29.160.40 发电机组 标准查询与下载

UL 2201 BULLETINS-2003

This standard specifies the outline of investigation for portable engine-generator assemblies

12/19/2003 (10p); 8/15/2003 (122p)

ARMY MIL-DTL-53133 C SUPP 1-2002 一般规格的5至60万千瓦交流电.柴油机驱动的.静音的战术的.装在滑动底座的发电机组(代替使用ARMY MIL-DTL-0053133 B NOTICE 1)

This supplement forms a part of MIL-DTL-53133C, dated 15 April 2002.

GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR [Use In Lieu Of: ARMY MIL-DTL-0053133 B NOTICE 1]

ARMY MIL-DTL-53133 C-2002 一般规格的5至60万千瓦交流电.柴油机驱动的.静音的战术的.装在滑动底座的发电机组

This commercial item description covers brown kraft paper used for general wrapping applications.

GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR

JB/T 10304-2001 工频汽油发电机组技术条件

　　本标准规定了往复式内燃(RIC)发动机、交流(a.c.)发电机、控制装置和辅助设备组成的工频汽油发电机组的技术要求、试验方法、检验规则、标志、包装及贮运要求。 　　本标准适用于额定频率为50Hz、发动机为汽油机的发电机组。 　　60Hz的机组可参照使用。

Gasoline generating sets of 50Hz technical conditions for

JB/T 10303-2001 工频柴油发电机组技术条件

　　本标准规定了往复式内燃(RIC)发动机、交流(a.c.)发电机、控制装置和辅助设备组成的工频柴油发电机组的技术要求、试验方法、检验规则、标志、包装及贮运要求。 　　本标准适用于0.5kV～3150kW、额定频率为50Hz、发动机为柴油机的发电机组。 　　60Hz的机组可参照使用。

Diesel generating sets of 50Hz technical conditions for

BS EN 62040-3:2001 非干扰电力系统(UPS).规定性能和试验要求的方法

This standard applies to electronic indirect a.c. converter systems with electrical energy storage means in the d.c. link. The primary function of the uninterruptible power system (UPS) covered by this standard is to ensure continuity of an alternating power source. The uninterruptible power system may also serve to improve the quality of the power source by keeping it within specified characteristics. A variety of uninterruptible power systems have been developed to meet consumers' requirements for continuity and quality of power for different types of loads over a wide range of power, from less than 100 W to several megawatts. Refer to annexes A and B for information on some of the types available. This standard applies to electronic uninterruptible power systems (UPS): a) delivering single- or three-phase fixed frequency a.c. output voltage; b) with energy storage device in the d.c. link if not otherwise specified; c) with rated voltage not exceeding 1 000 V a.c; d) movable, stationary and/or fixed equipment. This standard also includes the method of specifying all power switches that form integral parts of a UPS and are associated with its output. Included are interrupters, bypass switches, isolating switches, load transfer switches and tie switches. These switches interact with other functional units of the UPS to maintain continuity of load power. This standard does not refer to conventional mains distribution boards, rectifier input switches or d.c. switches (for example for batteries, rectifier output or inverter input, etc.), or UPS based on rotating machines. NOTE 1 - This standard recognizes that the major market usage with the UPS ratings within its scope is in conjunction with information technology equipment. Under current technology, the majority of UPS load equipment employs power supplies which present a non-linear load to the UPS and can be tolerant of non-sinusoidal voltage waveforms for a limited time duration. UPS output ratings are specified to be compatible with non-linear loading and linear loading, subject to manufacturers' declaration if different. References within this standard to linear loading are retained for test method reasons, or validation of manufacturers' additional declaration. NOTE 2 - For use of UPS with a non-sinusoidal output voltage waveform, beyond the stored-energy time recommended in this standard, the agreement of the load equipment manufacturer should be sought. NOTE 3 - For UPS output frequencies other than 50 Hz or 60 Hz, performance specification is subject to agreement between manufacturer and purchaser. This standard is intended to define a complete uninterruptible power system in terms of its performance and not individual UPS functional units. The individual UPS functional units are dealt with in the IEC publications referred to in the bibliography given in annex I, which apply in so far as they are not in contradiction with this standard.

