29.140.01 电灯综合 标准查询与下载

EN IEC 63103:2020 照明设备 非主动模式功率测量

IEC 63103:2020(E) specifies methods of measurement of electrical power consumption in non-active mode(s), as applicable for electrical lighting equipment. This includes electrical lighting equipment incorporating non-illumination components. This document specifies neither performance requirements nor limits on power consumption. This document applies to lighting equipment connected to a supply voltage up to 1 500 V DC or up to 1 000 V AC. This document is intended to be referenced by lighting equipment product standards for the measurement of non-active mode power consumption. Details for the non-active mode power consumption measurement and data presentation are specified in the product standards.

Lighting equipment - Non-active mode power measurement

EN IEC 63129:2020 照明产品浪涌电流特性的测定

IEC 63129:2020 describes a method, based on measurements combined with calculations, to determine specific characteristics of the inrush current of single and/or multiple lighting products of the same type. Lighting products include the following: light sources with integrated controlgear, controlgear, luminaires.

Determination of inrush current characteristics of lighting products

KS C 7705-2019 灯具玻璃泡的命名方法

Designation Method for Glass Bulbs of Lamps

KS C 7708-2019 灯具测试方法通则

General Rules of Testing Method for Lamps

T/CEEIA 377-2019 绿色设计产品评价技术规范　读写作业台灯

本标准规定了读写作业台灯的绿色设计产品的评价原则和方法、对组织的要求、评价指标以及产品生命周期评价方法及报告格式要求。 本标准适用于在家庭、教室和类似场所作为读写照明用的台灯和宣称“护眼”的台灯。 注：本标准中读写作业台灯均称为“产品”。

Technical specification for green-design product assessment — Table lamp for paper task

T/CEEIA 373-2019 绿色设计产品评价技术规范 自镇流LED灯

本标准规定了自镇流LED灯的绿色设计产品的评价原则和方法、对组织的要求、评价指标以及产品生命周期评价方法及报告格式要求。 本标准适用于以下范围的普通照明用50V以上自镇流LED灯： ——额定功率在60W以下； ——额定电压大于50V且小于或等于250V；且 ——使用符合IEC60061-1要求的E14和E27灯头。 注：本标准中自镇流LED灯均称为“产品”。

Technical specification for green-design product assessment — Self-ballasted LED lamps

T/SZSA 024.5-2019 室内健康照明设计规范 第5部分：教室照明

前言 引言 1 范围 2 规范性引用文件 3 术语和定义 4 基本规定 5 技术要求 6 测试方法 参考文献 本部分应与T/SZSA 024.1一起使用。 本部分适用于中小学教室及场所的照明设计依据。 其他类似场所照明设计可参照执行。 本部分不适用于除教室等教学场所以外的照明设计。 注：除非有特别指明是其他场所的照明，在本标准中出现的“教室照明”代表“中小学教室场所照明”

Indoor Healthy Lighting Design Code Part 5: Classroom Lighting

T/ZALI 0006-2019 普通照明用集成式LED灯丝灯 性能要求

本标准规定了普通照明用非定向集成式LED灯丝灯的术语和定义、分类与命名、要求、试验方法和检验规则。 本标准适用于在家庭和类似场合作为普通照明用、把稳定燃点部件集成为一体的非定向集成式LED灯丝灯。

Integrated LED Filament Lamps for general lighting — Performance requirements

T/ZALI 0005-2019 普通照明用LED灯丝 规格分类

本标准规定了普通照明用LED灯丝（以下简称“灯丝”）的分类和规格以及相关要求。 本标准适用于符合T/ZALI 0006—2019要求、在家庭和类似场合作为普通照明用、把稳定燃点部件集成为一体的LED灯丝灯用的灯丝。

Classification of LED Filament for general lighting

T/ZALI 0008-2019 双端集成式LED灯 性能要求

规定了普通照明用、带G5或G13灯头、用于带G5或G13灯座不带镇流器的灯具中的双端集成式LED灯的术语和定义、分类与命名、要求、试验方法和检验规则。

Double-capped integrated LED lamps — Performance requirements

T/ZALI 0007-2019 双端集成式LED灯 安全要求

本标准规定了带G5和G13灯头的双端集成式LED灯的安全要求和互换性要求，以及检验其符合性的试验方法和检验条件。  

Double-capped integrated LED lamps — Safety specifications

T/SZSA 024.2-2019 室内健康照明设计规范 第2部分：家居照明

前言 引言 1 范围  2 规范性引用文件  3 术语和定义  4 基本规定 5 照明数量和质量 6 家居照明中全光谱的光谱参数要求 7 测试方法 8 家居照明中全光谱的光谱参数要求 本标准规定了室内健康照明设计-家居照明的限值。 本部分适用于作为家居照明的设计技术依据。 本部分不适用于广场、体育场馆、大型文艺演出场馆等室外场合照明质量的设计和评价。

