33.100.10 发射 标准查询与下载

LST EN IEC 61851-21-2:2021 电动汽车传导充电系统 第 21-2 部分：电动汽车对交流/直流电源传导连接的要求 非车载电动汽车充电系统的 EMC 要求（IEC 61851-21-2:2018）

Electric vehicle conductive charging system - Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply - EMC requirements for off board electric vehicle charging systems (IEC 61851-21-2:2018)

GSO IEC TR 61000-4-37:2021 电磁兼容性 (EMC) 谐波发射合规性测试系统的校准和验证协议

IEC TR 61000-4-37:2016 outlines a typical test procedure for harmonic analysis in systems comprising tests apparatus designed to comply with IEC 61000-4-7, and products designed to comply with IEC 61000-3-2 and/or IEC 61000-3-12. The test procedure is intended to provide a systematic guidance suitable for use by manufacturers, end users, independent test laboratories and other bodies, for the purpose of determining the applicable compliance status within a wide range of harmonic current emissions. It is not intended as a replacement for type testing of harmonic analyzers, nor does it check all of the parameters specified in IEC 61000-4-7, IEC 61000-3-2, and IEC 61000-3-12. This publication contains attached files in the form of an xls document and a user guide. These files are intended to be used as a complement and do not form an integral part of the standard.

Electromagnetic compatibility (EMC) - Calibration and verification protocol for harmonic emission compliance test systems

GSO CISPR TR 31:2021 无线电业务特征数据库

CISPR/TR 31:2012 covers the rationale behind the actual database covering the characteristics of radio services. The objective of the database is to register those characteristics which are relevant for derivation and specification of limits for disturbance emissions from electric and/or electronic equipment, systems and installations. Committees responsible for generic and/or product emission EMC standards should use this information together with CISPR 23. This second edition includes the replacement of CISPR 23 as reference standard for the determination of limits by CISPR 16-4-4:2007 on "model for the calculation of limits for the protection of radio services".

Database on the characteristics of radio services

GSO IEC 61000-6-3:2021 电磁兼容性 (EMC) 第6-3部分：通用标准 住宅环境中设备的发射标准

IEC 61000-6-3:2020 is a generic EMC emission standard applicable only if no relevant dedicated product or product family EMC emission standard has been published. This part of IEC 61000 for emission requirements applies to electrical and electronic equipment intended for use at residential (see 3.1.14) locations. This part of IEC 61000 also applies to electrical and electronic equipment intended for use at other locations that do not fall within the scope of IEC 61000-6-8 or IEC 61000-6-4. The intention is that all equipment used in the residential, commercial and light-industrial environments are covered by IEC 61000-6-3 or IEC 61000-6-8. If there is any doubt the requirements in IEC 61000-6-3 apply. The conducted and radiated emission requirements in the frequency range up to 400 GHz are considered essential and have been selected to provide an adequate level of protection of radio reception in the defined electromagnetic environment. Not all disturbance phenomena have been included for testing purposes but only those considered relevant for the equipment intended to operate within the locations included within this document. The emission requirements in this document are not intended to be applicable to the intentional transmissions and their harmonics from a radio transmitter as defined by the ITU. This third edition cancels and replaces the second edition published in 2006 and its Amendment 1:2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alternative method for measuring conducted emissions on DC ports; b) limits and requirements applicable only to equipment intended to be used in residential locations; c) more stringent limits for DC power ports. NOTE 1 Safety considerations are not covered by this document. NOTE 2 In special cases, situations will arise where the levels specified in this document will not offer adequate protection; for example where a sensitive receiver is used in close proximity to an equipment. In these instances, special mitigation measures can be employed. NOTE 3 Disturbances generated in fault conditions of equipment are not covered by this document. NOTE 4 As the requirements in this document are more stringent or equivalent to those requirements in IEC 61000-6-4 and IEC 61000-6-8, equipment fulfilling the requirements of this document comply with the requirements of IEC 61000-6-4 and IEC 61000-6-8.

Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential environments

GSO CISPR TR 30-1:2021 电磁辐射测试方法 第1部分：单端和双端荧光灯电子控制装置

CISPR/TR 30-1:2012(E), which is a technical report, details, with the aid of reference luminaires, an independent method by which the radio disturbance characteristics of electronic control gear for fluorescent lamp luminaires with protection classes I and/or II may be compared against the requirements of CISPR 15. This technical report covers electronic control gear for double-capped fluorescent lamps fitted with G5 or G13 lamp caps and to single-capped fluorescent lamps fitted with lamp caps: 2GX7, 2G8, 2G10, 2G11, 2GX13, G23, GX23, G24q, GX24q, GR8, and GR10q. It is specifically applicable for equipment to be connected to 230 V - 50 Hz mains power networks. For other power systems, modifications may be necessary. This first edition of CISPR/TR 30-1 cancels and replaces the first edition of CISPR/TR 30 published in 2001. It is a technical revision which includes the following significant technical changes with respect to the previous edition: - minor correction of wiring distances of reference luminaire in Figure A.1; - addition of reference luminaires for electronic control gear with output terminals on both ends; - addition of reference luminaires for electronic control gear for circular-shaped fluorescent lamps; and - introduction of control gear marking indicating suitability for application in protection class I and/or class II luminaires.

