31.060.30 纸介电容器和塑料膜电容器 标准查询与下载

LST EN 60384-2-2012 电子设备用固定电容器 第2部分：分规范 金属化聚对苯二甲酸乙二醇酯薄膜介质直流固定电容器（IEC 60384-2:2011）

Fixed capacitors for use in electronic equipment -- Part 2: Sectional specification - Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors (IEC 60384-2:2011)

LST EN 60384-13-2012 电子设备用固定电容器 第13部分：分规范 固定聚丙烯薄膜介质金属箔直流电容器（IEC 60384-13:2011）

Fixed capacitors for use in electronic equipment -- Part 13: Sectional specification - Fixed polypropylene film dielectric metal foil d.c. capacitors (IEC 60384-13:2011)

BS EN 60384-2:2012 电子设备用固定电容器.分规范.固定式金属处理的聚对苯二甲酸乙二醇酯薄膜非传导性直流电容器

Fixed capacitors for use in electronic equipment. Sectional specification. Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors

BS EN 60384-13:2012 电子设备用固定电容器.分规范.聚丙烯膜介质金属箔直流固定电容器

Fixed capacitors for use in electronic equipment. Sectional specification/ Fixed polypropylene film dielectric metal foil d.c. capacitors

EN 60384-13:2012 电子设备用固定电容器 第13部分：分规范 固定聚丙烯薄膜介电金属箔直流电容器

IEC 60384-13:2011 applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this standard are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. This fourth edition cancels and replaces the third edition published in 2006 and contains the following significant technical changes with respect to the previous edition. - Table 3, Sampling plan together with numbers of permissible non-conformance for qualification approval test, has been adjusted. - Table 5, Lot-by-lot inspection, has been changed, highlighting assessment level EZ only. - Table 6, Periodic inspection, has been changed, highlighting assessment level EZ only.

Fixed capacitors for use in electronic equipment - Part 13: Sectional specification - Fixed polypropylene film dielectric metal foil d.c. capacitors

IEC 60384-13:2011 电子设备用固定电容器.第13部分:分规范:金属箔式聚苯乙烯膜介质直流固定电容器

This part of IEC 60384 applies to fixed direct current capacitors@ using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this standard are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included@ but are covered by IEC 60384-14.

Fixed capacitors for use in electronic equipment - Part 13: Sectional specification - Fixed polypropylene film dielectric metal foil d.c. capacitors

IEC 60384-2:2011 电子设备用固定电容器.第2部分:分规范.金属化聚乙烯对苯二甲酸酯膜介质直流固定电容器

"This part of IEC 60384 applies to fixed capacitors for direct current@ with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment. These capacitors may have ""self-healing properties"" depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. Two performance grades of capacitors are covered@ Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression and surface mount fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors are not included@ but are covered by IEC 60384-14 and IEC 60384-19 respectively."

Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors

KS C IEC 60384-2:2010 电子设备用固定电容器.第2部分:分规范:金属化聚乙烯对苯二甲酸乙二酸酯薄膜介质直流固定电容器

이 표준은 전자 장비에 사용되는 금속화 전극 및 폴리에틸렌-테레프탈레이트 유전체를 갖는 직

Fixed capacitors for use in electronic equipment-Part 2:Sectional specification:Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors

JIS C 5101-3-1:2010 电子设备用固定电容器.第3-1部分:空白详细规范.带有二氧化锰固体电解质的表面安装固定式钽电解电容器.评估标准EZ

This Japanese Industrial Standard has been prepared based on the second edition of IEC 60384-3-1 published in 2006 without modifying the technical contents.

Fixed capacitors for use in electronic equipment -- Part 3-1: Blank detail specification -- Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte -- Assessment level EZ

JIS C 5101-3:2010 电子设备用固定电容器.第3部分:分规范.带有二氧化锰固体电解质的表面安装固定式钽电解电容器.

Fixed capacitors for use in electronic equipment -- Part 3: Sectional specification -- Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte

SNI IEC 60252-1:2010 交流电动机的电容器. 第1部分:总则. 性能、试验和额定. 安全要求. 安装和操作指南

AC motor capsitors - part 1: general -Performance testing and rating - Safety requirements - guide for installation and operation

TIS 1902-2009 电子设备用固定电容器.第3部分:分规范.带二氧化锰固体电解质的表面安装电解质钽固定电容器

Fixed capacitors for use in electronic equipment.part 3: sectional specification: surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte

DIN EN 60384-13-1 Berichtigung 1:2009 电子设备用固定电容器.第13-1部分:空白详细规范.聚丙烯膜介质金属箔直流固定电容器.评定级别 E(IEC 60384-13-1:2006),德文版本EN 60384-13-1:2006,勘误表

Fixed capacitors for use in electronic equipment - Part 13-1: Blank detail specification - Fixed polypropylene film dielectric metal foil d.c. capacitors - Assessment level E (IEC 60384-13-1:2006); German version EN 60384-13-1:2006, Corrigendum to DIN EN