Design Code for Indoor Healthy Lighting Part 2: Home Lighting

T/CEEIA 318-2018 爆炸性环境用照明灯具技术规范

本技术规范规定了爆炸性环境用照明灯具（以下简称灯具）的技术要求和试验方法，其中包括通用安全要求、防爆性能要求和光电性能要求。 本技术规范适用于电源电压不超过1000V，以LED光源（包括LED模块）、白炽灯、卤钨灯、荧光灯泡（包括紧凑型荧光灯）、高压汞灯、金属卤化物灯和高压钠灯(高压气体放电灯)为光源的灯具。煤矿井下用照明灯具可参照使用。 本技术规范不适用于火炸药环境使用的灯具。

General rules of explosion-proof techniques of luminaries for explosive atmospheres

IEC TR 63139:2018 解释TC 34标准中工作电压、电路间绝缘和PELV使用的数学加法

This document is related to the insulation coordination in TC 34 standards and provides explanations on mathematical addition of working voltages@ insulation between circuits@ use of protective extra low voltage (PELV) and insulation between LV supply and control line conductors in order to cover new technologies associated with the use of LED light sources and controllable products. It describes in which way the addition of supply voltages and working voltages can be arranged for an assessment of the electrical insulation requirements (e.g. creepage distances and clearances) in a system if a first failure occurs. Furthermore the actual failure scenarios given in IEC 60598-1:2014 and IEC 60598- 1:2014/AMD1:2017@ Annex X and IEC 61347-1:2015@ Clause 15 are explained in greater detail and the rationale behind the protective requirement for each situation is given (e.g. possible LV primary to ELV secondary does not lead to an overburden of the insulation in the second circuit). This document also describes the possibility to increase immunity and reliability of electronic circuits@ used in combination with LEDs@ with the use of PELV and the associated safety consequences for this system. The insulation between LV supply and control line conductors is also important and this document explains why this is an essential safety consideration for a complete installation system.

Explanation of the mathematical addition of working voltages, insulation between circuits and use of PELV in TC 34 standards

T/ZZB 0447-2018 户外景观照明用LED点光源

本标准规定了户外景观照明用LED点光源的术语和定义、基本要求、通讯控制要求、分类与命名、技术要求、试验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于输入电压DC≤36 V户外景观照明用LED点光源（以下简称“LED点光源”）。

LED pixel light source for outdoor landscape lighting

IEC 62612:2013/AMD2:2018 电源电压>50V的一般照明设备用自镇流LED灯.性能要求

Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements

IEC 62612:2013+AMD1:2015+AMD2:2018 CSV 电源电压>50V的一般照明设备用自镇流LED灯.性能要求

Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements

IEC TR 63158:2018/COR1:2018 一般照明用设备 照明设备频闪效应的客观试验方法

Equipment for general lighting purposes - Objective test method for stroboscopic effects of lighting equipment

IEC TR 63130:2018 金属卤化物灯的调光和热重燃

This document describes the current state of experts?? opinions on the standardization of metal halide lamps to cover the relevant parameters for hot restrike and for dimming in combination with low frequency square wave ballasts. It provides guidelines for supplementing or modifying IEC 61167 in order that these conditions are covered.

Dimming and hot restrike of metal halide lamps

IEC TR 63158:2018 一般照明设备.照明设备频闪效应的客观试验方法

This document describes an objective stroboscopic effect visibility (SVM) meter@ which can be applied for performance testing of lighting equipment under different operational conditions. The stroboscopic effects considered in this document are limited to the objective assessment by a human observer of visible stroboscopic effects of temporal light modulation of lighting equipment in general indoor applications@ with typical indoor light levels (> 100 lx) and with moderate movements of an observer or nearby handled object (< 4 m/s). Details on restriction of the applicability of the stroboscopic effect visibility measure is given in Clause A.1. For assessing unwanted stroboscopic effects in other applications@ such as the misperception of rapidly rotating or moving machinery in an industrial environment for example@ other metrics and methods can be required. The object of this document is to establish a common and objective reference for evaluating the performance of lighting equipment in terms of stroboscopic effect. Temporal changes in the colour of the light (chromatic effects) are not considered in this test. This document describes the methodology for SVM and does not define any limits. The objective method and procedure described in this document are based on CIE TN 006:2016 on temporal light artefacts (TLAs). The method described in this document can be applied to objectively assess the stroboscopic effect of lighting equipment that is powered from any type of source@ AC mains@ DC mains@ battery fed or fed through an external dimmer.

Equipment for general lighting purposes - Objective test method for stroboscopic effects of lighting equipment