Uninterruptible power systems (UPS) - Method of specifying the performance and test requirements

ARMY MIL-STD-1332 B NOTICE 2-2001 国防部移动电力发电机组的分类的公用事业用语.准确的最佳的战术定义

MIL-STD-1332B, dated 13 March 1973, is hereby reactivated and may be used for either new or existing design acquisitions.

DEFINITIONS OF TACTICAL, PRIME, PRECISE, AND UTILITY TERMINOLOGIES FOR CLASSIFICATION OF THE DOD MOBILE ELECTRIC POWER ENGINE GENERATOR SET FAMILY

LST EN 61204-2000 低压电源设备，直流输出 性能特征和安全要求（IEC 61204:1993，已修改）

Low-voltage power supply devices, d.c. output. Performance characteristics and safety requirements (IEC 61204:1993, modified)

DL/T 717-2000 汽轮发电机组转子中心孔检验技术导则

Technical guide for the nondestructive testing of turbine-generator rotor bores

JB/T 8186-1999 工频柴油发电机组.额定功率、电压及转速

　　本标准规定了用柴油机驱动工频交流发电机的柴油发电机组的额定功率、额定电压和额定转速等级。 本标准适用于频率为50Hz，单相机组功率因数为0.9(滞后)或1.0，三相机组功率因数为0.8(滞后)的交流单相和三相的机组。 60Hz机组可参照使用。

Rated output、voltage and speed for diesel generating sets of 50 Hz

JB/T 9583.1-1999 气体燃料发电机组.通用技术条件

　　本标准规定了气体燃料发电机组的技术要求、试验方法、检验规则、标志、包装及贮运等要求。 本标准适用于0.5～800kW燃烧天然气、煤气、沼气等气体及其与柴油混合燃烧的内燃机驱动交流工频发电机的发电机组。

General technical conditions for gas fuel generating sets

JB/T 1403-1999 移动电站.产品名称和型号编制规则

　　本标准规定了由内燃机驱动交流工频(50Hz)、中频(400Hz)、双频(50Hz、400Hz)和直流发电机的移动电站(含汽车电站、挂车电站、移动式发电机组)产品名称和型号的编制规则。 本标准适用于0.5～3150kW的电站。 60Hz电站可参照使用。

Compilation rules for title and model of movable power plant

JB/T 2729-1999 交流移动电站用三相四极插头插座

　　本标准规定了用内燃机驱动交流工频(50Hz)、中频(400Hz)、双频(50Hz、400Hz)发电机的内燃机电站(含汽车电站、挂车电站、发电机组，以下简称电站)用三相四极插头插座的型式、技术要求、试验方法、检验规则等。 本标准适用于额定电压不高于400V，额定频率为50Hz和400Hz的电站用三相四极插头插座。60Hz电站用插头插座可参照使用。

3 phases 4 wires plug & socket for AC movable power plant

JB/T 9583.2-1999 气体燃料发电机组.额定功率、电压及转速

　　本标准规定了燃烧气体燃料的工频交流发电机组的额定功率、额定电压和额定转速的等级。 本标准适用于频率为50Hz，单相机组功率因数为0.9(滞后)或1.0、三相机组功率因数为0.8(滞后)，燃烧天然气、沼气、发生炉煤气、城市煤气的交流单相机组。 60Hz机组可参照使用。