LST EN 60384-3-1-2007/AC-2009 电子设备用固定电容器 第 3-1 部分：空白详细规范：采用二氧化锰固体电解质的表面贴装固定钽电解电容器 评估等级 EZ（IEC 60384-3-1:2006）

Fixed capacitors for use in electronic equipment - Part 3-1: Blank detail specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte - Assessment level EZ (IEC 60384-3-1:2006)

LST EN 60384-13-1-2006/AC-2009 电子设备用固定电容器 第 13-1 部分：空白详细规范 固定聚丙烯薄膜介电金属箔直流电容器 评估等级 E 和 EZ（IEC 60384-13-1:2006）

Fixed capacitors for use in electronic equipment - Part 13-1: Blank detail specification - Fixed polypropylene film dielectric metal foil d.c. capacitors - Assessment level E and EZ (IEC 60384-13-1:2006)

BS EN 60384-20:2009 电子设备用固定电容器 分规范 金属化聚苯撑硫薄膜电介质表面安装直流（d c ）固定电容器

Fixed capacitors for use in electronic equipment. Sectional specification. Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors

JIS C 5101-17:2009 电子设备用固定电容器.第17部分:分规范:金属化聚丙烯膜介质直流和脉冲固定电容器

This Standard is a sectional specification associated with the generic specification JIS C 5101-1 and applies to fixed metallized polypropylene film dielectric a.c. and pulse capacitors for use in electronic equipment (hereafter referred to as "capacitors"). It covers fixed capacitors with metallized electrodes and polypropylene dielectric for use in electronic equipment. NOTE 1 Capacitors which have mixed foil and metallized electrodes are also within the scope of this Standard. These capacitors may have "self-healing" properties depending on conditions of use. Capacitors covered by this Standard are mainly intended for use with alternating voltage and/or for pulse applications. The maximum reactive power applicable is 10 000 var and the maximum peak voltage is 3 000 V. Capacitors for reactive power exceeding 500 var and to which a maximum peak voltage of 2 500 V at 50 Hz can be applied are not covered by this Standard, except when they are the highest part of a range of reactive power mainly situated below 500 var at 50 Hz. This Standard is not intended to cover capacitance values higher than 20 μF. Two performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression are not included, but are covered by JIS C 5101-14. Capacitors for electrical shock hazard protection (covered by IEC 60065) and fluorescent lamp and motor capacitors are also excluded. NOTE 2 The International Standard corresponding to this Standard is as follows. IEC 60384-17 : 2005 Fixed capacitors for use in electronic equipment— Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors (IDT) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21.

Fixed capacitors for use in electronic equipment -- Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors

JIS C 5101-17-1:2009 电子设备用固定电容器.第17-1部分:空白详细规范.金属化聚丙烯膜介质直流和脉冲固定电容器.评定等级E和EZ

This Standard is a blank detail specification associated with the sectional specification JIS C 5101-17 and specifies fixed metallized polypropylene film dielectric a.c. and pulse capacitors (hereafter referred to as "capacitors") assessment levels E and EZ. NOTE : The International Standard corresponding to this Standard is as follows. IEC 60384-17-1:2005 Fixed capacitors for use in electronic equipment— Part 17-1: Blank detail specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors—Assessment levels E and EZ (IDT) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21.

Fixed capacitors for use in electronic equipment -- Part 17-1: Blank detail specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors -- Assessment levels E and EZ

JIS C 5101-2:2009 电子设备用固定电容器.第2部分:分规范:金属化聚乙烯对苯二甲酸酯膜介质直流固定电容器

This Standard is a sectional specification associated with the generic specification JIS C 5101-1 and applies to fixed capacitors (hereafter referred to as "capacitors") for direct current, with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment. These capacitors may have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. Two performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression and surface mount fixed met- allized polyethylene-terephthalate film dielectric d.c. capacitors are not included, but are covered by JIS C 5101-14 and IEC 60384-19, respectively. NOTE : The International Standard corresponding to this Standard is as follows. IEC 60384-2:2005 Fixed capacitors for use in electronic equipment-- Part 2: Sectional specification: Fixed metallized polyethylene-terephtha- late film dielectric d.c. capacitors (IDT) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21.

Fixed capacitors for use in electronic equipment -- Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors

JIS C 5101-16-1:2009 电子设备用固定电容器.第16-1部分:空白详细规范:金属化聚丙烯膜介质直流固定电容器.评定等级E和EZ

This Standard is a blank detail specification associated with the sectional specification JIS C 5101-16 and specifies fixed metallized polypropylene film dielectric d.c. capacitors (hereafter referred to as "capacitors") assessment levels E and EZ. NOTE : The International Standard corresponding to this Standard is as follows. IEC 60384-16-1: 2005 Fixed capacitors for use in electronic equipment— Part 16-1: Blank detail specification—Fixed metallized polypropylene film dielectric d.c. capacitors—Assessment levels E and EZ (IDT) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ IEC Guide 21.

Fixed capacitors for use in electronic equipment -- Part 16-1: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors -- Assessment levels E and EZ