29.130.10 高压开关装置和控制器 标准查询与下载

GB 1984-2003 高压交流断路器

本标准适用于设计安装在户内或户外且运行在频率为50Hz、电压3000V及以上的系统中的交流断路器。 本标准仅适用于三相系统中的三极断路器和单相系统中的单极断路器。用于单相系统中的两极断路器及用于频率低于50Hz时应遵从制造厂和用户之间的协议。 本标准也适用于断路器的操动机构和其辅助设备。然而，本标准不涉及仅依靠人力操动合闸机构的断路器，因为它不能规定额定短路关合电流，而且从安全的角度考虑，这种仅靠人力操作的方式是不应该提倡的。 本标准不涉及用于电力牵引设备的移动电站中的断路器。他们包含在IEC 60077［4」中。 安装在发电机和升压变压器之间的发电机断路器也不包含在本标准的范围内。 感性负载开合包含在IEC 61233中。 除单极自动重合闸的断路器外，具有预定的极间不同期性的断路器不包含在本标准的范围内。 本标准不涉及具有机械脱扣装置或不能失效的装置的自脱扣断路器。 与线路串联电容器和其保护设备并联的旁路断路器不包含在本标准的范围内，它们包含在IEC 60143－2[6］中。

High-voltage alternating-current circuit-breakers

GB/T 14808-2001 交流高压接触器和基于接触器的电动机起动器

本标准适用于额定电压3.6 kV及以上但不超过12 kV，频率50 Hz及以下电力系统中使用的户内安装的交流接触器和/或基于接触器的电动机起动器。 本标准仅适用于三相系统中的三极接触器和起动器，以及用于单相系统中的单极接触器和起动器。 用于单相系统中的两极接触器和起动器应由制造厂和用户协商。 本标准涉及的接触器和/或起动器一般不用于开断短路电流，因此，适当的短路保护(见3．4．110．12和下面的注2)可以是装置的一部分，但未必成为接触器或起动器的一部分。 本标准对下列装置提出要求： ——与过载和/或短路保护装置(SCPD)有关的接触器； ——与单独的短路保护装置和/或单独的短路以及与其成为一体的过载保护装置有关的起动器； ——根据规定的条件，与本身的短路保护装置组合在一起的接触器或起动器。这些组合电器，例如综合起动器(见3．4．110．9)，被看作是一个整体。 本标准涉及到用于合、分电路的接触器，以及，如果与合适的继电器(见3．6．108)组合，保护线路可能出现的过负载的接触器。 本标准也适用于接触器的操作装置及其辅助设备。 本标准涉及到用来起动电动机并将其加速至正常速度、保证电动机连续运行、切断电动机电源为电动机及其连接的回路的过负载提供保护的电动机起动器。 电动机起动器的类型包括： ——直接起动器 ——反转起动器 ——双向起动器 ——降低电压起动器 ——自耦减压起动器 ——变阻起动器 ——电抗起动器 动作取决于符合GB/T 14598．15的用来保护电动机的热继电器，或符合GB l3232的电动机装有的热保护装置的起动器不需要满足本标准的相关要求。

High-voltage alternating current contactors and contactor-based motor-starters

BS EN IEC 62271-214:2024 高压开关设备和控制设备 额定电压1kV以上至52kV（含）的交流金属封闭柱式开关设备和控制设备的内部电弧分类

High-voltage switchgear and controlgear - Internal arc classification for AC metal-enclosed pole-mounted switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

24/30493420 DC 高压开关设备和控制设备 第3部分：基于 IEC 61850 的数字接口

BS EN IEC 62271-3 High-voltage switchgear and controlgear - Part 3: Digital interfaces based on IEC 61850

T/EPIAJL 10-2024 高压隔离开关和接地 开关低温适应性技术条件与运行维护导则

本标准规定低温环境户外敞开式高压隔离开关和接地开关的低温适应性技术要求、试验项目、试验方法、校验规则以及运行与维护要求，填补国家标准及行业标准对环境温度低于-25℃户外敞开式高压隔开开关和接地开关的技术空白，保证高压开关设备低温环境下的可靠运行。

Technical requirements and operation maintenance requirements for high-voltage disconnector and earthing switches in low temperature

T/QGCML 3179-2024 高压成套开关柜

本文件规定了高压成套开关柜的术语和定义、基本参数、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于高压成套开关柜的设计及检验。

High voltage complete switch cabinet

T/QGCML 3180-2024 柱上断路器维修服务规范

本文件规定了柱上断路器维修服务规范的术语和定义、分类、维修准备、维修前的检查及试验、检修记录、投运准备。 本文件适用于柱上断路器维修服务规范。

Pole-mounted circuit breaker maintenance service specifications

T/QGCML 2933-2024 户内金属铠装移开式开关设备

本文件规定了户内金属铠装移开式开关设备的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于户内金属铠装移开式开关设备的制造和检验。