Rated output, voltage and speed for gas fuel generating sets

IEC 62040-3:1999 不间断电源系统(UPS) 第3部分:规定性能的方法和试验要求

This standard applies to electronic indirect a.c. converter systems with electrical energy storage means in the d.c. link. The primary function of the uninterruptible power system (UPS) covered by this standard is to ensure continuity of an alternating power source. The uninterruptible power system may also serve to improve the quality of the power source by keeping it within specified characteristics. A variety of uninterruptible power systems have been developed to meet consumers' requirements for continuity and quality of power for different types of loads over a wide range of power, from less than 100 W to several megawatts. Refer to annexes A and B for information on some of the types available. This standard applies to electronic uninterruptible power systems (UPS): a) delivering single- or three-phase fixed frequency a.c. output voltage; b) with energy storage device in the d.c. link if not otherwise specified; c) with rated voltage not exceeding 1 000 V a.c.; d) movable, stationary and/or fixed equipment. This standard also includes the method of specifying all power switches that form integral parts of a UPS and are associated with its output. Included are interrupters, bypass switches, isolating switches, load transfer switches and tie switches. These switches interact with other functional units of the UPS to maintain continuity of load power. This standard does not refer to conventional mains distribution boards, rectifier input switches or d.c. switches (for example for batteries, rectifier output or inverter input, etc.), or UPS based on rotating machines. NOTE 1 - This standard recognizes that the major market usage with the UPS ratings within its scope is in conjunction with information technology equipment. Under current technology, the majority of UPS load equipment employs power supplies which present a non-linear load to the UPS and can be tolerant of non-sinusoidal voltage waveforms for a limited time duration. UPS output ratings are specified to be compatible with non-linear loading and linear loading, subject to manufacturers' declaration if different. References within this standard to linear loading are retained for test method reasons, or validation of manufacturers' additional declaration. NOTE 2 - For use of UPS with a non-sinusoidal output voltage waveform, beyond the stored-energy time recommended in this standard, the agreement of the load equipment manufacturer should be sought. NOTE 3 - For UPS output frequencies other than 50 Hz or 60 Hz, performance specification is subject to agreement between manufacturer and purchaser. This standard is intended to define a complete uninterruptible power system in terms of its performance and not individual UPS functional units. The individual UPS functional units are dealt with in the IEC publications referred to in the bibliography given in annex I, which apply in so far as they are not in contradiction with this standard.

Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements

DL/T 651-1998 氢冷发电机氢气湿度的技术要求

Requirements for hydrogen humidity of generators using hydrogen as a coolant

BS 7698-12:1998 往复式内燃机驱动交流发电设备.安全装置的应急供电

This part of ISO 8528 applies to generating sets driven by reciprocating internal-combustion (RIC) engines for emergency power supply to safety services. It applies, for example, to safety equipments in hospitals, high-rise buildings, public gathering places etc. This part of ISO 8528 establishes the special requirements for the performance, design and maintenance of power generators used in the applications referred to above and taking into account the provisions of ISO 8528-1 to ISO 8528-6 and ISO 8528-10.

Reciprocating internal combustion engine driven alternating current generating sets - Emergency power supply to safety devices

KS V 8863-1997(2012) 海洋振荡装置的电源管理系统

Power management system for marine generating plants

ISO 8528-12:1997 往复式内燃交流发电机组 第12部分:应急发电设备

This part of ISO 8528 applies to generating sets driven by reciprocating internal-combustion (RIC) engines for emergency power supply to safety services. It applies, for example, to safety equipments in hospitals, high-rise buildings, public gathering places etc. This part of ISO 8528 establishes the special requirements for the performance, design and maintenance of power generators used in the applications referred to above and taking into account the provisions of ISO 8528-1 to ISO 8528-6 and ISO 8528-10.

Reciprocating internal combustion engine driven alternating current generating sets - Part 12: Emergency power supply to safety services

BS 7698-7:1996 往复式内燃机驱动的交流发电机组.规格和设计的技术声明

This part of ISO 8528 specifies the requirements and parameters for the specification and design of a reciprocating internal combustion (RIC) engine driven generating set, with reference to the definitions given in ISO 8528-1 to ISO 8528-6. It applies to alternating current (a.c.) generating sets driven by RIC engines for land and marine use, ex-cluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (for example, essential hospital supplies, high-rise buildings, etc.) sup-plementary requirements may be necessary. The provisions of this part of ISO 8528 should be regarded as a basis. For other reciprocating-type prime movers (e.g. sew-age gas engines, steam engines), the provisions of this part of ISO 8528 should be used as a basis.

Reciprocating internal combustion engine driven alternating current generating sets - Technical declarations for specification and design