Test method on electromagnetic emissions - Part 1: Electronic control gear for single- and double-capped fluorescent lamps

GSO CISPR 16-1-5:2021 无线电骚扰和抗扰度测量设备和方法规范 第1-5部分：无线电骚扰和抗扰度测量设备 5 MHz 至 18 GHz 的天线校准场地和参考测试场地

CISPR 16-1-5:2014 specifies the requirements for calibration sites in the frequency range 5 MHz to 18 GHz used to perform antenna calibrations according to CISPR 16-1-6. It also specifies the requirements for reference test sites that are used for the validation of compliance test sites in the frequency range 30 MHz to 1 000 MHz according to CISPR 16-1-4. It has the status of a basic EMC standard in accordance with IEC Guide 107. Measurement instrumentation specifications are given in CISPR 16-1-1 and CISPR 16-1-4. Further information and background on uncertainties in general is given in CISPR 16-4, which can also be helpful in establishing uncertainty estimates for the calibration processes of antennas and site validation measurements. This second edition cancels and replaces the first edition published in 2003, and its Amendment 1 (2012). It constitutes a technical revision which includes the following significant technical changes with respect to the previous edition: - site validation methods for other sites covered in CISPR 16-1-6 are added; - smaller step sizes are specified for swept frequency measurements; - the minimum ground plane size is increased; - and other miscellaneous technical and editorial refinements are included. Keywords: electromagnetic compatibility The contents of the corrigendum 1 of August 2020 have been included in this copy.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration sites and reference test sites for 5 MHz to 18 GHz

GSO CISPR TR 16-4-1:2021 无线电骚扰和抗扰度测量设备和方法规范 第4-1部分：不确定性、统计和极限建模 标准化 EMC 测试中的不确定性

CISPR/TR 16-4-1:2009 gives guidance on the treatment of uncertainties to those who are involved in the development or modification of CISPR electromagnetic compatibility (EMC) standards. In addition, this part provides useful background information for those who apply the standards and the uncertainty aspects in practice. The objectives of this part are to: a) identify the parameters or sources governing the uncertainty associated with the statement that a given product complies with the requirement specified in a CISPR recommendation. This uncertainty will be called "standards compliance uncertainty"; b) give guidance on the estimation of the magnitude of the standards compliance uncertainty; c) give guidance for the implementation of the standards compliance uncertainty into the compliance criterion of a CISPR standardised compliance test. As such, this part can be considered as a handbook that can be used by standards writers to incorporate and harmonise uncertainty considerations in existing and future CISPR standards. This part also gives guidance to regulatory authorities, accreditation bodies and test engineers to judge the performance quality of an EMC test-laboratory carrying out CISPR standardised compliance tests. The uncertainty considerations given in this part can also be used as guidance when comparing test results (and their uncertainties) obtained by using different alternative test methods. The uncertainty of a compliance test also relates to the probability of occurrence of an electromagnetic interference (EMI) problem in practice. This aspect is recognized and introduced briefly in this part. However, the problem of relating uncertainties of a compliance test to the occurrence of EMI in practice is not considered within the scope of this part. The scope of this part is limited to all the relevant uncertainty considerations of a standardized EMC compliance test. This second edition of CISPR 16-4-1 cancels and replaces the first edition published in 2003, and its Amendments 1 (2004) and 2 (2007). It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition. The provisions available for application of uncertainties in the determination of the compliance criterion are explained more generally and a procedure is added for re-testing an approved EUT by another test house.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-1: Uncertainties, statistics and limit modelling - Uncertainties in standardized EMC tests

GSO CISPR 16-2-3:2021 无线电骚扰和抗扰度测量设备和方法规范 第2-3部分：骚扰和抗扰度测量方法 辐射骚扰测量

CISPR 16-2-3:2016 is available as CISPR 16-2-3:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. CISPR 16-2-3:2016 specifies the methods of measurement of radiated disturbance phenomena in the frequency range of 9 kHz to 18 GHz. The aspects of measurement uncertainty are specified in CISPR 16-4-1 and CISPR 16-4-2. It has the status of a basic EMC publication in accordance with IEC Guide 107, "Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications". This fourth edition edition cancels and replaces the third edition published in 2010, its Amendment 1:2010 and its Amendment 2:2014. This edition constitutes a technical revision.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements

GSO CISPR TR 30-2:2021 电磁辐射测试方法 第2部分：放电灯电子控制装置（荧光灯除外）

CISPR/TR 30-2:2012(E), which is a technical report, details with the aid of reference luminaires, an independent method by which the radio disturbance characteristics of built-in electronic control gear for discharge (excluding fluorescent) lamp luminaires with protection classes I and/or II may be compared against the requirements of CISPR 15. The scope of the part is limited to electronic lamp control gear with an output power (lamp power) up to and including 150 W. Independent electronic lamp control gears are not covered by this technical report; they are within the scope of CISPR 15. This first edition of CISPR/TR 30-2 is published in conjunction with CISPR/TR 30-1. Each part of CISPR 30 series is independent and describes the test set-up for electronic control gear use together with a special lamp family.

Test method on electromagnetic emissions - Part 2: Electronic control gear for discharge lamps excluding fluorescent lamps

GSO CISPR 16-1-1:2021 无线电骚扰和抗扰度测量设备和方法规范 第1-1部分：无线电骚扰和抗扰度测量设备 测量设备

CISPR 16-1-1:2015 specifies the characteristics and performance of equipment for the measurement of radio disturbance in the frequency range 9 kHz to 18 GHz. In addition, requirements are provided for specialized equipment for discontinuous disturbance measurements. This fourth edition cancels and replaces the third edition published in 2010, Amendment 1:2010 and Amendment 2:2014. This edition constitutes a technical revision. The contents of the interpretation sheet 1 of April 2018 have been included in this copy.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus

GSO CISPR 16-1-4:2021 无线电骚扰和抗扰度测量设备和方法规范 第1-4部分：无线电骚扰和抗扰度测量设备 辐射骚扰测量的天线和测试场地

CISPR 16-1-4:2010+A1:2012+A2:2017 specifies the characteristics and performance of equipment for the measurement of radiated disturbances in the frequency range 9 kHz to 18 GHz. Specifications for antennas and test sites are included. The requirements of this publication apply at all frequencies and for all levels of radiated disturbances within the CISPR indicating range of the measuring equipment. Methods of measurement are covered in Part 2-3, and further information on radio disturbance is given in Part 3 of CISPR 16. Uncertainties, statistics and limit modelling are covered in Part 4 of CISPR 16. This third edition of CISPR 16-1-4 cancels and replaces the second edition published in 2007 and its Amendments 1 (2007) and 2 (2008). It is a technical revision. This edition includes the following significant technical change with respect to the previous edition: provisions are added to address evaluation of a set-up table in the frequency range above 1 GHz. CISPR 16-1-4:2010 has the status of a basic EMC publication in accordance with IEC Guide 107, Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications. This consolidated version consists of the third edition (2010), its amendment 1 (2012) and its amendment 2 (2017). Therefore, no need to order amendment in addition to this publication.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements

GSO CISPR 16-2-4:2021 无线电骚扰和抗扰度测量设备和方法规范 第2-4部分：骚扰和抗扰度测量方法 抗扰度测量

This part of CISPR 16 is designated a basic standard, which specifies the methods of measurement of immunity to EMC phenomena in the frequency range 9 kHz to 18 GHz. CISPR 16-2 has been reorganised into 4 parts, to accommodate growth and easier maintenance. This first edition of CISPR 16-2-4, together with CISPR 16-2-1, CISPR 16-2-2 and CISPR 16-2-3, cancels and replaces the second edition of CISPR 16-2, published in 2003. It contains the relevant clauses of CISPR 16-2 without technical changes.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-4: Methods of measurement of disturbances and immunity - Immunity measurements

GSO CISPR 16-2-2:2021 无线电骚扰和抗扰度测量设备和方法规范 第2-2部分：骚扰和抗扰度测量方法 骚扰功率测量

CISPR 16-2-2:2010 specifies the methods of measurement of disturbance power using the absorbing clamp in the frequency range 30 MHz to 1 000 MHz. This second edition cancels and replaces the first edition (2003), its Amendment 1 (2004) and Amendment 2 (2005). It constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition: provisions for the use of spectrum analyzers for compliance measurements (Annex D) and the use of FFT-based test instrumentation (Clauses 3, 6 and 8) are now included. CISPR 16-2-2:2010 has the status of a basic EMC publication in accordance with IEC Guide 107, Electromagnetic compatibility - Guide to the drafting of electromagnetic compatibility publications.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power