Indoor metal armored removable switchgear

BS EN IEC 62271-103:2023 高压开关设备和控制设备 额定电压高于 1 kV 至 52 kV 的交流开关

High-voltage switchgear and controlgear - Alternating current switches for rated voltages above 1 kV up to and including 52 kV

T/GSEE 0011-2023 高压交流电路半导体开关设备技术规范

本标准共9章，包括： （1）范围 本标准适用于设计安装在户内或户外且运行频率为50 Hz/60 Hz、电压3kV及以上，最高电压40.5kV的高压交流电路的电子式开关。 本标准规定了使用可控和（或）不可控电子阀器件的高压交流电路半导体电子式开关的技术要求、检验方法、包装运输等内容。 （2）规范性引用文件 本标准引用了7个国家标准。 （3）术语和定义 （4）结构和控制 （5）正常使用条件 （6）标识和代号 （7）技术参数及性能要求 （8）阀器件组件及半导体开关试验 （9）标志、包装、运输和贮存

Technical specifications for high-voltage AC circuits semiconductor switchgear

T/ZSDX 0001-2023 12kV常压密封空气绝缘开关设备和控制设备

1. 常压密封：常压密封的作用防止受到外界环境影响，控制外部水分浸入充气隔室内部而降低设备的绝缘性能。箱体内无压力，无泄漏风险，主开关零压即为运行状态，提高设备的运行可靠性和运行寿命，以保障绝缘可靠性。与同类产品相比较，不再充气体，带电体安全距离大于空气中国标要求等明显优势。 2. 空气绝缘：气体不经任何处理，通过改进结构及加工工艺，以及选用高性能材料，优化电场的方式，生产和使用环节均不使用、不排放无温室效应气体，既满足小型化有节能环保的需求。 3. 小型化：比常规XGN15体积小一半以上，与同类别充气柜体积接近。可大幅减小配电房占地和空间，降低建造成本。 4. 在基本要求(产品设计、原材料、关键技术、工艺、设备等方面)、质量保证方面的先进性体现。

12kV normal pressure sealed air insulated switchgear and control equipment

BS EN IEC 62271-105:2023 高压开关设备和控制设备 额定电压高于 1 kV 至 52 kV 的交流开关熔断器组合

High-voltage switchgear and controlgear - Alternating current switch-fuse combinations for rated voltages above 1 kV up to and including 52 kV

T/QGCML 2132-2023 配电控制用高压进线柜

本文件规定了配电控制用高压进线柜的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于配电控制用高压进线柜的生产及检验。

High voltage entry cabinet for power distribution control

IEC 62271:2023 SER

GSO IEC 62271-200:2023 高压开关设备和控制设备 第200部分：额定电压1 kV以上且52 kV以下的交流金属封闭开关设备和控制设备

IEC 62271-200:2021 is applicable to prefabricated metal‑enclosed switchgear and controlgear assemblies designed for: – alternating current; – rated voltages above 1 kV and up to and including 52 kV; – service frequencies up to and including 60 Hz; – indoor and outdoor installation. The assembly can include air-insulated and/or fluid-filled compartments. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) clause numbering aligned with IEC 62271‑1:2017, including the adoption of the subclause names of Clause 3; b) in Clause 3 specific definitions are added for "in service", "normal operating condition" and "normal use"; c) internal arc testing on pole-mounted switchgear is taken out of this document, as it is now covered by the specific standard IEC 62271‑214:2019; d) a more precise description of earthing circuit is given with the inclusion of ratings and test requirements; e) number of mechanical tests on interlocks is reduced for type testing; a more precise description of forces to apply during type testing is given (refer to 7.102); f) resistance measuring on main circuit is only needed before continuous current tests (as reference for routine tests) and no longer needed after this continuous current test. Rationale for this deletion is that this measured resistance does not mean anything; as the temperature rise test was just finished, a new temperature rise test will not give new information; g) IEC 62271-100:2021, IEC 62271-103:2021, IEC 62271-105:2021 and IEC 62271-106:2021 are referred to in the document; h) IEC 62271‑107:2019 and IEC IEEE 62271‑37‑013:2015 are also considered in 7.101.2; i) a more precise description of LSC category is given with the inclusion of an explanatory flowchart (Annex D); j) examples not covered by the IAC test are transferred from Clause 6 to 9.103; k) the term "assembly" is defined in Clause 3 and used as synonym for "metal-enclosed switchgear and controlgear" in this document; l) "metallic" is replaced by "metal" where applicable; m) 6.105 is now covered by 7.7; n) a 1 s rule was introduced for Criterion 4 during IAC tests regarding hot gases versus glowing particles as cause of ignition; o) a more precise description of internal arc tests for switchgear with protrusions is given in Annex A.

