred to as accessories, with a rated operating voltage not exceeding 1 000 V DC or 1 000 V AC with a frequency not exceeding 500 Hz and a rated current not exceeding 125 A, primarily intended for industrial use, either indoors or outdoors. These accessories are intended to be installed by instructed persons or skilled persons only. NOTE 1 All references for accessories with a rated current of more than 125 A in IEC 60309‑1 are not applicable to this document. This document applies to accessories with pins and contact-tubes of standardize d configurations. This document applies to accessories, for use when the ambient temperature is normally within the range −25 °C to 40 °C. The use of these accessories on building sites and for agricultural, commercial and domestic applications is not precluded. This document applies to accessories with screwless-type terminals or insulation piercing terminals, with a rated current up to and including 32 A for series I and 30 A for series II. Socket-outlets or appliance inlets incorporated in or fixed to electrical equipment are within the scope of this document. This document also applies to accessories intended to be used in extra-low voltage installations. NOTE 2 This document does not apply to accessories primarily intended for domestic and similar ...

Plugs, fixed or portable socket-outlets and appliance inlets for industrial purposes - Dimensional compatibility requirements for pin and contact-tube accessories

IEC 60799:2018+AMD1:2022 CSV 电气附件.电线组和互连电线组

Electrical accessories - Cord sets and interconnection cord sets