GSO CISPR TR 16-2-5:2021 无线电骚扰和抗扰度测量设备和方法规范 第2-5部分：大型物理设备产生的干扰发射的现场测量

CISPR 16-2-5:2008(E) deals with in situ electromagnetic disturbance measurements in any environment from physically large equipment and systems excluding networks. It covers both radiated and conducted emission phenomena, and does not deal with immunity tests. This technical report is intended to be applied primarily to such physically large equipment which are not under the scope of any existing emission standards (as for example CISPR 11 and CISPR 22). It serves only as a guideline on how to deal with emissions of that equipment at the particular location of installation. It does not establish any emission requirements. Due to the severe impact of the conditions existing at a particular location of operation and the use of the respective large equipment, however, it is not intended to use the measurements in the frame of type testing. Reference in-situ measurement distances will be given. This allows comparison of the measurement results with limits from existing relevant standards. The frequency range under consideration is from 9 kHz to 18 GHz.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-5: In situ measurements for disturbing emissions produced by physically large equipment

GSO IEC 62153-4-12:2021 金属通信电缆测试方法 第4-12部分：电磁兼容性（EMC）连接硬件的耦合衰减或屏蔽衰减吸收钳法

IEC 62153-4-13:2009(E) details the method of test to determine the coupling attenuation or screening attenuation for connecting hardware used in analogue and digital communication systems. The test method details means to test one part of a connecting hardware (e. g. wall outlet or plug alone) as well as testing a mated pair of connecting hardware. This publication is to be read in conjunction with IEC 62153-4-5:2006.

Metallic communication cable test methods - Part 4-12: Electromagnetic compatibility (EMC) - Coupling attenuation or screening attenuation of connecting hardware - Absorbing clamp method

GSO CISPR 25:2021 车辆、船舶和内燃机 无线电骚扰特性 保护车载接收器的限值和测量方法

CISPR 25:2016 contains limits and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 2 500 MHz. The standard applies to any electronic/electrical component intended for use in vehicles, trailers and devices. Refer to International Telecommunications Union (ITU) publications for details of frequency allocations. The limits are intended to provide protection for receivers installed in a vehicle from disturbances produced by components/modules in the same vehicle. The method and limits for a complete vehicle (whether connected to the power mains for charging purposes or not) are in Clause 5 and the methods and limits for components/modules are in Clause 6. Only a complete vehicle test can be used to determine the component compatibility with respect to a vehicle's limit. The receiver types to be protected are, for example, broadcast receivers (sound and television), land mobile radio, radio telephone, amateur, citizens' radio, Satellite Navigation (GPS etc.), Wi-Fi and Bluetooth. For the purpose of this standard, a vehicle is a machine, which is self-propelled by an internal combustion engine, electric means, or both. Vehicles include (but are not limited to) passenger cars, trucks, agricultural tractors and snowmobiles. Annex A provides guidance in determining whether this standard is applicable to particular equipment. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - inclusion of charging mode for electric vehicles (EV) and plug-in electric vehicles (PHEV), - the methods for chamber validation have been included, - test methods for shielded power supply systems for high voltages for electric and hybrid electric vehicles have been included, - overall improvement. The contents of the corrigendum of October 2017 have been included in this copy.

Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers

GSO CISPR 16-1-3:2021 无线电骚扰和抗扰度测量设备和方法规范 第1-3部分：无线电骚扰和抗扰度测量设备 辅助设备 骚扰功率

CISPR 16-1-3:2004+A1:2016+A2:2020 is designated a basic standard, which specifies the characteristics and calibration of the absorbing clamp for the measurement of radio disturbance power in the frequency range 30 MHz to 1 GHz. This second edition cancels and replaces the first edition published in 2003. It constitutes a technical revision. In this edition a more detailed calibration method for the absorbing clamp is specified. Furthermore, new alternative calibration methods are introduced which are more practicable than the one which was specified previously. Additional parameters to describe the absorbing clamp are defined, like the decoupling factor for the broadband absorber (DF) and the decoupling factor for the current transformer (DR), along with their validation methods. A procedure for the validation of the absorbing clamp test site (ACTS) is also included in the of the absorbing clamp test site (ACTS) is also included in the document. The contents of the corrigendum of February 2006 have been included in this copy. This consolidated version consists of the second edition (2004), its amendment 1 (2016) and its amendment 2 (2020). Therefore, no need to order amendments in addition to this publication.

Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-3: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Disturbance power

OVE EN IEC 55011 (Fragment 1):2021 工业、科学和医疗设备 射频干扰特性 限值和测量方法 气隙无线电力传输（WPT）要求（IEC CIS/B/763/CDV）（英文版）

Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement - Requirements for air-gap wireless power transfer (WPT) (IEC CIS/B/763/CDV) (english version)

LST EN 55011/A2-2021 工业、科学和医疗设备 射频干扰特性 限值和测量方法（CISPR 11:2015/A2:2019）

Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement (CISPR 11:2015/A2:2019)

LST EN IEC 61000-3-2/A1:2021 电磁兼容性（EMC） 第 3-2 部分：限制 谐波电流发射限制（设备输入电流每相 16 A）（IEC 61000-3-2:2018/A1:2020）

Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ?16 A per phase) (IEC 61000-3-2:2018/A1:2020)