High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

GSO IEC 62271-1:2023 高压开关设备和控制设备 第1部分：交流开关设备和控制设备通用规范

IEC 62271-1:2017 applies to AC switchgear and controlgear designed for indoor and/or outdoor installation and for operation at service frequencies up to and including 60 Hz and having rated voltages above 1 000 V. This document applies to all high-voltage switchgear and controlgear except as otherwise specified in the relevant IEC standards for the particular type of switchgear and controlgear. This second edition cancels and replaces the first edition published in 2007 and Amendment 1:2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: New numbering in accordance with ISO/IEC directives, Part 2 (2016) and IEEE Std. C37.100.1. 4.1.2 a) The normal service condition for indoor switchgear is limited to one range of 40 °C to -5 °C. 4.1.3 a) The normal service condition for outdoor switchgear is limited to one range of 40 °C to -25 °C. 4.2.2: The specifications from IEC 60071-2:1996 are adopted for altitude correction factors above 1 000 m. 5.2.2: Range I, the rated voltage of 40,5 kV is added Series I Table 1; Table 2 and Table 4 are updated on recommendation of the US National Committee. 6.8: New subclause added for manual operated actuators consistent with “Man Machine Interface” recommendations of IEC 60447 . 7.2.6.1:Insert the wording regarding preliminary impulses across open vacuum interrupters according to the result of IEC 17/1026/RQ. 7.3: Changed the requirement for radio interference voltage to a rated voltage level of 245 kV and above, instead of 123 kV and above. This change is based on reported positive test and service experience of utility representatives in the maintenance team of this standard. 7.5.6, Table 14: a. Introduced the distinction of parts in “OG” (oxidizing gas) or in “NOG” (not oxidizing gas) replacing the former “air” and “SF6”; b. Increased the allowable temperature rise for some parts in groups 1 and 2 of Table 14 according to IEC TR 60943; c. Expanded the definition of allowable temperature rise for categories of accessible surfaces with reference to IEC Guide 117. See also Point 15 in 7.5.6.2. 7.5.6.2: Point 5 is modified to clarify the introduction of “OG” and “NOG” gas. 7.10: Some tests were removed because the relevant test standards of IEC 60068 series were modified or withdrawn. 7.11.3: The acceptance criteria for X-radiation testing are modified to recognize higher rated vacuum interrupters. Former informative Annex H: Corrosion is deleted, the content is part of IEC TR 62271-306. New Annex J (informative): Added informative guidelines for the extension of validity of type tests New Annex K (informative): Added informative guidelines about exposure to pollution The contents of the Interpretation Sheet 1 of May 2021 have been included in this copy.

High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear

GSO IEC TR 62063:2023 高压开关设备和控制设备 电子及相关技术在开关设备和控制设备辅助设备中的应用

This technical report is intended to provide basic guidance for the introduction of improvements in the IEC standards related to HV switchgear and controlgear. Such improvements are required to allow the users of switchgear to benefit from all the possibilities provided by electronic equipment.

High-voltage switchgear and controlgear - The use of electronic and associated technologies in auxiliary equipment of switchgear and controlgear

T/QGCML 1297-2023 12kV 环保气体绝缘环网开关设备和控制设备

本文件规定了12 kV环保气体绝缘环网开关设备和控制设备的术语和定义、使用条件、额定值、技术要求、试验方法、检验规则、标志、包装、运输和贮存、安全、产品对环境的影响。 本文件适用于额定电压为12 kV、户内安装的、频率为50 Hz的环保气体绝缘环网开关设备和控制设备（以下简称环网柜）。

12kV environmentally friendly gas insulated ring network switchgear and control equipment

23/30474862 DC BS EN IEC 62271-201 高压开关设备和控制设备 第 201 部分：额定电压高于 1 kV 并高达 52 kV 的交流固体绝缘封闭式开关设备和控制设备

BS EN IEC 62271-201. High-voltage switchgear and controlgear - Part 201. AC solid-insulation enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV

DL/T 2606-2023 直流转换开关振荡特性现场试验方法

本文件规定了直流转换开关振荡特性现场试验的试验原理、试验条件、仪器设备、试验步骤、试验数据处理和试验报告等要求。 本文件适用于高压直流输电系统用金属回线转换开关、大地回线转换开关、中性母线开关和中性母线接地开关等直流转换开关的振荡特性现场试验。

Field test method for oscillation characteristics of DC transfer switch