29.160 旋转电机 标准查询与下载
共找到 316 条与 旋转电机 相关的标准，共 22 页
Rotating electrical machines - Part 27-2: On-line partial discharge measurements on the stator winding insulation of rotating electrical machines
- ICS
- 29.160
- CCS
- K20
- 发布
- 2012-03-22
- 实施
本标准规定了额定功率3 125 kVA（50 Hz和60 Hz）及以下船用三相同步发电机（以下简称发电机）及其励磁装置的技术要求、试验方法、检验规则、标志和包装等内容。 本标准适用于由内燃机驱动，用作船舶及移动式和固定式近海装置电站的发电机及其励磁装置。 对由汽轮机驱动的发电机、轴带发电机和额定功率大于3 125 kVA的发电机，亦可参照采用本标准。
Specification for three-phase synchronous generator in ships
- ICS
- 29.160
- CCS
- K26
- 发布
- 2011-12-20
- 实施
- 2012-04-01
本标准规定了单相电动机起动用离心开关的术语和定义、型号、参数和尺寸、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于额定电压为交流 220 V及以下、频率为50/60 Hz、功率为5000 W及以下的单相电动机起动用离心开关。
Specification for centrifugal starting switch use of single-phase motor
- ICS
- 29.160
- CCS
- K22
- 发布
- 2011-12-20
- 实施
- 2012-04-01
Rotating electrical machines -- Part 16-1: Excitation systems for synchronous machines - Definitions (IEC 60034-16-1:2011)
- ICS
- 29.160
- CCS
- 发布
- 2011-11-30
- 实施
- 2011-11-30
Rotating electrical machines -- Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines (IEC/TS 60034-27:2006)
- ICS
- 29.160
- CCS
- 发布
- 2011-04-15
- 实施
- 2011-04-15
Rotating electrical machines -- Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance (IEC 60034-18-32:2010)
- ICS
- 29.160
- CCS
- 发布
- 2011-04-15
- 实施
- 2011-04-15
IEC/TS 60034-18-33:2010 describes procedures for evaluation of insulation systems by endurance testing where thermal and electrical stresses are applied simultaneously. The procedures are intended for insulation systems used in a.c. electrical machines using form-wound windings. The test procedures provide a comparison of performance between reference and candidate systems at combinations of voltage and temperature which have been used separately to assess quality in the past and which are chosen to produce failures within a suitable timescale and at stresses within practical limits. The outcome of the test on the candidate insulation system will indicate whether it is better or worse than the reference system with proven service experience. The main changes of this new edition with respect to the previous one are as follows: - the requirement to investigate the nature of interactions between thermal and electrical stresses has been abandoned; - the use of single stress acceleration factors has been removed; - the selection of stress levels has been adjusted and the temperatures are now related to the thermal class temperature of the insulation system; - the introduction of end-point criteria; - a simplified method to display results.
Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
- ICS
- 29.160
- CCS
- 发布
- 2011-03-25
- 实施
- 2011-08-21 (7)
IEC/TS 60034-24:2009 is applicable to the on-line detection and diagnosis of failures at the active parts of multi-phase rotating electrical machines (induction and synchronous machines) and of bearing currents. The failure analysis includes - inter-turn faults; - phase-to-phase short-circuits; - double earth faults and single earth faults of motors with earth connection of the star-point; - static and dynamic eccentricities; - cage imperfection or defects (e.g. broken bars or end-rings); - bearing currents.
Rotating electrical machines - Part 24: Online detection and diagnosis of potential failures at the active parts of rotating electrical machines and of bearing currents - Application guide
- ICS
- 29.160
- CCS
- 发布
- 2011-02-25
- 实施
- 2011-07-25 (7)
IEC/TS 60034-31:2010 provides a guideline of technical aspects for the application of energy-efficient, three-phase, electric motors. It not only applies to motor manufacturers, original equipment manufacturers, end users, regulators and legislators but to all other interested parties. Is applicable to all electrical machines covered by IEC 60034-30.
Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
- ICS
- 29.160
- CCS
- 发布
- 2011-02-25
- 实施
- 2011-08-21 (7)
Rotating electrical machines -- Part 1: Rating and performance (IEC 60034-1:2010, modified)
- ICS
- 29.160
- CCS
- 发布
- 2011-01-31
- 实施
- 2011-01-31
Rotating electrical machines -- Part 1: Rating and performance (IEC 60034-1:2010, modified)
- ICS
- 29.160
- CCS
- 发布
- 2011-01-31
- 实施
- 2011-01-31
Rotating electrical machines -- Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
- ICS
- 29.160
- CCS
- K20
- 发布
- 2011-01-20
- 实施
本标准规定了以直联或法兰连接内燃机的发动机分类与命名、型式、基本参数、结构及尺寸、技术要求、试验方法、检验规则和标志、包装、运输、贮存等。本标准适用于额定功率不大于3kw的小型单相/三相二极同步发电机。
Technical conditions for small synchronous generators
- ICS
- 29.160
- CCS
- K 21
- 发布
- 2011-01-20
- 实施
- 2011-04-01
Rotating electrical machines - Part 11: Thermal protection
- ICS
- 29.160
- CCS
- 发布
- 2011
- 实施
Rotating electrical machines -- Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1 (IEC 60034-2-2:2010)
- ICS
- 29.160
- CCS
- 发布
- 2010-11-15
- 实施
- 2010-11-15
IEC 60034-29 provides various indirect load tests, the purpose of which is to determine the temperature rise of rotating electrical machines, including a.c. induction machines, a.c. synchronous machines and d.c. machines. The test methods in some cases provide, in addition, means of measuring or estimating other parameters such as losses and vibration. Applies to machines covered by IEC 60034-1 when they cannot be loaded to a specific condition. Is applicable to both motors and generators.
Rotating electrical machines - Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise
- ICS
- 29.160
- CCS
- 发布
- 2010-10-31
- 实施
Rotating electrical machines -- Part 18-1: Functional evaluation of insulation systems - General guidelines (IEC 60034-18-1:2010)
- ICS
- 29.160
- CCS
- 发布
- 2010-10-15
- 实施
- 2010-10-15
This part of IEC 60034-18 describes test procedures for the evaluation of electrical endurance of insulation systems for use in a.c. or d.c. rotating electrical machines using form-wound windings. The test procedures are comparative in nature, such that the performance of a candidate insulation system is compared to that of a reference insulation system with proven service experience. The test procedures are principally directed at the insulation systems in air-cooled machines but may also be used for evaluating parts of the insulation systems in hydrogen cooled machines. Note that the qualification procedures of inverter duty insulation systems for form-wound windings can be found in IEC 60034-18-42.
Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance
- ICS
- 29.160
- CCS
- K20
- 发布
- 2010-10
- 实施
- 2010-10
This part of IEC 60034-18 describes procedures for evaluation of insulation systems by endurance testing where thermal and electrical stresses are applied simultaneously. The procedures are intended for insulation systems used, or proposed to be used, in a.c. electrical machines using form-wound windings. The test procedures provide a comparison of performance between reference and candidate systems at combinations of voltage and temperature which have been used separately to assess quality in the past and which are chosen to produce failures within a suitable timescale and at stresses within practical limits. The outcome of the test on the candidate insulation system will indicate whether it is better or worse than the reference system with proven service experience but will not enable a lifetime in service to be calculated. The evaluation described in this technical specification does not include stress grading. The test procedures in this technical specification are not intended to establish the interaction between thermal and electrical stress in the ageing process nor endurance lines. If additional information is required on this interaction or in order to achieve endurance lines, it is necessary to undertake further tests in which electrical ageing is carried out at constant temperature and different voltages (IEC 60034-18-32) and thermal ageing is performed at different temperatures and constant voltage.
Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
- ICS
- 29.160
- CCS
- K20
- 发布
- 2010-07
- 实施
This part of IEC 60034 provides a guideline of technical aspects for the application of energyefficient, three-phase, electric motors. It not only applies to motor manufacturers, OEMs (original equipment manufacturers), end users, regulators and legislators but to all other interested parties. This technical specification is applicable to all electrical machines covered by IEC 60034-30. Most of the information however is also relevant for cage-induction machines with output powers exceeding 375 kW.
Rotating electrical machines – Part 31: Selection of energy-efficient motors including variable speed applications – Application guide
- ICS
- 29.160
- CCS
- K20
- 发布
- 2010-04
- 实施
